The implementation of the Kernel Page Table Isolation (KPTI) for
amd64, first version. It provides a workaround for the 'meltdown'
vulnerability. PTI is turned off by default for now, enable with the
loader tunable vm.pmap.pti=1.
The pmap page table is split into kernel-mode table and user-mode
table. Kernel-mode table is identical to the non-PTI table, while
usermode table is obtained from kernel table by leaving userspace
mappings intact, but only leaving the following parts of the kernel
mapped:
kernel text (but not modules text)
PCPU
GDT/IDT/user LDT/task structures
IST stacks for NMI and doublefault handlers.
Kernel switches to user page table before returning to usermode, and
restores full kernel page table on the entry. Initial kernel-mode
stack for PTI trampoline is allocated in PCPU, it is only 16
qwords. Kernel entry trampoline switches page tables. then the
hardware trap frame is copied to the normal kstack, and execution
continues.
IST stacks are kept mapped and no trampoline is needed for
NMI/doublefault, but of course page table switch is performed.
On return to usermode, the trampoline is used again, iret frame is
copied to the trampoline stack, page tables are switched and iretq is
executed. The case of iretq faulting due to the invalid usermode
context is tricky, since the frame for fault is appended to the
trampoline frame. Besides copying the fault frame and original
(corrupted) frame to kstack, the fault frame must be patched to make
it look as if the fault occured on the kstack, see the comment in
doret_iret detection code in trap().
Currently kernel pages which are mapped during trampoline operation
are identical for all pmaps. They are registered using
pmap_pti_add_kva(). Besides initial registrations done during boot,
LDT and non-common TSS segments are registered if user requested their
use. In principle, they can be installed into kernel page table per
pmap with some work. Similarly, PCPU can be hidden from userspace
mapping using trampoline PCPU page, but again I do not see much
benefits besides complexity.
PDPE pages for the kernel half of the user page tables are
pre-allocated during boot because we need to know pml4 entries which
are copied to the top-level paging structure page, in advance on a new
pmap creation. I enforce this to avoid iterating over the all
existing pmaps if a new PDPE page is needed for PTI kernel mappings.
The iteration is a known problematic operation on i386.
The need to flush hidden kernel translations on the switch to user
mode make global tables (PG_G) meaningless and even harming, so PG_G
use is disabled for PTI case. Our existing use of PCID is
incompatible with PTI and is automatically disabled if PTI is
enabled. PCID can be forced on only for developer's benefit.
MCE is known to be broken, it requires IST stack to operate completely
correctly even for non-PTI case, and absolutely needs dedicated IST
stack because MCE delivery while trampoline did not switched from PTI
stack is fatal. The fix is pending.
Reviewed by: markj (partially)
Tested by: pho (previous version)
Discussed with: jeff, jhb
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Upon successful completion, the execve() system call invokes
exec_setregs() to initialize the registers of the initial thread of the
newly executed process. What is weird is that when execve() returns, it
still goes through the normal system call return path, clobbering the
registers with the system call's return value (td->td_retval).
Though this doesn't seem to be problematic for x86 most of the times (as
the value of eax/rax doesn't matter upon startup), this can be pretty
frustrating for architectures where function argument and return
registers overlap (e.g., ARM). On these systems, exec_setregs() also
needs to initialize td_retval.
Even worse are architectures where cpu_set_syscall_retval() sets
registers to values not derived from td_retval. On these architectures,
there is no way cpu_set_syscall_retval() can set registers to the way it
wants them to be upon the start of execution.
To get rid of this madness, let sys_execve() return EJUSTRETURN. This
will cause cpu_set_syscall_retval() to leave registers intact. This
makes process execution easier to understand. It also eliminates the
difference between execution of the initial process and successive ones.
The initial call to sys_execve() is not performed through a system call
context.
Reviewed by: kib, jhibbits
Differential Revision: https://reviews.freebsd.org/D13180
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
Initially, only tag files that use BSD 4-Clause "Original" license.
RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133
struct thread.
For all architectures, the syscall trap handlers have to allocate the
structure on the stack. The structure takes 88 bytes on 64bit arches
which is not negligible. Also, it cannot be easily found by other
code, which e.g. caused duplication of some members of the structure
to struct thread already. The change removes td_dbg_sc_code and
td_dbg_sc_nargs which were directly copied from syscall_args.
The structure is put into the copied on fork part of the struct thread
to make the syscall arguments information correct in the child after
fork.
This move will also allow several more uses shortly.
Reviewed by: jhb (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
X-Differential revision: https://reviews.freebsd.org/D11080
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
POSIX requires these members to be of type void * rather than the
char * inherited from 4BSD. NetBSD and OpenBSD both changed their
fields to void * back in 1998. No new build failures were reported
via an exp-run.
PR: 206503 (exp-run)
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D5092
buildkernel run.
Some of them were write-only under some kernel options, e.g. variables
keeping values only used by CTR() macros. It costs nothing to the
code readability and correctness to eliminate the warnings in those
cases too by removing the local cached values used only for
single-access.
Review: https://reviews.freebsd.org/D2665
Reviewed by: rodrigc
Looked at by: bjk
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Native ABI do not need signal conversion, only emulators may want this. Usually
emulators implements its own sv_sendsig method. For now only ibcs2 emulator does
not have own sv_sendsig implementation and depends on native sendsig() method.
So, remove any extra attempts to convert signal numbers from native sendsig()
methods except from i386 where ibsc2 is living.
const. On x86, even after the machine context is supposedly read into
the struct ucontext, lazy FPU state save code might only mark the FPU
data as hardware-owned. Later, set_fpcontext() needs to fetch the
state from hardware, modifying the *mcp.
The set_mcontext(9) is called from sigreturn(2) and setcontext(2)
implementations and old create_thread(2) interface, which throw the
*mcp out after the set_mcontext() call.
Reported by: dim
Discussed with: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
setting call gate, which must be 64 bit, put a code segment descriptor
into ldt slot 0.
This way, syscall shim does not switch temporary to 64bit trampoline,
and does not create a window where signal delivery interrupts 64 bit
mode (signal handler cannot return). The cost is shim running with
non-zero based segment in %cs, which requires vfork() handling make
more assumptions.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Debuggers may need to change PSL_RF. Note that tf_eflags is already stored
in the signal context during signal handling and PSL_RF previously could be
modified via sigreturn, so this change should not provide any new ability
to userspace.
For background see the thread at:
http://lists.freebsd.org/pipermail/freebsd-i386/2007-September/005910.html
Reviewed by: jhb, kib
Sponsored by: DARPA, AFRL
value on purpose, but the ia32 context handling code is logically more
correct to use the _MC_IA32_HASFPXSTATE name for the flag.
Tested by: dim, pgj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
usermode context state is not changed by the get operation, and
get_mcontext() does not require full iret as well.
Tested by: dim, pgj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
in long mode which transfers control to 32bit code segment. Unbreak
the lcall $7,$0 implementation on amd64 by putting the 64bit user code
segment' selector into call gate, and execute the 64bit trampoline
which converts the return frame into 32bit format and switches back to
32bit mode for executing int $0x80 trampoline.
Note that all jumps over the hoops are performed in the user mode.
MFC after: 1 week
64bit and 32bit ABIs. As a side-effect, it enables AVX on capable
CPUs.
In particular:
- Query the CPU support for XSAVE, list of the supported extensions
and the required size of FPU save area. The hw.use_xsave tunable is
provided for disabling XSAVE, and hw.xsave_mask may be used to
select the enabled extensions.
- Remove the FPU save area from PCB and dynamically allocate the
(run-time sized) user save area on the top of the kernel stack,
right above the PCB. Reorganize the thread0 PCB initialization to
postpone it after BSP is queried for save area size.
- The dumppcb, stoppcbs and susppcbs now do not carry the FPU state as
well. FPU state is only useful for suspend, where it is saved in
dynamically allocated suspfpusave area.
- Use XSAVE and XRSTOR to save/restore FPU state, if supported and
enabled.
- Define new mcontext_t flag _MC_HASFPXSTATE, indicating that
mcontext_t has a valid pointer to out-of-struct extended FPU
state. Signal handlers are supplied with stack-allocated fpu
state. The sigreturn(2) and setcontext(2) syscall honour the flag,
allowing the signal handlers to inspect and manipilate extended
state in the interrupted context.
- The getcontext(2) never returns extended state, since there is no
place in the fixed-sized mcontext_t to place variable-sized save
area. And, since mcontext_t is embedded into ucontext_t, makes it
impossible to fix in a reasonable way. Instead of extending
getcontext(2) syscall, provide a sysarch(2) facility to query
extended FPU state.
- Add ptrace(2) support for getting and setting extended state; while
there, implement missed PT_I386_{GET,SET}XMMREGS for 32bit binaries.
- Change fpu_kern KPI to not expose struct fpu_kern_ctx layout to
consumers, making it opaque. Internally, struct fpu_kern_ctx now
contains a space for the extended state. Convert in-kernel consumers
of fpu_kern KPI both on i386 and amd64.
First version of the support for AVX was submitted by Tim Bird
<tim.bird am sony com> on behalf of Sony. This version was written
from scratch.
Tested by: pho (previous version), Yamagi Burmeister <lists yamagi org>
MFC after: 1 month
In particular:
- implement compat shims for old stat(2) variants and ogetdirentries(2);
- implement delivery of signals with ancient stack frame layout and
corresponding sigreturn(2);
- implement old getpagesize(2);
- provide a user-mode trampoline and LDT call gate for lcall $7,$0;
- port a.out image activator and connect it to the build as a module
on amd64.
The changes are hidden under COMPAT_43.
MFC after: 1 month
MI ucontext_t and x86 MD parts.
Kernel allocates the structures on the stack, and not clearing
reserved fields and paddings causes leakage.
Noted and discussed with: bde
MFC after: 2 weeks
setting SV_SHP flag and providing pointer to the vm object and mapping
address. Provide simple allocator to carve space in the page, tailored
to put the code with alignment restrictions.
Enable shared page use for amd64, both native and 32bit FreeBSD
binaries. Page is private mapped at the top of the user address
space, moving a start of the stack one page down. Move signal
trampoline code from the top of the stack to the shared page.
Reviewed by: alc
for manipulating pcb_flags. These inline functions are very similar to
atomic_set_char(9) and atomic_clear_char(9) but without unnecessary LOCK
prefix for SMP. Add comments about the rationale[1]. Use these functions
wherever possible. Although there are some places where it is not strictly
necessary (e.g., a PCB is copied to create a new PCB), it is done across
the board for sake of consistency. Turn pcb_full_iret into a PCB flag as
it is safe now. Move rarely used fields before pcb_flags and reduce size
of pcb_flags to one byte. Fix some style(9) nits in pcb.h while I am in
the neighborhood.
Reviewed by: kib
Submitted by: kib[1]
MFC after: 2 months
functions, they are unused. Remove 'user' from npxgetuserregs()
etc. names.
For {npx,fpu}{get,set}regs(), always use pcb->pcb_user_save for FPU
context storage. This eliminates the need for ugly copying with
overwrite of the newly added and reserved fields in ucontext on i386
to satisfy alignment requirements for fpusave() and fpurstor().
pc98 version was copied from i386.
Suggested and reviewed by: bde
Tested by: pho (i386 and amd64)
MFC after: 1 week
ABI specifies the DF should be zero, and newer compilers do not clear
DF before using DF-sensitive instructions.
The DF clearing for signal handlers was done some time ago.
MFC after: 1 week
FPU/SSE hardware. Caller should provide a save area that is chained
into the stack of the areas; pcb save_area for usermode FPU state is
on top. The pcb now contains a pointer to the current FPU saved area,
used during FPUDNA handling and context switches. There is also a
facility to allow the kernel thread to use pcb save_area.
Change the dreaded warnings "npxdna in kernel mode!" into the panics
when FPU usage is not registered.
KPI discussed with: fabient
Tested by: pho, fabient
Hardware provided by: Sentex Communications
MFC after: 1 month
Extend struct sysvec with three new elements:
sv_fetch_syscall_args - the method to fetch syscall arguments from
usermode into struct syscall_args. The structure is machine-depended
(this might be reconsidered after all architectures are converted).
sv_set_syscall_retval - the method to set a return value for usermode
from the syscall. It is a generalization of
cpu_set_syscall_retval(9) to allow ABIs to override the way to set a
return value.
sv_syscallnames - the table of syscall names.
Use sv_set_syscall_retval in kern_sigsuspend() instead of hardcoding
the call to cpu_set_syscall_retval().
The new functions syscallenter(9) and syscallret(9) are provided that
use sv_*syscall* pointers and contain the common repeated code from
the syscall() implementations for the architecture-specific syscall
trap handlers.
Syscallenter() fetches arguments, calls syscall implementation from
ABI sysent table, and set up return frame. The end of syscall
bookkeeping is done by syscallret().
Take advantage of single place for MI syscall handling code and
implement ptrace_lwpinfo pl_flags PL_FLAG_SCE, PL_FLAG_SCX and
PL_FLAG_EXEC. The SCE and SCX flags notify the debugger that the
thread is stopped at syscall entry or return point respectively. The
EXEC flag augments SCX and notifies debugger that the process address
space was changed by one of exec(2)-family syscalls.
The i386, amd64, sparc64, sun4v, powerpc and ia64 syscall()s are
changed to use syscallenter()/syscallret(). MIPS and arm are not
converted and use the mostly unchanged syscall() implementation.
Reviewed by: jhb, marcel, marius, nwhitehorn, stas
Tested by: marcel (ia64), marius (sparc64), nwhitehorn (powerpc),
stas (mips)
MFC after: 1 month
about inacessible or wrong mcontext, and for dreaded "kernel trap with
interrupts disabled" situation. The later is changed when trap is
generated from user mode (shall never be ?).
Normalize the messages to include both pid and thread name.
MFC after: 1 week
to the image_params struct instead of several members of that struct
individually. This makes it easier to expand its arguments in the future
without touching all platforms.
Reviewed by: jhb
syscall arguments are collected before ptracestop() is called. As a
consequence, debugger cannot modify syscall or its arguments.
For i386, amd64 and ia32 on amd64 MD syscall(), reread syscall number
and arguments after ptracestop(), if debugger modified anything in the
process environment. Since procfs stopeven requires number of syscall
arguments in p_xstat, this cannot be solved by moving stop/trace point
before argument fetching.
Move the code to read arguments into separate function
fetch_syscall_args() to avoid code duplication. Note that ktrace point
for modified syscall is intentionally recorded twice, once with original
arguments, and second time with the arguments set by debugger.
PT_TO_SCX stop is executed after cpu_syscall_set_retval() already.
Reported by: Ali Polatel <alip exherbo org>
Briefly discussed with: jhb
MFC after: 3 weeks
while in kernel mode, and later changing signal mask to block the
signal, was fixed for sigprocmask(2) and ptread_exit(3). The same race
exists for sigreturn(2), setcontext(2) and swapcontext(2) syscalls.
Use kern_sigprocmask() instead of direct manipulation of td_sigmask to
reschedule newly blocked signals, closing the race.
Reviewed by: davidxu
Tested by: pho
MFC after: 1 month
return path only when neither thread was context switched while
executing syscall code nor syscall explicitely modified LDT or MSRs.
Save segment registers in trap handlers before interrupts are enabled,
to not allow context switches to happen before registers are saved.
Use separated byte in pcb for indication of fast/full return, since
pcb_flags are not synchronized with context switches.
The change puts back syscall microbenchmark numbers that were slowed
down after commit of the support for LDT on amd64.
Reviewed by: jeff
Tested (and tested, and tested ...) by: pho
Approved by: re (kensmith)
the kernel on amd64. Fill and read segment registers for mcontext and
signals. Handle traps caused by restoration of the
invalidated selectors.
Implement user-mode creation and manipulation of the process-specific
LDT descriptors for amd64, see sysarch(2).
Implement support for TSS i/o port access permission bitmap for amd64.
Context-switch LDT and TSS. Do not save and restore segment registers on
the context switch, that is handled by kernel enter/leave trampolines
now. Remove segment restore code from the signal trampolines for
freebsd/amd64, freebsd/ia32 and linux/i386 for the same reason.
Implement amd64-specific compat shims for sysarch.
Linuxolator (temporary ?) switched to use gsbase for thread_area pointer.
TODO:
Currently, gdb is not adapted to show segment registers from struct reg.
Also, no machine-depended ptrace command is added to set segment
registers for debugged process.
In collaboration with: pho
Discussed with: peter
Reviewed by: jhb
Linuxolator tested by: dchagin
