Some clocks used the NM type but this clock is for the ones with the
formula "clk = clkin / n / m" and not "clk = clkin * n / m"
Use the new frac clock for them.
Add a clock driver for clock that can either be used in integer mode
with one N factor and one M divider or in fractional mode where the
output frequency is chosen between two predifined output.
This was enumerated with exhaustive search for sys/eventhandler.h includes,
cross-referenced against EVENTHANDLER_* usage with the comm(1) utility. Manual
checking was performed to avoid redundant includes in some drivers where a
common os_bsd.h (for example) included sys/eventhandler.h indirectly, but it is
possible some of these are redundant with driver-specific headers in ways I
didn't notice.
(These CUs did not show up as missing eventhandler.h in tinderbox.)
X-MFC-With: r347984
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
Having IPSEC compiled into the kernel imposes a non-trivial
performance penalty on multi-threaded workloads due to IPSEC
refcounting. In my benchmarks of multi-threaded UDP
transmit (connected sockets), I've seen a roughly 20% performance
penalty when the IPSEC option is included in the kernel (16.8Mpps
vs 13.8Mpps with 32 senders on a 14 core / 28 HTT Xeon
2697v3)). This is largely due to key_addref() incrementing and
decrementing an atomic reference count on the default
policy. This cause all CPUs to stall on the same cacheline, as it
bounces between different CPUs.
Given that relatively few users use ipsec, and that it can be
loaded as a module, it seems reasonable to ask those users to
load the ipsec module so as to avoid imposing this penalty on the
GENERIC kernel. Its my hope that this will make FreeBSD look
better in "out of the box" benchmark comparisons with other
operating systems.
Many thanks to ae for fixing auto-loading of ipsec.ko when
ifconfig tries to configure ipsec, and to cy for volunteering
to ensure the the racoon ports will load the ipsec.ko module
Reviewed by: cem, cy, delphij, gnn, jhb, jpaetzel
Differential Revision: https://reviews.freebsd.org/D20163
tun(4) and tap(4) share the same general management interface and have a lot
in common. Bugs exist in tap(4) that have been fixed in tun(4), and
vice-versa. Let's reduce the maintenance requirements by merging them
together and using flags to differentiate between the three interface types
(tun, tap, vmnet).
This fixes a couple of tap(4)/vmnet(4) issues right out of the gate:
- tap devices may no longer be destroyed while they're open [0]
- VIMAGE issues already addressed in tun by kp
[0] emaste had removed an easy-panic-button in r240938 due to devdrn
blocking. A naive glance over this leads me to believe that this isn't quite
complete -- destroy_devl will only block while executing d_* functions, but
doesn't block the device from being destroyed while a process has it open.
The latter is the intent of the condvar in tun, so this is "fixed" (for
certain definitions of the word -- it wasn't really broken in tap, it just
wasn't quite ideal).
ifconfig(8) also grew the ability to map an interface name to a kld, so
that `ifconfig {tun,tap}0` can continue to autoload the correct module, and
`ifconfig vmnet0 create` will now autoload the correct module. This is a
low overhead addition.
(MFC commentary)
This may get MFC'd if many bugs in tun(4)/tap(4) are discovered after this,
and how critical they are. Changes after this are likely easily MFC'd
without taking this merge, but the merge will be easier.
I have no plans to do this MFC as of now.
Reviewed by: bcr (manpages), tuexen (testing, syzkaller/packetdrill)
Input also from: melifaro
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D20044
Use it wherever COMPAT_FREEBSD11 is currently specified, like r309749.
Reviewed by: imp, jhb, markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20120
We don't have the display engine driver commited in FreeBSD yet so it is
useless to expose the clocks yet (and also it have not been tested on H5).
Reported by: Manuel Stühn (freebsdnewbie@freenet.de)
PR: 237571
MFC after: 1 week
Allwinner H3 and H5 share many internal components, that's why they can
use the same drivers.
This patch adds the compatible strings to enable clock drivers
probing on Allwinner NanoPI NEO2 device.
Tested on: NanoPi NEO2 (by submitter), OrangePi PC2 (by manu)
Submitted by: Manuel Stühn (freebsdnewbie@freenet.de)
MFC after: 2 months
Differential Revision: https://reviews.freebsd.org/D20069
occasional spurious interrupts are a normal thing on this hardware. Also,
change the name of the cpu-local interrupt controller driver from local_intc
to lintc, because the name gets built into interrupt names, which have to
fit into a 19-byte field for stats reporting (so this allows 5 more bytes
of the actual interrupt name to be displayed).
Due to three conditions the codec driver for Allwinner A10/A20 and H3/H5 did not work properly here:
Wrong bit position for the analog audio reset
Hardware Reset of codec was not de-asserted correctly
Linux DTS file did not contain the address of the analog register the way as the driver was expecting it.
This patch proposes fixes for those three parts.
Submitted by: freebsdnewbie@freenet.de (Manuel Stühn)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19910
The code previously set up interrupt handlers for all the interrupt
resources available, including for timers that are not in use. That could
lead to interrupt storms. For example, if boot firmware enabled the virtual
timer but the kernel is using the physical timer, it could get flooded with
interrupts on the virtual timer which it cannot shut off. By only setting
up an interrupt handler for the hardware that will actually be used, any
interrupts from other timer units will remain masked in the interrupt
controller.
Differential Revision: https://reviews.freebsd.org/D19871
The old clocks are disconneted from the build since r337344.
Remove all those pseudo drivers. The only one remaining is for gmac
(the ethernet controller) so move it to sys/arm/allwinner.
While here remove a83t support from gmacclk as it is unneeded since r326114.
MFC after: 1 month
Since 5.0 DTS the syscon controller have a new compatible as it
exports new subnodes, we currently only use it as a syscon provider
so just add the new compatible.
Tested On: H3
MFC after: 1 month
Since latest DTS update the rtc is supposed to register two clocks :
- osc32k (the 32k oscillator on the board that the RTC uses directly and
that other peripheral can use)
- iosc (the internal oscillator of the RTC when available which frequency
depend on the SoC revision)
Since we need the RTC before the proper clock control unit (because it uses
those clocks) attach it a BUS_PASS_BUS + MIDDLE and attach the clock control
unit at BUS_PASS_BUS + LAST for the SoC that requires it.
Tested On: A20, H3, A64
MFC after: 1 month
Correct a typo in the RPI-B ethernet config - the RPi-B includes a
SMC LAN9512 USB bridge and Ethernet 10/100 NIC/phy. The phy part of
this is supported by smscphy.
Tested On: RPi1 Model B
Approved by: grog, jhb (mentors)
MFC after: 3 days
Since r324184 the root node compatible for the original Raspberry Pi
is "brcm,bcm2835", add it to the compatible list of bcm2835_cpufreq.
Tested On: RPi1 Model B
Note that the default Das U-Boot FDT does not include a cpus clause
so actually adding a bcm2835_cpufreq device requires adding a FDT
overlay defining the cpu.
Approved by: grog, jhb (mentors)
MFC after: 3 days
If a custom block size requested, use it, otherwise revert to the previous logic
of using just a data size if it's less than MMC_BLOCK_SIZE, and MMC_BLOCK_SIZE otherwise.
Reviewed by: bz
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D19783
In r337703 DTS files were updated to Linux 4.18, including Linux commit
4d8b032d3c03f4e9788a18bbb51b10e6c9e8a56b which removed the `phy_id`
property from am335x-bone-common (as the property was deprecated).
Use `phy-handle` via fdt_get_phyaddr, keeping the existing code as a
fallback for old DTBs.
PR: 236624
Submitted by: manu, Gerald Aryeetey <aryeeteygerald_rogers.com>
Reported by: Gerald Aryeetey
Reviewed by: manu
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19814
Using DFLTPHYS/MAXPHYS is not always OK, instead make it possible for the
controller driver to provide maximum data size to MMCCAM, and use it there.
The old stack already does this.
Reviewed by: manu
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D15892
Similar to bcm2835_sdhost.c add a TUNABLE and SYSCTL to selectively
turn on debugging printfs if debugging is turned on at compile time.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Reviewed by: gonzo, andrew
Differential Revision: https://reviews.freebsd.org/D19745
When comparing best frequencies use the absolute value.
If we do not do that we end up choosing an always lower value than
the best one if the exact freq cannot be met.
MFC after: 2 weeks
In current code, the delay argument in FDT_PLATFORM_DEF(2) improperly
initialize refs field from kobj_class structure instead of delay_count
field.
This causes not working DELAY() function (due to never initialized
delay_count) in earlier boot stages, until the first timer was attached.
MFC after: 2 weeks
Add the infrastructure to allow MD procctl(2) commands, and use it to
introduce amd64 PTI control and reporting. PTI mode cannot be
modified for existing pmap, the knob controls PTI of the new vmspace
created on exec.
Requested by: jhb
Reviewed by: jhb, markj (previous version)
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D19514
PTI mode for the process pmap on exec is activated iff P_MD_PTI is set.
On exec, the existing vmspace can be reused only if pti mode of the
pmap matches the P_MD_PTI flag of the process. Add MD
cpu_exec_vmspace_reuse() callback for exec_new_vmspace() which can
vetoed reuse of the existing vmspace.
MFC note: md_flags change struct proc KBI.
Reviewed by: jhb, markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D19514
In all of the architectures we have today, we always use PAGE_SIZE.
While in theory one could define different things, none of the
current architectures do, even the ones that have transitioned from
32-bit to 64-bit like i386 and arm. Some ancient mips binaries on
other systems used 8k instead of 4k, but we don't support running
those and likely never will due to their age and obscurity.
Reviewed by: imp (who also contributed the commit message)
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D19280