and t_maxseg. This dualism emerged with T/TCP, but was not properly cleaned
up after T/TCP removal. After all permutations over the years the result is
that t_maxopd stores a minimum of peer offered MSS and MTU reduced by minimum
protocol header. And t_maxseg stores (t_maxopd - TCPOLEN_TSTAMP_APPA) if
timestamps are in action, or is equal to t_maxopd otherwise. That's a very
rough estimate of MSS reduced by options length. Throughout the code it
was used in places, where preciseness was not important, like cwnd or
ssthresh calculations.
With this change:
- t_maxopd goes away.
- t_maxseg now stores MSS not adjusted by options.
- new function tcp_maxseg() is provided, that calculates MSS reduced by
options length. The functions gives a better estimate, since it takes
into account SACK state as well.
Reviewed by: jtl
Differential Revision: https://reviews.freebsd.org/D3593
Add if_requestencap() interface method which is capable of calculating
various link headers for given interface. Right now there is support
for INET/INET6/ARP llheader calculation (IFENCAP_LL type request).
Other types are planned to support more complex calculation
(L2 multipath lagg nexthops, tunnel encap nexthops, etc..).
Reshape 'struct route' to be able to pass additional data (with is length)
to prepend to mbuf.
These two changes permits routing code to pass pre-calculated nexthop data
(like L2 header for route w/gateway) down to the stack eliminating the
need for other lookups. It also brings us closer to more complex scenarios
like transparently handling MPLS nexthops and tunnel interfaces.
Last, but not least, it removes layering violation introduced by flowtable
code (ro_lle) and simplifies handling of existing if_output consumers.
ARP/ND changes:
Make arp/ndp stack pre-calculate link header upon installing/updating lle
record. Interface link address change are handled by re-calculating
headers for all lles based on if_lladdr event. After these changes,
arpresolve()/nd6_resolve() returns full pre-calculated header for
supported interfaces thus simplifying if_output().
Move these lookups to separate ether_resolve_addr() function which ether
returs error or fully-prepared link header. Add <arp|nd6_>resolve_addr()
compat versions to return link addresses instead of pre-calculated data.
BPF changes:
Raw bpf writes occupied _two_ cases: AF_UNSPEC and pseudo_AF_HDRCMPLT.
Despite the naming, both of there have ther header "complete". The only
difference is that interface source mac has to be filled by OS for
AF_UNSPEC (controlled via BIOCGHDRCMPLT). This logic has to stay inside
BPF and not pollute if_output() routines. Convert BPF to pass prepend data
via new 'struct route' mechanism. Note that it does not change
non-optimized if_output(): ro_prepend handling is purely optional.
Side note: hackish pseudo_AF_HDRCMPLT is supported for ethernet and FDDI.
It is not needed for ethernet anymore. The only remaining FDDI user is
dev/pdq mostly untouched since 2007. FDDI support was eliminated from
OpenBSD in 2013 (sys/net/if_fddisubr.c rev 1.65).
Flowtable changes:
Flowtable violates layering by saving (and not correctly managing)
rtes/lles. Instead of passing lle pointer, pass pointer to pre-calculated
header data from that lle.
Differential Revision: https://reviews.freebsd.org/D4102
- The existing TCP INP_INFO lock continues to protect the global inpcb list
stability during full list traversal (e.g. tcp_pcblist()).
- A new INP_LIST lock protects inpcb list actual modifications (inp allocation
and free) and inpcb global counters.
It allows to use TCP INP_INFO_RLOCK lock in critical paths (e.g. tcp_input())
and INP_INFO_WLOCK only in occasional operations that walk all connections.
PR: 183659
Differential Revision: https://reviews.freebsd.org/D2599
Reviewed by: jhb, adrian
Tested by: adrian, nitroboost-gmail.com
Sponsored by: Verisign, Inc.
into mbuf storage, to reduce knowledge about mbuf/cluster layout in the
cxgb device driver.
Reviewed by: np
Sponsored by: EMC / Isilon Storage Division
sending not ready data:
o Add new flag to pru_send() flags - PRUS_NOTREADY.
o Add new protocol method pru_ready().
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
sb_cc member of struct sockbuf to a couple of inline functions:
sbavail() and sbused()
Right now they are equal, but once notion of "not ready socket buffer data",
will be checked in, they are going to be different.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
evicted from the syncache but a later syncache_expand succeeds because
of syncookies. The TOE driver has to resort to more direct means to
install its hooks in the socket in this case.
the TOE driver reports that an active open failed. toe_connect_failed is
supposed to handle this but it should be provided the inpcb instead of the
tcpcb which may no longer be around.
- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.
- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.
Build-tested with make universe.
30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE
Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe
Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe
Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
condition in proc_rwmem() and to (2) simplify the implementation of the
cxgb driver's vm_fault_hold_user_pages(). Specifically, in proc_rwmem()
the requested read or write could fail because the targeted page could be
reclaimed between the calls to vm_fault() and vm_page_hold().
In collaboration with: kib@
MFC after: 6 weeks
There is no need to use an atomic operation at structure initialization
time.
Note that the file changed is not connected to the build at this time.
Reviewed by: jhb (general issue)
Approved by: np
MFC after: 2 weeks
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
all pertinent statatistics for the subsystem. These structures are
sometimes "borrowed" by kernel modules that require a place to store
statistics for similar events.
Add KPI accessor functions for statistics structures referenced by kernel
modules so that they no longer encode certain specifics of how the data
structures are named and stored. This change is intended to make it
easier to move to per-CPU network stats following 8.0-RELEASE.
The following modules are affected by this change:
if_bridge
if_cxgb
if_gif
ip_mroute
ipdivert
pf
In practice, most of these statistics consumers should, in fact, maintain
their own statistics data structures rather than borrowing structures
from the base network stack. However, that change is too agressive for
this point in the release cycle.
Reviewed by: bz
Approved by: re (kib)
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.
Reviewed by: bz
Approved by: re (vimage blanket)
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
check missed this because cxgb's TOM is currently commented out of the build
system.
Submitted by: Navdeep Parhar <np at FreeBSD dot org>
Approved by: re (kensmith), kensmith (mentor temporarily unavailable)
the TCP syncache. This returns struct tcpopt to being private within the TCP
implementation, thus allowing it to be modified without ABI concerns.
The patch breaks the ABI. Bump __FreeBSD_version to 800103 accordingly. The cxgb
driver is the only TOE consumer affected by this change, and needs to be
recompiled along with the kernel.
Suggested by: rwatson
Reviewed by: rwatson, kmacy
Approved by: re (kensmith), kensmith (mentor temporarily unavailable)
previously always pointing to the default vnet context, to a
dynamically changing thread-local one. The currvnet context
should be set on entry to networking code via CURVNET_SET() macros,
and reverted to previous state via CURVNET_RESTORE(). Recursions
on curvnet are permitted, though strongly discuouraged.
This change should have no functional impact on nooptions VIMAGE
kernel builds, where CURVNET_* macros expand to whitespace.
The curthread->td_vnet (aka curvnet) variable's purpose is to be an
indicator of the vnet context in which the current network-related
operation takes place, in case we cannot deduce the current vnet
context from any other source, such as by looking at mbuf's
m->m_pkthdr.rcvif->if_vnet, sockets's so->so_vnet etc. Moreover, so
far curvnet has turned out to be an invaluable consistency checking
aid: it helps to catch cases when sockets, ifnets or any other
vnet-aware structures may have leaked from one vnet to another.
The exact placement of the CURVNET_SET() / CURVNET_RESTORE() macros
was a result of an empirical iterative process, whith an aim to
reduce recursions on CURVNET_SET() to a minimum, while still reducing
the scope of CURVNET_SET() to networking only operations - the
alternative would be calling CURVNET_SET() on each system call entry.
In general, curvnet has to be set in three typicall cases: when
processing socket-related requests from userspace or from within the
kernel; when processing inbound traffic flowing from device drivers
to upper layers of the networking stack, and when executing
timer-driven networking functions.
This change also introduces a DDB subcommand to show the list of all
vnet instances.
Approved by: julian (mentor)
TCPSTAT_INC(), rather than directly manipulating the fields across the
kernel. This will make it easier to change the implementation of
these statistics, such as using per-CPU versions of the data structures.
MFC after: 3 days
had been the only flag with random usage patterns.
Switch inc_flags to be used as a real bit field by using
INC_ISIPV6 with bitops to check for the 'isipv6' condition.
While here fix a place or two where in case of v4 inc_flags
were not properly initialized before.[1]
Found by: rwatson during review [1]
Discussed with: rwatson
Reviewed by: rwatson
MFC after: 4 weeks
1. separating L2 tables (ARP, NDP) from the L3 routing tables
2. removing as much locking dependencies among these layers as
possible to allow for some parallelism in the search operations
3. simplify the logic in the routing code,
The most notable end result is the obsolescent of the route
cloning (RTF_CLONING) concept, which translated into code reduction
in both IPv4 ARP and IPv6 NDP related modules, and size reduction in
struct rtentry{}. The change in design obsoletes the semantics of
RTF_CLONING, RTF_WASCLONE and RTF_LLINFO routing flags. The userland
applications such as "arp" and "ndp" have been modified to reflect
those changes. The output from "netstat -r" shows only the routing
entries.
Quite a few developers have contributed to this project in the
past: Glebius Smirnoff, Luigi Rizzo, Alessandro Cerri, and
Andre Oppermann. And most recently:
- Kip Macy revised the locking code completely, thus completing
the last piece of the puzzle, Kip has also been conducting
active functional testing
- Sam Leffler has helped me improving/refactoring the code, and
provided valuable reviews
- Julian Elischer setup the perforce tree for me and has helped
me maintaining that branch before the svn conversion
directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.
For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.
Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation
for virtualization.
Instead of initializing the affected global variables at instatiation,
assign initial values to them in initializer functions. As a rule,
initialization at instatiation for such variables should never be
introduced again from now on. Furthermore, enclose all instantiations
of such global variables in #ifdef VIMAGE_GLOBALS blocks.
Essentialy, this change should have zero functional impact. In the next
phase of merging network stack virtualization infrastructure from
p4/vimage branch, the new initialization methology will allow us to
switch between using global variables and their counterparts residing in
virtualization containers with minimum code churn, and in the long run
allow us to intialize multiple instances of such container structures.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
from the vimage project, as per plan established at devsummit 08/08:
http://wiki.freebsd.org/Image/Notes200808DevSummit
Introduce INIT_VNET_*() initializer macros, VNET_FOREACH() iterator
macros, and CURVNET_SET() context setting macros, all currently
resolving to NOPs.
Prepare for virtualization of selected SYSCTL objects by introducing a
family of SYSCTL_V_*() macros, currently resolving to their global
counterparts, i.e. SYSCTL_V_INT() == SYSCTL_INT().
Move selected #defines from sys/sys/vimage.h to newly introduced header
files specific to virtualized subsystems (sys/net/vnet.h,
sys/netinet/vinet.h etc.).
All the changes are verified to have zero functional impact at this
point in time by doing MD5 comparision between pre- and post-change
object files(*).
(*) netipsec/keysock.c did not validate depending on compile time options.
Implemented by: julian, bz, brooks, zec
Reviewed by: julian, bz, brooks, kris, rwatson, ...
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
- simplify page hold logic
- allow pages for processes other than that of curthread to
have pages held
- normalize the interface to more closely resemble the functions in
sys/vm
MFC after: 1 week
but an RW mapping exists for the underlying page. This change fixes the bug by using the
page / NULL returned from pmap_extract_and_hold to determine whether or not vm_fault needs
to be called.
The bug was pointed out by alc.
MFC after: 3 days
