Now when one does 'make kernel ; make kernel' the second invocation
only does: `kernel.ko' is up to date.
rather than reproduce all the .fw files and relink the kernel.
Bring in a driver for the LSI Logic MPT2 6Gb SAS controllers.
This driver supports basic I/O, and works with SAS and SATA drives and
expanders.
Basic error recovery works (i.e. timeouts and aborts) as well.
Integrated RAID isn't supported yet, and there are some known bugs.
So this isn't ready for production use, but is certainly ready for
testing and additional development. For the moment, new commits to this
driver should go into the FreeBSD Perforce repository first
(//depot/projects/mps/...) and then get merged into -current once
they've been vetted.
This has only been added to the amd64 GENERIC, since that is the only
architecture I have tested this driver with.
Submitted by: scottl
Discussed with: imp, gibbs, will
Sponsored by: Yahoo, Spectra Logic Corporation
the existing code was very platform specific, and broken for SMP systems
trying to reboot from KDB.
- Add a new PLATFORM_RESET() method to the platform KOBJ interface, and
migrate existing reset functions into platform modules.
- Modify the OF_reboot() routine to submit the request by hand to avoid
the IPIs involved in the regular openfirmware() routine. This fixes
reboot from KDB on SMP machines.
- Move non-KDB reset and poweroff functions on the Powermac platform
into the relevant power control drivers (cuda, pmu, smu), instead of
using them through the Open Firmware backdoor.
- Rename platform_chrp to platform_powermac since it has become
increasingly Powermac specific. When we gain support for IBM systems,
we will grow a new platform_chrp.
provide PCI devices for various hardware such as memory controllers, etc.
These PCI buses are not enumerated via ACPI however. Add qpi(4) psuedo
bus and Host-PCI bridge drivers to enumerate these buses. Currently the
driver uses the CPU ID to determine the bridges' presence.
In collaboration with: Joseph Golio @ Isilon Systems
MFC after: 2 weeks
Makefiles or *.mk files, use ${CC:T:Mfoo} instead, so only the basename
of the compiler command (excluding any arguments) is considered.
This allows you to use, for example, CC="/nondefault/path/clang -xxx",
and still have the various tests in bsd.*.mk identify your compiler as
clang correctly.
ICC if cases were also changed.
Submitted by: Dimitry Andric <dimitry at andric.com>
As des noted, the section on SCTP would benefit from
a rewrite by a native speaker (which I am not).
Any volunteers?
Approved by: des (mentor)
MFC after: 1 week
zones for each malloc bucket size. The purpose is to isolate
different malloc types into hash classes, so that any buffer overruns
or use-after-free will usually only affect memory from malloc types in
that hash class. This is purely a debugging tool; by varying the hash
function and tracking which hash class was corrupted, the intersection
of the hash classes from each instance will point to a single malloc
type that is being misused. At this point inspection or memguard(9)
can be used to catch the offending code.
Add MALLOC_DEBUG_MAXZONES=8 to -current GENERIC configuration files.
The suggestion to have this on by default came from Kostik Belousov on
-arch.
This code is based on work by Ron Steinke at Isilon Systems.
Reviewed by: -arch (mostly silence)
Reviewed by: zml
Approved by: zml (mentor)
module that can be used by both the regular and experimental nfs
clients. This fixes the problem reported by jh@ where /dev/nfslock
would be registered twice when both nfs clients were used.
I also defined the size of the lm_fh field to be the correct value,
as it should be the maximum size of an NFSv3 file handle.
Reviewed by: jh
MFC after: 2 weeks
The aeskeys_{amd64,i386}.S content was mostly obtained from OpenBSD,
no objections to the license from core.
Hardware provided by: Sentex Communications
Tested by: fabient, pho (previous versions)
MFC after: 1 month
library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
which improperly uses an evaluation board's board number and breaks board
detection at runtime. This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO
ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
structures where possible (it would be advisable to use the Simple Executive
API to set the PIO mode, too, but that is not done presently.) Also use
structures from FreeBSD's ATA layer rather than structures copied from
Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
and writes to 64-bit addresses and use its macros for various device
addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
Cavium-provided code originally written for Linux. Also make it use the
same simplified test that the Simple Executive and Linux both use rather
than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
the kernel, rather than assuming we know which addresses we can steal.
NB: This may reduce the amount of RAM the kernel reports you as having if
you are leaving large temporary allocations made by U-Boot allocated
when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes
Ethernet interface naming from rgmxN to octeN. The new driver has vast
improvements over the old one, both in performance and functionality, but
does still have some features which have not been ported entirely and there
may be unimplemented code that can be hit in everyday use. I will make
every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
executive-config.h or cvmx-config.h. In the future we may want to
revert part of these changes and supply executive-config.h and
cvmx-config.h and access to the options contained in those files via
kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
of the USB PID.
MACHINE_CPUARCH isn't defined. I believe that this will cover all
options.
I didn't define it in kern.mk because $M is set to MACHINE_CPUARCH and
then is expanded for the genassym.o rule in kern.post.mk and kern.mk
is included after this, so the expansion isn't quite right. I think
this is a bug in make, but don't have the time to track it to ground
(and even if I did, fixing it would require a MFC of the change to the
very old systems we're targetting with this fix).
Kernel sources for 64-bit PowerPC, along with build-system changes to keep
32-bit kernels compiling (build system changes for 64-bit kernels are
coming later). Existing 32-bit PowerPC kernel configurations must be
updated after this change to specify their architecture.
(exec_setregs, etc.) in order to simplify the addition of 64-bit support,
and possible future extension of the Book-E code to handle hard floating
point and Altivec.
MFC after: 1 month
The following systems are affected:
- MPC8555CDS
- MPC8572DS
This overhaul covers the following major changes:
- All integrated peripherals drivers for Freescale MPC85XX SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- This includes: LBC, PCI / PCI-Express, I2C, DS1553, OpenPIC, TSEC, SEC,
QUICC, UART, CFI.
- Thanks to the common FDT infrastrucutre (fdtbus, simplebus) we retire
ocpbus(4) driver, which was based on hard-coded config data.
Note that world for these platforms has to be built WITH_FDT.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
the core changes but left out the shared code, lol.
Well, and a couple fixes to the core... hopefully
this will all be complete now.
Happy happy joy joy :)
It has more features than acpi_aiboost(4) and it will eventually replace
acpi_aiboost(4).
Submitted by: Constantine A. Murenin <cnst at FreeBSD.org>
Reviewed by: freebsd-acpi, imp
MFC after: 1 month
