NETGRAPH is not present in GENERIC at the moment. Also, change some
settings to support USB installs:
- Add KBD_INSTALL_CDEV as an option to make /dev/kbd[01] actually work.
- Turn on keyboard probing in sc0. The syscons driver will now use a
flag documented in ukbd(4) but not in sc(4) that tells syscons to
actively search for a keyboard device if none is found. This allows
USB keyboards to just be plugged in and instantly start working.
- Require the atkbd0 driver to actually probe to see if a keyboard is
there. This allows USB keyboards to be seen by sc0 if an AT keyboard
isn't plugged into the computer. This also means that you will no
longer be able to plug an AT keyboard into a machine after it has
booted a GENERIC kernel and use it. AT keyboards aren't designed for
this anyway. USB keyboards are designed for this, and they work.
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
o Drop all broadcast and multicast source addresses in tcp_input.
o Enable ICMP_BANDLIM in GENERIC.
o Change default to 200/s from 100/s. This will still stop the attack, but
is conservative enough to do this close to code freeze.
This is not the optimal patch for the problem, but is likely the least
intrusive patch that can be made for this.
Obtained from: Don Lewis and Matt Dillon.
Reviewed by: freebsd-security
NICs. (Finally!) The PCMCIA, ISA and PCI varieties are all supported,
though only the ISA and PCI ones will work on the alpha for now.
PCCARD, ISA and PCI attachments are all provided. Also provided an
ancontrol(8) utility for configuring the NIC, man pages, and updated
pccard.conf.sample. ISA cards are supported in both ISA PnP and hard-wired
mode, although you must configure the kernel explicitly to support the
hardwired mode since you have to know the I/O address and port ahead
of time.
Special thanks to Doug Ambrisko for doing the initial newbus hackery
and getting it to work in infrastructure mode.
USB-EL1202A chipset. Between this and the other two drivers, we should
have support for pretty much every USB ethernet adapter on the market.
The only other USB chip that I know of is the SMC USB97C196, and right
now I don't know of any adapters that use it (including the ones made
by SMC :/ ).
Note that the CATC chip supports a nifty feature: read and write combining.
This allows multiple ethernet packets to be transfered in a single USB
bulk in/out transaction. However I'm again having trouble with large
bulk in transfers like I did with the ADMtek chip, which leads me to
believe that our USB stack needs some work before we can really make
use of this feature. When/if things improve, I intend to revisit the
aue and cue drivers. For now, I've lost enough sanity points.
Kawasaki LSI KL5KUSB101B chip, including the LinkSys USB10T, the
Entrega NET-USB-E45, the Peracom USB Ethernet Adapter, the 3Com
3c19250 and the ADS Technologies USB-10BT. This device is 10mbs
half-duplex only, so there's miibus or ifmedia support. This device
also requires firmware to be loaded into it, however KLSI allows
redistribution of the firmware images (I specifically asked about
this; they said it was ok).
Special thanks to Annelise Anderson for getting me in touch with
KLSI (eventually) and thanks to KLSI for providing the necessary
programming info.
Highlights:
- Add driver files to /sys/dev/usb
- update usbdevs and regenerate attendate files
- update usb_quirks.c
- Update HARDWARE.TXT and RELNOTES.TXT for i386 and alpha
- Update LINT, GENERIC and others for i386, alpha and pc98
- Add man page
- Add module
- Update sysinstall and userconfig.c
USB ethernet chip. Adapters that use this chip include the LinkSys
USB100TX. There are a few others, but I'm not certain of their
availability in the U.S. I used an ADMtek eval board for development.
Note that while the ADMtek chip is a 100Mbps device, you can't really
get 100Mbps speeds over USB. Regardless, this driver uses miibus to
allow speed and duplex mode selection as well as autonegotiation.
Building and kldloading the driver as a module is also supported.
Note that in order to make this driver work, I had to make what some
may consider an ugly hack to sys/dev/usb/usbdi.c. The usbd_transfer()
function will use tsleep() for synchronous transfers that don't complete
right away. This is a problem since there are times when we need to
do sync transfers from an interrupt context (i.e. when reading registers
from the MAC via the control endpoint), where tsleep() us a no-no.
My hack allows the driver to have the code poll for transfer completion
subject to the xfer->timeout timeout rather that calling tsleep().
This hack is controlled by a quirk entry and is only enabled for the
ADMtek device.
Now, I'm sure there are a few of you out there ready to jump on me
and suggest some other approach that doesn't involve a busy wait. The
only solution that might work is to handle the interrupts in a kernel
thread, where you may have something resembling a process context that
makes it okay to tsleep(). This is lovely, except we don't have any
mechanism like that now, and I'm not about to implement such a thing
myself since it's beyond the scope of driver development. (Translation:
I'll be damned if I know how to do it.) If FreeBSD ever aquires such
a mechanism, I'll be glad to revisit the driver to take advantage of
it. In the meantime, I settled for what I perceived to be the solution
that involved the least amount of code changes. In general, the hit
is pretty light.
Also note that my only USB test box has a UHCI controller: I haven't
I don't have a machine with an OHCI controller available.
Highlights:
- Updated usb_quirks.* to add UQ_NO_TSLEEP quirk for ADMtek part.
- Updated usbdevs and regenerated generated files
- Updated HARDWARE.TXT and RELNOTES.TXT files
- Updated sysinstall/device.c and userconfig.c
- Updated kernel configs -- device aue0 is commented out by default
- Updated /sys/conf/files
- Added new kld module directory
now. On one machine with <825a> and <875> controllers, `sym' correctly
attached. On another one with only a <ncr 53c810 fast10 scsi>, the `ncr'
driver correctly attached.
3.3R and then to -current. The pccard support has been left in the
driver, but is presently non-functional because we are using the
isa_compat layer for the moment.
Obtained From: PAO
Sponsored by: Timing Solutions
These drivers were cloned from the ed and ep drivers back in 1994
when PCMCIA cards were a very new thing and we had no other support
for such devices. They treated the PCIC (the chip which controls the
PCCARD slot) as part of their device and generally hacked their way
to success. They have significantly bit-rotted relative to their
ancestor drivers (ed & ep) and they were a dead-end on the evolution
path to proper PCCARD support in FreeBSD.
They have been terminally broken since August 18 where mdodd forgot
them and nobody seems to have missed them enough to fix them since.
I found no outstanding PRs against these drivers.
