o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
to COMPAT_43TTY.
Add COMPAT_43TTY to NOTES and */conf/GENERIC
Compile tty_compat.c only under the new option.
Spit out
#warning "Old BSD tty API used, please upgrade."
if ioctl_compat.h gets #included from userland.
via the DEFAULTS kernel configs. This allows folks to turn it that option
off in the kernel configs if desired without having to hack the source.
This is especially useful since PUC_FASTINTR hangs the kernel boot on my
ultra60 which has two uart(4) devices hung off of a puc(4) device.
I did not enable PUC_FASTINTR by default on powerpc since powerpc does not
currently allow sharing of INTR_FAST with non-INTR_FAST like the other
archs.
IPI_STOP IPIs.
- Change the i386 and amd64 MD IPI code to send an NMI if STOP_NMI is
enabled if an attempt is made to send an IPI_STOP IPI. If the kernel
option is enabled, there is also a sysctl to change the behavior at
runtime (debug.stop_cpus_with_nmi which defaults to enabled). This
includes removing stop_cpus_nmi() and making ipi_nmi_selected() a
private function for i386 and amd64.
- Fix ipi_all(), ipi_all_but_self(), and ipi_self() on i386 and amd64 to
properly handle bitmapped IPIs as well as IPI_STOP IPIs when STOP_NMI is
enabled.
- Fix ipi_nmi_handler() to execute the restart function on the first CPU
that is restarted making use of atomic_readandclear() rather than
assuming that the BSP is always included in the set of restarted CPUs.
Also, the NMI handler didn't clear the function pointer meaning that
subsequent stop and restarts could execute the function again.
- Define a new macro HAVE_STOPPEDPCBS on i386 and amd64 to control the use
of stoppedpcbs[] and always enable it for i386 and amd64 instead of
being dependent on KDB_STOP_NMI. It works fine in both the NMI and
non-NMI cases.
originally wrote it for 4.x and hasn't really had the time to fully update
it to 5.x and later. Also, the author doesn't use the hardware anymore as
well. If someone does need this driver they can always resurrect it from
the Attic.
Requested by: Frank Mayhar frank at exit dot com
This kernel config briefly describes some of the major MAC policies
available on FreeBSD. The hope is that this will raise the awareness
about MAC and get more people interested.
Discussed with: scottl
as they are already default for I686_CPU for almost 3 years, and
CPU_DISABLE_SSE always disables it. On the other hand, CPU_ENABLE_SSE
does not work for I486_CPU and I586_CPU.
This commit has:
- Removed the option from conf/options.*
- Removed the option and comments from MD NOTES files
- Simplified the CPU_ENABLE_SSE ifdef's so they don't
deal with CPU_ENABLE_SSE from kernel configuration. (*)
For most users, this commit should be largely no-op. If you used to
place CPU_ENABLE_SSE into your kernel configuration for some reason,
it is time to remove it.
(*) The ifdef's of CPU_ENABLE_SSE are not removed at this point, since
we need to change it to !defined(CPU_DISABLE_SSE) && defined(I686_CPU),
not just !defined(CPU_DISABLE_SSE), if we really want to do so.
Discussed on: -arch
Approved by: re (scottl)
FreeBSD based on aue(4) it was picked by OpenBSD, then from OpenBSD ported
to NetBSD and finally NetBSD version merged with original one goes into
FreeBSD.
Obtained from: http://www.gank.org/freebsd/cdce/
NetBSD
OpenBSD
This is mentioned in the Handbook but it is not as obvious to new
users why bpf is needed compared to the other largely self-explanatory
items in GENERIC.
PR: conf/40855
MFC after: 1 week
from 4.x kernel config files. User's wishing to upgrade from 4.x to 6
will need to go through 5.x, or grab this script from there. These
scripts will remain in RELENG_5...
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
It can be switched back once 5.3 is tested and released. Also turn on
PREEMPTION as many of the stability problems with it have been fixed.
MT5: 3 days.
remaining consumers to have the count passed as an option. This is
i4b, pc98/wdc, and coda.
Bump configvers.h from 500013 to 600000.
Remove heuristics that tried to parse "device ed5" as 5 units of the ed
device. This broke things like the snd_emu10k1 device, which required
quotes to make it parse right. The no-longer-needed quotes have been
removed from NOTES, GENERIC etc. eg, I've removed the quotes from:
device snd_maestro
device "snd_maestro3"
device snd_mss
I believe everything will still compile and work after this.
compile option. All FreeBSD packet filters now use the PFIL_HOOKS API and
thus it becomes a standard part of the network stack.
If no hooks are connected the entire packet filter hooks section and related
activities are jumped over. This removes any performance impact if no hooks
are active.
Both OpenBSD and DragonFlyBSD have integrated PFIL_HOOKS permanently as well.
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
lots of old interfaces, and digi now supports all cards that dgb
supported. The author of the driver says that this is no longer
necessary.
Approved by: babkin@
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
However, GENERIC has wdc commented out, and COMPAT_OLDISA is required
for that. Comment out COMPAT_OLDISA and sdd a comment to this effect
near wdc.
Reviewed by: nyan@
of the infrastructure for the gamma driver which was removed a while back.
The DRM_LINUX option is removed because the handler is now provided by the
linux compat code itself.
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
Fixed memory leak in the "nodevice" option implementation.
Use these instead of sed(1) in MD NOTES.
Use a single makefile (sys/conf/makeLINT.mk) to generate
LINT for all architectures. (Previous versions missed
the LINT dependency on Makefile, and i386 version also
missed the dependency on ${NOTES}.)
Fixed bugs in the previous NOTES conversion using the
"nodevice" token and sed(1):
- i386 LINT lost "device pst".
- pc98 LINT lost SC_*, MAXCONS and KBD_DISABLE_KEYMAP_LOAD
options, and got needless DPT_* options.
- Added nooptions PPC_DEBUG, PPC_PROBE_CHIPSET, KBD_INSTALL_CDEV
to sparc64 LINT so that it has a chance to config(8).
This basically returns us to where we were before.
point of not even compiling for a very long time.
Any effort spent unbreaking them would be better spent perfecting
the ata drivers for PC98, should any issues remain there.
This mostly consists of functionality to serialize accesses to
the two ATA channels (which can also be used to "fix" certain
PCI based controllers).
Add support for Acard controllers.
Enable the ATA driver in PC98 GENERIC, and add device hints.
Update man page with latest support.
The PC98 core team has kindly provided me with a PC98
machine that made this all possible, thanks to all that
contributed to that effort, without that this would
probably newer have been possible..
Approved by: re@
ACL configuration changes, this shouldn't result in different code paths
for file systems not explicitly configured for ACLs by the system
administrator. For UFS1, administrators must still recompile their
kernel to add support for extended attributes; for UFS2, it's sufficient
to enable ACLs using tunefs or at mount-time (tunefs preferred for
reliability reasons). UFS2, for a variety of reasons, including
performance and reliability, is the preferred file system for use with
ACLs.
Approved by: re
NB: But it will enable it in all kernels not having options "NO_GEOM"
Put the GEOM related options into the intended order.
Add "options NO_GEOM" to all kernel configs apart from NOTES.
In some order of controlled fashion, the NO_GEOM options will be
removed, architecture by architecture in the coming days.
There are currently three known issues which may force people to
need the NO_GEOM option:
boot0cfg/fdisk:
Tries to update the MBR while it is being used to control
slices. GEOM does not allow this as a direct operation.
SCSI floppy drives:
Appearantly the scsi-da driver return "EBUSY" if no media
is inserted. This is wrong, it should return ENXIO.
PC98:
It is unclear if GEOM correctly recognizes all variants of
PC98 disklabels. (Help Wanted! I have neither docs nor HW)
These issues are all being worked.
Sponsored by: DARPA & NAI Labs.
This is an architecture that present a thing message passing interface
to the OS. You can query as to how many ports and what kind are attached
and enable them and so on.
A less grand view is that this is just another way to package SCSI (SPI or
FC) and FC-IP into a one-driver interface set.
This driver support the following hardware:
LSI FC909: Single channel, 1Gbps, Fibre Channel (FC-SCSI only)
LSI FC929: Dual Channel, 1-2Gbps, Fibre Channel (FC-SCSI only)
LSI 53c1020: Single Channel, Ultra4 (320M) (Untested)
LSI 53c1030: Dual Channel, Ultra4 (320M)
Currently it's in fair shape, but expect a lot of changes over the
next few weeks as it stabilizes.
Credits:
The driver is mostly from some folks from Jeff Roberson's company- I've
been slowly migrating it to broader support that I it came to me as.
The hardware used in developing support came from:
FC909: LSI-Logic, Advansys (now Connetix)
FC929: LSI-Logic
53c1030: Antares Microsystems (they make a very fine board!)
MFC after: 3 weeks
