desired role configuration instead of existing role. This gets
us out of the mess where we configured a role of NONE (or were
LAN only, for example), but didn't continue to attach the CAM
module (because we had neither initiator nor target role
set). Unfortunately, the code that rewrites NVRAM to match
actual to desired role only works if the CAM module attaches.
MFC after: 2 weeks
controller ported from NetBSD. It supports the following Gigabit
Ethernet adapters.
o Antares Microsystems Gigabit Ethernet
o ASUS NX1101 Gigabit Ethernet
o D-Link DL-4000 Gigabit Ethernet
o IC Plus IP1000A Gigabit Ethernet
o Sundance ST-2021 Gigabit Ethernet
o Sundance ST-2023 Gigabit Ethernet
o Sundance TC9021 Gigabit Ethernet
o Tamarack TC9021 Gigabit Ethernet
The IP1000A Gigabit Ethernet is also found on some motherboards
(LOM) from ABIT.
Unlike NetBSD stge(4) it does not require promiscuous mode operation
to revice packet and it supports all hardware features(TCP/UDP/IP
checksum offload, VLAN tag stripping/insertion features and JUMBO
frame) and polling(4).
Due to lack of hardware, hardwares that have TBI trantransceivers
were not tested at all.
Special thanks to wpaul who provided valauble datasheet for the
controller and helped to debug jumbo frame related issues. Whitout
his datasheet I would have spent many hours to debug this chip.
Tested on: i386, sparc64
mac-io bus, we cannot setup FAST interrupt handlers. This because we
use spinlocks to protect the hardware and all interrupt resources are
assigned the same interrupt handler. When the interrupt handler is
invoked for interrupt X, it could be preempted for interrupt Y while
it was holding the lock (where X and Y are the interrupt resources
corresponding a single instance of this driver). This is a deadlock.
By only using a MPSAFE handler in that case we prevent preemption.
The register layout has changed since the original NV4 - sigh.
Hotplug support has been fixed for all nVidia chipsets that supports it
(including the MCP51/55).
HW donated by: Kingsley College
locked.
- Move all the svr4 socket cache code into svr4_socket.c, specifically
move svr4_delete_socket() over from streams.c. Make the socket cache
entry structure and svr4_head private to svr4_socket.c as a result.
- Add a mutex to protect the svr4 socket cache.
- Change svr4_find_socket() to copy the sockaddr_un struct into a
caller-supplied sockaddr_un rather than giving the caller a pointer to
our internal one. This removes the one case where code outside of
svr4_socket.c could access data in the cache.
- Add an eventhandler for process_exit and process_exec to purge the cache
of any entries for the exiting or execing process.
- Add methods to init and destroy the socket cache and call them from the
svr4 ABI module's event handler.
- Conditionally grab Giant around socreate() in streamsopen().
- Use fdclose() instead of inlining it in streamsopen() when handling
socreate() failure.
- Only allocate a stream structure and attach it to a socket in
streamsopen(). Previously, if a svr4 program performed a stream
operation on an arbitrary socket not opened via the streams device,
we would attach streams state data to it and change f_ops of the
associated struct file while it was in use. The latter was especially
not safe, and if a program wants a stream object it should open it via
the streams device anyway.
- Don't bother locking so_emuldata in the streams code now that we only
touch it right after creating a socket (in streamsopen()) or when
tearing it down when the file is closed.
- Remove D_NEEDGIANT from the streams device as it is no longer needed.
renegotiation, we only initialize the hardware only when it is
absolutely required. Process SIOCGIFADDR ioctl in em(4) when we know
an IPv4 address is added. Handling SIOCGIFADDR in a driver is
layering violation but it seems that there is no easy way without
rewritting hardware initialization code to reduce settle time after
reset.
This should fix a long standing bug which didn't send ARP packet when
interface address is changed or an alias address is added. Another
effect of this fix is it doesn't need additional delays anymore when
adding an alias address to the interface.
While I'm here add a new if_flags into softc which remembers current
prgroammed interface flags and make use of it when we have to program
promiscuous mode.
Tested by: Atanas <atanas AT asd DOT aplus DOT net>
Analyzed by: rwatson
Discussed with: -stable
- Copy ethernet firmware down in small chunks so as to avoid bugs
in early versions of the bootstrap firmware.
- Attempt to "adopt" the running firmware if we cannot load a suitable
firmware image via firmware(9).
- Separate firmware validation into its own routine, and check the
major/minor driver/firmware ABI version.
instead of doing the first load with the BUS_DMA_NOWAIT flag. On 4.x with
PAE and > 4gb of RAM this proved disastrous if there weren't enough bounce
pages as amr_mapcmd() would return failure but the callback would later
fire once enough bounce pages were available and would then overwrite
another command's S/G list.
MFC after: 3 days
Submitted by: scottl (4.x version)
Reviewed by: scottl (port from 4.x to HEAD)
precedence uart. With my last change, it became a tie, and uart seems
to always win on my amd64. This was not my intention, so have sio be
just a tiny bit more preferred than uart.
Note: I'm not making any judgement on the merits of uart winning. I'm
just saying that if we want to change it, we do it on purpose.
FreeBSD repository and to clean up the license header so as to
not pollute the license with file function.
Zero all mailbox structures prior to use (just in case). Change
the outgoing mailbox count for INIT_FIRMWARE to be correct.
from a semantic point of view, but I notified the author of the driver
for confirmation. So far it at least fixes the build and should only
lead to not identifying or wrongly identifying a soundcard in the worst
case.
mark it as timed out. Don't try and free the config
request for read_cfg_header that times out because
it's still active. Put in code for the config reply
handler that will then free up timed out requests.
Fix the FC_PRIMITIVE_SEND completion to not try
and free a command twice. Dunno how this possibly
could have been working for awhile.
MFC after: 2 weeks
out ELS buffers but *don't* hang out commands,
we hang folks on the SAN because the LSI-Logic
f/w apparently sends back BUSY or QFULL or some
darn thing.
If we add command buffers, we have to respond to
them sensibly even if we don't have any upstream
listeners (scsi_targ or scsi_targ_bh), so put in
some local command reponse stuff.
MFC after: 2 weeks
sound cards with optional pseudo-multichannel playback.
It's based on snd_emu10k1 sound driver. Single channel version is available
from audio/emu10kx port since some time.
The two new ALSA header files (GPLed), which contain Audigy 2 ("p16v") and
Audigy 2 Value ("p17v") specific interfaces, are latest versions from ALSA
Mercurial repository.
This is not connected to the build yet.
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
latest version from Mercurial repository. It brings definition of some
additional Audigy 2 / Audigy 2 Value registers.
- Use new #defines from ALSA emu10k1.h
- Remove unused include files:
+ emu10k1-ac97.h was imported from ALSA and never used,
+ emu10k1.h was imported from Creative Linux emu10k1 driver, but only
AUDIGY_CODEBASE was used from it.
Submitted by: Yuriy Tsibizov <Yuriy.Tsibizov@gfk.ru>
forcing all transfers to do the start read/write stop by hand. Some
smart bridges prefer this sort of operation, and this allows us to
support their features more easily. When bridges don't support it, we
fall back to using the old-style opertaions. Expand the ioctl
interface to expose this function. Unlike the old-style interface,
this interface is thread safe, even on old bridges.
Add MEMORY_BARRIER for the few scratch dma ops that were missing
them plus add a couple of hi 32 bit dma ops (we could probably
allow 64 bit scratch and request/response queue dma now).
