do on i386. The consequences of not doing so on amd64 became apparent
with the introduction of the COUNT_IPIS and COUNT_XINVLTLB_HITS
options. Specifically, single-threaded applications were generating
unnecessary IPIs to shoot-down the TLB on other processors. However,
this is clearly nonsensical because a single-threaded application is
only running on the current processor. The reason that this happens
is that pmap_activate() is unable to properly update the old pmap's
field "pm_active" without the correct "curpmap". So, in effect, stale
bits in "pm_active" were leading pmap_protect(), pmap_remove(),
pmap_remove_pages(), etc. to flush the TLB contents on some arbitrary
processor that wasn't even running the same application.
Reviewed by: kib
MFC after: 3 weeks
ABI specifies the DF should be zero, and newer compilers do not clear
DF before using DF-sensitive instructions.
The DF clearing for signal handlers was done some time ago.
MFC after: 1 week
get_fpcontext(), and npxsetuserregs() for set_fpcontext). Also,
note that usercontext is not initialized anymore in fpstate_drop().
Systematically replace references to npxgetregs() and npxsetregs()
by npxgetuserregs() and npxsetuserregs() in comments.
Noted by: bde
writing event timer drivers, for choosing best possible drivers by machine
independent code and for operating them to supply kernel with hardclock(),
statclock() and profclock() events in unified fashion on various hardware.
Infrastructure provides support for both per-CPU (independent for every CPU
core) and global timers in periodic and one-shot modes. MI management code
at this moment uses only periodic mode, but one-shot mode use planned for
later, as part of tickless kernel project.
For this moment infrastructure used on i386 and amd64 architectures. Other
archs are welcome to follow, while their current operation should not be
affected.
This patch updates existing drivers (i8254, RTC and LAPIC) for the new
order, and adds event timers support into the HPET driver. These drivers
have different capabilities:
LAPIC - per-CPU timer, supports periodic and one-shot operation, may
freeze in C3 state, calibrated on first use, so may be not exactly precise.
HPET - depending on hardware can work as per-CPU or global, supports
periodic and one-shot operation, usually provides several event timers.
i8254 - global, limited to periodic mode, because same hardware used also
as time counter.
RTC - global, supports only periodic mode, set of frequencies in Hz
limited by powers of 2.
Depending on hardware capabilities, drivers preferred in following orders,
either LAPIC, HPETs, i8254, RTC or HPETs, LAPIC, i8254, RTC.
User may explicitly specify wanted timers via loader tunables or sysctls:
kern.eventtimer.timer1 and kern.eventtimer.timer2.
If requested driver is unavailable or unoperational, system will try to
replace it. If no more timers available or "NONE" specified for second,
system will operate using only one timer, multiplying it's frequency by few
times and uing respective dividers to honor hz, stathz and profhz values,
set during initial setup.
This information can be very valuable for CPU sleep-time (and respectively
idle power consumption) optimization.
Add counters for timer-related IPIs.
Reviewed by: jhb@ (previous version)
the consistency between PCPU fpcurthread and the state of the FPU.
Explicitely assert that the calling conventions for fpudrop() are
adhered too. In cpu_thread_exit(), add missed critical section entrance.
Reviewed by: bde
Tested by: pho
MFC after: 1 month
allow pmap_enter() to be performed on an unmanaged page that doesn't have
VPO_BUSY set. Having VPO_BUSY set really only matters for managed pages.
(See, for example, pmap_remove_write().)
in Linux emulation layer. Linux seems to only require that pos is
page-aligned, but otherwise ignores it. Default FreeBSD mmap parameter
checking is too strict to allow some Linux binaries to run. tsMuxeR is
one example of such a binary.
Discussed with: jhb
MFC after: 1 week
PG_REFERENCED changes in vm_pageout_object_deactivate_pages().
Simplify this function's inner loop using TAILQ_FOREACH(), and shorten
some of its overly long lines. Update a stale comment.
Assert that PG_REFERENCED may be cleared only if the object containing
the page is locked. Add a comment documenting this.
Assert that a caller to vm_page_requeue() holds the page queues lock,
and assert that the page is on a page queue.
Push down the page queues lock into pmap_ts_referenced() and
pmap_page_exists_quick(). (As of now, there are no longer any pmap
functions that expect to be called with the page queues lock held.)
Neither pmap_ts_referenced() nor pmap_page_exists_quick() should ever
be passed an unmanaged page. Assert this rather than returning "0"
and "FALSE" respectively.
ARM:
Simplify pmap_page_exists_quick() by switching to TAILQ_FOREACH().
Push down the page queues lock inside of pmap_clearbit(), simplifying
pmap_clear_modify(), pmap_clear_reference(), and pmap_remove_write().
Additionally, this allows for avoiding the acquisition of the page
queues lock in some cases.
PowerPC/AIM:
moea*_page_exits_quick() and moea*_page_wired_mappings() will never be
called before pmap initialization is complete. Therefore, the check
for moea_initialized can be eliminated.
Push down the page queues lock inside of moea*_clear_bit(),
simplifying moea*_clear_modify() and moea*_clear_reference().
The last parameter to moea*_clear_bit() is never used. Eliminate it.
PowerPC/BookE:
Simplify mmu_booke_page_exists_quick()'s control flow.
Reviewed by: kib@
the interrupt followed by a brief delay if it is not currently masked
before moving the interrupt.
- Move the icu_lock out of ioapic_program_intpin() and into callers. This
closes a race where ioapic_program_intpin() could use a stale value of
the masked state to compute the masked bit in the register.
Reviewed by: mav
MFC after: 2 weeks
FPU/SSE hardware. Caller should provide a save area that is chained
into the stack of the areas; pcb save_area for usermode FPU state is
on top. The pcb now contains a pointer to the current FPU saved area,
used during FPUDNA handling and context switches. There is also a
facility to allow the kernel thread to use pcb save_area.
Change the dreaded warnings "npxdna in kernel mode!" into the panics
when FPU usage is not registered.
KPI discussed with: fabient
Tested by: pho, fabient
Hardware provided by: Sentex Communications
MFC after: 1 month
an ordering dependence: A pmap operation that clears PG_WRITEABLE and calls
vm_page_dirty() must perform the call first. Otherwise, pmap_is_modified()
could return FALSE without acquiring the page queues lock because the page
is not (currently) writeable, and the caller to pmap_is_modified() might
believe that the page's dirty field is clear because it has not seen the
effect of the vm_page_dirty() call.
When I pushed down the page queues lock into pmap_is_modified(), I
overlooked one place where this ordering dependence is violated:
pmap_enter(). In a rare situation pmap_enter() can be called to replace a
dirty mapping to one page with a mapping to another page. (I say rare
because replacements generally occur as a result of a copy-on-write fault,
and so the old page is not dirty.) This change delays clearing PG_WRITEABLE
until after vm_page_dirty() has been called.
Fixing the ordering dependency also makes it easy to introduce a small
optimization: When pmap_enter() used to replace a mapping to one page with a
mapping to another page, it freed the pv entry for the first mapping and
later called the pv entry allocator for the new mapping. Now, pmap_enter()
attempts to recycle the old pv entry, saving two calls to the pv entry
allocator.
There is no point in setting PG_WRITEABLE on unmanaged pages, so don't.
Update a comment to reflect this.
Tidy up the variable declarations at the start of pmap_enter().
pmap_is_referenced(). Eliminate the corresponding page queues lock
acquisitions from vm_map_pmap_enter() and mincore(), respectively. In
mincore(), this allows some additional cases to complete without ever
acquiring the page queues lock.
Assert that the page is managed in pmap_is_referenced().
On powerpc/aim, push down the page queues lock acquisition from
moea*_is_modified() and moea*_is_referenced() into moea*_query_bit().
Again, this will allow some additional cases to complete without ever
acquiring the page queues lock.
Reorder a few statements in vm_page_dontneed() so that a race can't lead
to an old reference persisting. This scenario is described in detail by a
comment.
Correct a spelling error in vm_page_dontneed().
Assert that the object is locked in vm_page_clear_dirty(), and restrict the
page queues lock assertion to just those cases in which the page is
currently writeable.
Add object locking to vnode_pager_generic_putpages(). This was the one
and only place where vm_page_clear_dirty() was being called without the
object being locked.
Eliminate an unnecessary vm_page_lock() around vnode_pager_setsize()'s call
to vm_page_clear_dirty().
Change vnode_pager_generic_putpages() to the modern-style of function
definition. Also, change the name of one of the parameters to follow
virtual memory system naming conventions.
Reviewed by: kib
APIC interrupt that fires when a threshold of corrected machine check
events is reached. CMCI also includes a count of events when reporting
corrected errors in the bank's status register. Note that individual
banks may or may not support CMCI. If they do, each bank includes its own
threshold register that determines when the interrupt fires. Currently
the code uses a very simple strategy where it doubles the threshold on
each interrupt until it succeeds in throttling the interrupt to occur
only once a minute (this interval can be tuned via sysctl). The threshold
is also adjusted on each hourly poll which will lower the threshold once
events stop occurring.
Tested by: Sailaja Bangaru sbappana at yahoo com
MFC after: 1 month
independent code. Move this code into mincore(), and eliminate the
page queues lock from pmap_mincore().
Push down the page queues lock into pmap_clear_modify(),
pmap_clear_reference(), and pmap_is_modified(). Assert that these
functions are never passed an unmanaged page.
Eliminate an inaccurate comment from powerpc/powerpc/mmu_if.m:
Contrary to what the comment says, pmap_mincore() is not simply an
optimization. Without a complete pmap_mincore() implementation,
mincore() cannot return either MINCORE_MODIFIED or MINCORE_REFERENCED
because only the pmap can provide this information.
Eliminate the page queues lock from vfs_setdirty_locked_object(),
vm_pageout_clean(), vm_object_page_collect_flush(), and
vm_object_page_clean(). Generally speaking, these are all accesses
to the page's dirty field, which are synchronized by the containing
vm object's lock.
Reduce the scope of the page queues lock in vm_object_madvise() and
vm_page_dontneed().
Reviewed by: kib (an earlier version)
arbitrary frequencies into hardclock(), statclock() and profclock() calls.
Same code with minor variations duplicated several times over the tree for
different timer drivers and architectures.
- Switch all x86 archs to new functions, simplifying the code and removing
extra logic from timer drivers. Other archs are also welcome.
Extend struct sysvec with three new elements:
sv_fetch_syscall_args - the method to fetch syscall arguments from
usermode into struct syscall_args. The structure is machine-depended
(this might be reconsidered after all architectures are converted).
sv_set_syscall_retval - the method to set a return value for usermode
from the syscall. It is a generalization of
cpu_set_syscall_retval(9) to allow ABIs to override the way to set a
return value.
sv_syscallnames - the table of syscall names.
Use sv_set_syscall_retval in kern_sigsuspend() instead of hardcoding
the call to cpu_set_syscall_retval().
The new functions syscallenter(9) and syscallret(9) are provided that
use sv_*syscall* pointers and contain the common repeated code from
the syscall() implementations for the architecture-specific syscall
trap handlers.
Syscallenter() fetches arguments, calls syscall implementation from
ABI sysent table, and set up return frame. The end of syscall
bookkeeping is done by syscallret().
Take advantage of single place for MI syscall handling code and
implement ptrace_lwpinfo pl_flags PL_FLAG_SCE, PL_FLAG_SCX and
PL_FLAG_EXEC. The SCE and SCX flags notify the debugger that the
thread is stopped at syscall entry or return point respectively. The
EXEC flag augments SCX and notifies debugger that the process address
space was changed by one of exec(2)-family syscalls.
The i386, amd64, sparc64, sun4v, powerpc and ia64 syscall()s are
changed to use syscallenter()/syscallret(). MIPS and arm are not
converted and use the mostly unchanged syscall() implementation.
Reviewed by: jhb, marcel, marius, nwhitehorn, stas
Tested by: marcel (ia64), marius (sparc64), nwhitehorn (powerpc),
stas (mips)
MFC after: 1 month
DDB so that all the fields line up.
- Print out the tid of the per-CPU idlethread instead of the pid since
the idle process is now shared across all idle threads.
MFC after: 1 month
here, make the style of assertion used by pmap_enter() consistent
across all architectures.
On entry to pmap_remove_write(), assert that the page is neither
unmanaged nor fictitious, since we cannot remove write access to
either kind of page.
With the push down of the page queues lock, pmap_remove_write() cannot
condition its behavior on the state of the PG_WRITEABLE flag if the
page is busy. Assert that the object containing the page is locked.
This allows us to know that the page will neither become busy nor will
PG_WRITEABLE be set on it while pmap_remove_write() is running.
Correct a long-standing bug in vm_page_cowsetup(). We cannot possibly
do copy-on-write-based zero-copy transmit on unmanaged or fictitious
pages, so don't even try. Previously, the call to pmap_remove_write()
would have failed silently.
labeled iretq instruction.
Suppose that multithreaded process executes two threads, currently
scheduled on different processors. Let assume that thread A executes
using %cs or %ss pointing into the descriptor from LDT. If IPI comes
which handler does not return by jump to doreti, and meantime thread B
invalidates descriptor pointed to by %cs or %ss, then iretq from IPI
handler could fault.
Routing the return by doreti_iret allows kernel to catch the situation
and recover from it by sending signal to the usermode.
Tested by: pho
MFC after: 1 week
frame upon segment register load fault. The doreti procedure does not
load segment registers when returning to the kernel frame, and current
values in the segment descriptor cache already allow the kernel mode
to run, not modified by faulted loaded.
Suggested by: bde
Tested by: pho
MFC after: 1 week
vm_page_try_to_free(). Consequently, push down the page queues lock into
pmap_enter_quick(), pmap_page_wired_mapped(), pmap_remove_all(), and
pmap_remove_write().
Push down the page queues lock into Xen's pmap_page_is_mapped(). (I
overlooked the Xen pmap in r207702.)
Switch to a per-processor counter for the total number of pages cached.
