would turn off all fans when initializing a zone. However, the HP Omnibook
500 generates a notify saying the zone needs to be re-evaluated whenever
its fan is switched on or off. This produced an infinite loop. Also, note
that running _SCP can generate the same notify.
Since we need to make sure old fan references are turned off when getting
new ones, run acpi_tz_monitor() first. This will turn off any unneeded
fans. Then, check for new settings. After that, run acpi_tz_monitor()
again to turn on/off any fans referenced by the new settings.
Tested by: brooks
returned and then infer the state from calls to _ON/_OFF. This works
around a problem in systems that don't correctly report the state (i.e.
the HP Omnibook 500 reports "on" for its fan always after it has been
turned on once).
unless ACPI_DEBUG is defined. Users don't typically care about errant
breakpoint instructions. The HP Pavilion 7915 has this in its PCI0
_INI method for rev 0x6040000 of the RSDT.
should only affect current resources, it seems best to wait until all
configuration is done before disabling it. If this fixes any problems, it
is a MT5 candidate.
hold its own values, pass them up to the parent (acpi0) and merge/uniq them
on the way. After the namespace evaluation, acpi will reserve these
resources and manage them via rman before bus_generic_probe() and
bus_generic_attach(). This is necessary because some systems specify
conflicting resources in separate sysresource objects. It's also cleaner
in that the interface between sysresource and acpi is now merely the parent's
resource list. This code handles the following cases:
1. Unique resource: add it to the parent via bus_set_resource().
2. New wholly contained in old: discard new.
3. New tail overlaps old head: grow old head downward.
AND/OR
4. New head overlaps old tail: grow old tail upward.
Tested by: Pawel Worach <sajd_at_telia.com>
Tested by: Radek Kozlowski <radek_at_raadradd.com>
MFC after: 5 days
systems that have overlapping regions specified in their sysresource
objects. This patch fixes ATA DMA and acpi_timer allocation for such
sysctems. It should eventually be moved to resource_list_add() if it is
a valid generalized approach. The minimal approach for 5.3 is:
"Loop through all current resources to see if the new one overlaps
any existing ones. If so, the old one always takes precedence and
the new one is adjusted (or rejected). We check for three cases:
1. Tail of new resource overlaps head of old resource: truncate the
new resource so it is contiguous with the start of the old.
2. New resource wholly contained within the old resource: error.
3. Head of new resource overlaps tail of old resource: truncate the
new resource so it is contiguous, following the old."
Tested by: Radek Kozlowski <radek_at_raadradd.com>
Discussed with: imp
MFC after: 4 days
callers. These ioctls attempted to enable and disable the ACPI
interpreter at runtime. In practice, it is not possible to boot with
ACPI and then disable it on many systems and trying to do so can cause
crashes, interrupt storms, etc. Binary compatibility with userland is
retained.
MFC after: 2 days
also generates a notify. Since we held the lock over this call, the
notify never got to run and the battery status read never returned.
Document this also.
Tested by: Maxim Maximov <mcsi_at_mcsi.pp.ru>
Approved by: re (scottl)
* Remove the interrupt wrapper that locked Giant and call the handler
directly. Mark the handler as MPSAFE.
* Don't attempt to detect if a handler is installed. Leave that to the
bus_alloc_resource() function.
* Serialize operations in acpi_video_bind_outputs(), acpi_video_detach(),
acpi_video_notify_handler(), acpi_video_power_profile(), and the sysctls.
The main goal is to protect the shared device list and prevent conflicting
settings.
* Add assertions that the sx lock is held in the leaf functions.
* Restructure the event handling path. acpi_tz_thread() now calls
acpi_tz_timeout() any time an event occurs. acpi_tz_timeout() checks
the flags and calls acpi_tz_power_profile(), acpi_tz_establish(), and
acpi_tz_monitor() as appropriate. Notifies only do a wakeup and let
acpi_tz_thread() do the actual work. This path is cleaner and allows
locking since the call path is now always a D.A.G.
* Add the acpi_tz_signal() function to set flags and wake the thread.
* Remove the tz_tmp_updating flag since calls are serialized by
acpi_tz_thread().
* Remove Giant locking.
* Serialize acpi_pwr_switch_consumer() and acpi_pwr_wake_enable().
* Make acpi_pwr_switch_consumer() have a single exit point.
* Add assertions to the leaf functions they call.
* Fix a memory leak in acpi_pwr_deregister_consumer(). However, it is
currently ifdefed out so this code was unused.
* Serialize access to acpi_pci_link_config(), acpi_pci_find_prt(),
acpi_pci_link_route(), and acpi_pci_link_resume().
* Add lock assertions to all functions called by them.
* Serialize notifying the user in acpi_lid_notify_status_changed(). This
way multiple lid events occur in order.
* Add an initialization pass to get the lid status at boot-time. This
pass does not notify any apps but gets the initial status.
* Use the common serialization macros instead of rolling our own.
* Increase the coverage of the lock in EcSpaceHandler() to cover the entire
loop to avoid dropping the lock when reading more than one byte.
* Serialize ops in acpi_cmbat_notify_handler(), acpi_cmbat_ioctl(),
acpi_cmbat_init_battery(), and acpi_cmbat_get_battinfo().
* Get the softc directly in acpi_cmbat_get_total_battinfo() rather than
build an array of them.
* Don't queue a _BIF query after receiving a notify. Since we clear the
timespec, a _BIF query will be done in the context of the next caller.
* Add asserts to leaf functions that operate on shared data.
* Remove the bst/bif updating flags now that we hold the lock over the
full query.
* Explain various comments in more detail.
* Serialize acpi_battery_get_battdesc(), acpi_battery_register(), and
acpi_battery_remove().
* Assert that the sx lock is held in acpi_batteries_init().
* Remove check for device_get_softc() returning NULL.
* Serialize notification of acline changes in acpi_acad_get_status().
* Remove the initializing flag. With the locking, we don't need to
push off requests for the acline before initialization is done.
* Don't check device_get_softc(), it can't return NULL.
* Serialize calls to acpi_alloc_resource(), acpi_release_resource(),
acpi_Enable(), acpi_Disable(), and acpi_debug_sysctl().
* Acquire the ACPI mutex in acpi_register_ioctl(), acpi_deregister_ioctl(),
and acpiioctl().
* Acquire the mutex while disabling subsequent requests to enter a
sleep state in acpi_SetSleepState().
* Be sure to re-enable sleep requests and don't run resume methods when
the current request fails.
* Don't check if sleep requests are disabled in the ACPIIO_SETSLPSTATE
ioctl. acpi_SetSleepState() does this for us.
* Remove the acquisition of Giant from the struct cdevsw.
* Remove the ACPI_USE_THREADS option.
* Add and comment our locking primitives. The mutex primitives use a
a static mutex and the serialization ones use a static sx lock. A global
acpi_mutex is used for access to global resources (i.e., writes to the
SMI_CMD register.)
* Remove 4.x compat defines.
there is no irq link. Since we now use the stored copy of PRT, not the
one that used to be passed into acpi_pcib_route_interrupt(), we need it in
the list. [1]
Fix a bug in acpi_pci_find_prt() where we weren't checking the bus, thus
choosing the wrong PRT entry to use for routing the link. Also, add a
printf for the case where the PRT entry is not found as this should not
happen.
Tested by: marcel [1]
incomplete in that the PRT routing was not aware of link programming.
Fix this by doing all routing through the link devices. The new algorithm
for setting up links is:
1. Read _CRS to get current setting. If invalid (not in _PRS), then set
to 0.
2. Attempt to call _DIS on the link. If successful, mark the link as not
routed. Otherwise, assume it still is.
Then when a routing request occurs:
3. Update weights for all IRQs
4. Attempt to route the initial IRQ if valid
5. If that fails, walk through the sorted list, attempting to route IRQs.
6. Configure the trigger/polarity based on _PRS.
Other changes:
* Add acpi_pci_find_prt() to look up the PRT entry for a given device and
acpi_pci_link_route() to select/route the best IRQ for it.
* Remove duplicated code in acpi_pcib_route_interrupt() that picked the
first IRQ from _PRS.
* Remove unneeded arguments from acpi_pcib_resume() and friends.
* Ignore _STA on link devices but report if it seems strange.
* Add a prt_source handle to the PRT structure since the ACPI struct
ACPI_PCI_ROUTING_TABLE uses a fixed-size entry for it. We'll need to
dynamically size this object if we want to use it the same way ACPI-CA
does. Null-terminate the source.
Tested by: Luo Hong <luohong99_at_mails.tsinghua.edu.cn>,
Jeffrey Katcher <jmkatcher_at_yahoo.com>
Info from: jhb, Len Brown (Intel)
message if they are incorrect. Also, remove the hack of allowing the
initial irq setting to not be in _PRS. As before, the old behavior can be
regained by defining ACPI_OLD_PCI_LINK.
