to the 802.11 layer if they are at least IEEE80211_MIN_LEN
o mask off interrupt status bits that we don't care about so we don't do
the wrong thing; this fixes a problem where the beacon miss interrupt status
bit is delivered together with other status bits when operating in monitor
mode (we would post a beacon miss swi and then do the wrong thing)
was added to the fast path to support the COM_IIR_RXRDYBUG() case even
when that case is not configured. This increased the relative overhead
of sio input by almost 25% in the worst case and by 2-3% in the usual
case (usually only about 0.2% absolute per port at 115200 bps). The
quick fix is to significantly pessimize only the COM_IIR_RXRDYBUG()
case.
safe since the 802.11 layer does the right thing for 11a operation)
o select short preamble operation based on the negotiated capabilities; not
just the local state/capability
o fillin the duration field in the 802.11 header as appropriate
o remove detection of 11g support; no longer needed
Obtained from: MADWIFI (with modifications)
we're on a 32-bit/64-bit bus or not. Use this to decide if we should
set the PCI dual-address cycle enable bit in the C+ command register.
(Enabling DAC on a 32-bit bus seems to do bad things.)
Also, initialize the C+ command register early in the re_init() routine.
The documentation says this register should be configured first.
We simply use the detected FIFO size to determine whether we have
a post 16550 UART or not. The support lacks proper serialization of
hardware access for now.
fixes a longstanding issue WRT resetting the chip after startup- it
would fail if we were connected as an F-port to a switch. If we
were connected as an F-port, we got assigned a hard loop ID of 255,
which is really a bogus loop id. Then when we turned around to
reset ourselves, the firmware would reject the ICB_INIT request
because the loop id was bogus. *sputter*
Minor fixlet from somebody in NetBSD with too much time on their
hands (dma -> DMA).
the "compatible" property too in the ns8250 case. This gets the serial
console to work on Blade 100s, where the device name is just "serial".
Reviewed by: marcel
Second (PPS) timing interface. The support is non-optional and by
default uses the DCD line signal as the pulse input. A compile-time
option (UART_PPS_ON_CTS) can be used to have uart(4) use the CTS line
signal.
Include <sys/timepps.h> in uart_bus.h to avoid having to add the
inclusion of that header in all source files.
Reviewed by: phk
This commit puts the relevant code snippets under #ifdef GONE_IN_5
(rather than #ifndef BURN_BRIDGES) thereby disabling the code now.
The code wil be entirely removed before 5.2 unless we find reasons
why this would be a bad idea.
Approach suggested by: imp
seems to be necessary for the 8139C+ under certain circumstances, and
doesn't appear to hurt the other chips. (In the failure case, the
packet would be sent through the TX DMA ring but not get echoed
back. I suspect this has something to do with the link state changing
unexpectedly.)
autoload and then copying the contends of the station address
registers. For some reason, reading the EEPROM on the 8169S doesn't
work right. This gets around the problem, and allows us to read
the station address correctly on the 8169S.
- Insert a delay after initiating packet transmition in re_diag() to
allow lots of time for the frame to echo back to the host, and wait
for both the 'RX complete' and 'timeout expired' bits in the ISR
register to be set.
- Deal more intelligently with the fact that the frame length
field in the RX descriptor is a different width on the 8139C+
than it is on the 8169/8169S/8110S
- For the 8169, you have to set bit 17 in the TX config register
to enter digital loopback mode, but for the 8139C+, you have to
set both bits 17 and 18. Take this into account so that re_diag()
works properly for both types of chips.
ethernet chips. This driver is pretty simple, however it contains
special DSP initialization code which is needed in order to get
the chip to negotiate a gigE link. (This special initialization
may not be needed in subsequent chip revs.) Also:
- Fix typo in if_rlreg.h (RL_GMEDIASTAT_1000MPS -> RL_GMEDIASTAT_1000MBPS)
- Deal with shared interrupts in re_intr(): if interface isn't up,
return.
- Fix another bug in re_gmii_writereg() (properly apply data field mask)
- Allow PHY driver to read the RL_GMEDIASTAT register via the
re_gmii_readreg() register (this is register needed to determine
real time link/media status).
method. This is necessary on ia64 where it's known that serial interfaces
described in the ACPI namespace may not have the well-known IRQs assigned
to them. This confuses us in thinking they are PCI based interrupts and
wrongly program the APIC.
for the 8169S, according to my sample board. The RealTek Linux driver
mentions 0x00800000. I'm assigning this to the 8110S until I get
more info on it. (The (preliminary) RealTek docs only say that 8169S/8110S
chips will have some combination of those two bits set, but doesn't say
exactly what bit combination goes with which chip variant.)
is not a size of 1. Since we already know there is a FIFO, we can
safely assume that it is at least 16 bytes. Note that all this is
mostly academic anyway. We don't use the size of the Rx FIFO
currently. If we add support for hardware flow control, we only
care about Rx FIFO sizes larger than 16.
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.
The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.
This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
