doesn't automatically clear when VDD rises above Vlow again and needs to be
cleared manually. However, apparently this needs all of the time registers
to be set, i.e. pcf8563_settime(), and not just PCF8563_R_SECOND in order
for PCF8563_R_SECOND_VL to stick. Thus, we just issue a warning during
pcf8563_attach() rather than failing with ENXIO in case it is set.
MFC after: 3 days
Add a Simple polled driver iicoc for the OpenCores I2C controller. This
is used in Netlogic XLP processors.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro com)
The earlier version of the driver is sys/mips/rmi/dev/iic/ds1374u.c
Convert all references to ds1374u to ds1374, and use DEVMETHOD_END.
Also update the license header as Netlogic is now Broadcom.
clients.
These are helful when making certain drivers work on both Linux
and FreeBSD without changing the code flow too much.
Reviewed by: kib, wlosh
MFC after: 1 month
* Right now the delay is hard coded at 10uS. This is a bit long when doing lots
of periodic i2c transactions. So create a 'udelay' parameter and initialise it
to 10. This can be tuned later.
* Add a newline after a transaction finishes, so the debugging output isn't so
horrible.
These realtek switch PHYs speak a variant of i2c with some slightly
modified handling.
From the submitter, slightly modified now that some further digging
has been done:
The I2C framework makes a assumption that the read/not-write bit of the first
byte (the address) indicates whether reads or writes are to follow.
The RTL8366 family uses the bus: after sending the address+read/not-write byte,
two register address bytes are sent, then the 16-bit register value is sent
or received. While the register write access can be performed as a 4-byte
write, the read access requires the read bit to be set, but the first two bytes
for the register address then need to be transmitted.
This patch maintains the i2c protocol behaviour but allows it to be relaxed
(for these kinds of switch PHYs, and whatever else Realtek may do with this
almost-but-not-quite i2c bus) - by setting the "strict" hint to 0.
The "strict" hint defaults to 1.
Submitted by: Stefan Bethke <stb@lassitu.de>
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
setting (either default or if supported as set by SIOCSIFFIB, e.g.
from ifconfig).
Submitted by: Alexander V. Chernikov (melifaro ipfw.ru)
Reviewed by: julian
MFC after: 2 weeks
- Add retry loops in the i2c read/write functions.
- Combied the ADC channel selection and readout of the value into
one iicbus_transfer to avoid possible races.
Reviewed by: nwhitehorn
- Add a retry loop for the i2c sensor reading.
- Check on busy status of the chip and on invalid values.
- Fix a typo in a comment.
- Replace the constant 2732 with the ZERO_C_TO_K macro.
Approved by: nwhitehorn (mentor)
- Add a retry loop for the i2c sensor reading.
- Update the sensor handling for sensors which do not have a location
entry. [1]
Submitted by: [1] Justin Hibbits.
Approved by: nwhitehorn (mentor)
for this sensor. Instead of leaving this location empty we use here
the default name 'sensor'.
Submitted by: Justin Hibbits <chmeeedalf at gmail dot com>
Approved by: nwhitehorn (mentor)
functionality is the same, a difference is that the DS1775 has a better
precision than the LM75. But we do not use it in our setup. Make the
LM75 work the same as the DS1775.
Fix a typo in device_set_desc.
Tested by: Paul Mather <paul at gromit dlib vt edu>
Approved by: nwhitehorn (mentor)
PowerMac7,2.
- The fcu driver lets us read and write the fan RPMs for all fans in the
PowerMac7,2. This driver is PowerMac specific.
- The ds1775 is a driver to read the temperature for the drive bay sensor.
- The max6690 is another driver to read temperatures. Here it is used to
read the inlet, the backside and the U3 heatsink temperature.
An additional driver, the ad7417, will follow later.
Thanks to nwhitehorn for guiding me through this driver development.
Approved by: nwhitehorn (mentor)
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
respectivly. This will allow one to have a kernel with both devices
present and use it for multiple boards with different types of RTC
sitting on a bus.
Discussed with: imp
work when the bus attaches its own children. Instead of hardcoding a unit
number and returning BUS_PROBE_NOWILDCARD, which will break multiple iicbus
systems, check in the probe routine whether the device address is 0. Real
I2C devices will never have this address, but devices added with
BUS_ADD_CHILD() will.
Requested by: jhb
Reviewed by: jhb
indicated I2C devices, and provides an ofw_bus interface for driver probing.
This should be MI, but is currently provided only on PowerPC due to lack of
sparc64 hardware with an I2C controller.
Discussed on: freebsd-arch
