ratectl_node_init() functions and since ni_rtctls was already
malloc'ed() we will panic. Fix this by using the already malloc'ed
pointer.
Found by: bschmidt
Reviewed by: bschmidt
a revert call. In this case don't attempt to remove something that
has not yet been added. Otherwise this jaddref must hang around
to prevent the bitmap write as normal.
the page table entry's accessed bit is either preset by the immediately
preceding call to pmap_enter() or by hardware (or software) upon return
from vm_fault() when the faulting access is restarted.
or unmanaged before acquiring the page queues lock. Neither of these
tests require that lock. Moreover, a better way of testing if the page
is unmanaged is to test the type of vm object. This avoids a pointless
vm_page_lookup().
MFC after: 3 weeks
Open Firmware device tree in order to match what the PROM built-in
driver uses. This is especially important when netbooting Fujitsu
Siemens PRIMEPOWER250 as in that case the built-in driver isn't used
and the port facts PortSCSIID defaults to 0, conflicting with the
disk at the same address.
handler, as the latter is not guaranteed to be signal safe, and we
do not really care about flushing the stream during SIGINT.
Suggested by: Maxim Konovalov <maxim.konovalov gmail com>
MFC after: 13 days
Add missing CURVNET_RESTORE() calls for multiple code paths, to stop
leaking the currently cached vnet into callers and to the process.
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
MFC after: 4 days
that we allow all possible jail IPs as source address rather than
forcing the "primary". While IPv6 naturally has source address
selection, for legacy IP we do not go through the pain in case
IP_HDRINCL was not set. People should bind(2) for that.
This will, for example, allow ping(|6) -S to work correctly for
non-primary addresses.
Reported by: (ten 211.ru)
Tested by: (ten 211.ru)
MFC after: 4 days
addresses while walking the IPv6 address list if in the jail case
something is connecting to ::1.
Reported by: Pieter de Boer (pieter thedarkside.nl)
Tested by: Pieter de Boer (pieter thedarkside.nl)
MFC after: 4 days
by mrinfo and mtrace, was dropped by the IGMP TTL check. IGMP control
traffic must always have a TTL of 1.
Submitted by: Matthew Luckie
MFC after: 3 days
will allow people with old config options to either have it just work
(if config is new enough), or get a version error (if their config is
about 7.0 or newer) rather than getting a cryptic error about
duplicated options in the options file, or getting an error about an
unknown option, at which point they'd update their config file only to
learn they need a new config, only to learn they didn't really need to
update their config file... All this because our version checking was
in the wrong place for the past decade...
# hopefully this is the last change, and we'll be able to config with an
# 8.0 GENERIC file on stable/8 after I merge this change and add the
# compat options.
MFC after: 3 days
versions of config. Remove support for the syntax OLD = NEW form the
options file, and instead have a new file $S/conf/options-compat.
This file will be parsed as OLD NEW on each line. Bump version of
config. Since nothing in -current ever used this, there's no hazards
for current users, so I'm not bumping the version in the
Makefiles.$MACHINE. No need, really, for this version bump in
-current, but this was introduced into -stable before I realized the
version check was ineffective there, so the verison bump doesn't hurt
here and keeps the two branches in sync, versionwise, after the MFC.
MFC after: 3 days
Clearing a page table entry's accessed bit (PG_A) and setting the
page's PG_REFERENCED flag in pmap_protect() can't really be justified,
so don't do it.
we've parsed the config file. Makefile generation is too late if
we've introduce changes to the syntax of the metafiles to warn about
version skew, since we have to try to parse them and we get an parse
error that's rather baffling to the user rather than a 'your config is
too old, upgrade' which we should get.
We have to defer doing it until after we've read the user's config
file because we define machinename there. The version required to
compile the kernel is encoded in Makefile.machinename. There's no
real reason for this to be the case, but changing it now would
introduce some logistical issues that I'd rather avoid for the moment.
I intend to revisit this if we're still using config in FreeBSD 10.
This also means that we cannot introduce any config metafile changes
that result in a syntax error or other error for the user until 9.0 is
released. Otherwise, we break the upgrade path, or at least reduce
the usefulness of the error messages we generate.
# This implies that the config file option mapping will need to be redone.
MFC after: 3 days
first descriptor in TSO case. Otherwise controller can generate bad
frames during TSO. To address it, make sure to pull up ethernet +
IP + TCP header with options in first buffer. Also ensure the
buffer length of the first descriptor for TSO covers entire ethernet
+ IP + TCP with options and setup additional Tx descriptor if the
first buffer includes TCP payload.
Tested by: Amar Takhar <verm <> darkbeer dot org >
MFC after: 1 week
prevents the firmware of Fujitsu Siemens PRIMEPOWER250, which both causes
stray interrupts and erroneously enables interrupts at least when calling
SUNW,set-trap-table, in the foot.
things allows variable length messages to be easily supported.
- Extend KPI with alq_writen() and alq_getn() to support variable length
messages, which is enabled at ALQ creation time depending on the
arguments passed to alq_open(). Also add variants of alq_open() and
alq_post() that accept a flags argument. The KPI is still fully
backwards compatible and shouldn't require any change in ALQ consumers
unless they wish to utilise the new features.
- Introduce the ALQ_NOACTIVATE and ALQ_ORDERED flags to allow ALQ consumers
to have more control over IO scheduling and resource acquisition
respectively.
- Strengthen invariants checking.
- Document ALQ changes in ALQ(9) man page.
Sponsored by: FreeBSD Foundation
Reviewed by: gnn, jeff, rpaulo, rwatson
MFC after: 1 month
- replace modification of pmap resident_count with pmap_resident_count_{inc,dec}
- the pv list is protected by the pmap lock, but in several cases we are relying
on the vm page queue mutex, move pv_va read under the pmap lock
page's PG_REFERENCED flag in pmap_protect() can't really be justified.
In contrast to pmap_remove() or pmap_remove_all(), the mapping is not
being destroyed, so the notion that the page was accessed is not lost.
Moreover, clearing the page table entry's accessed bit and setting the
page's PG_REFERENCED flag can throw off the page daemon's activity
count calculation. Finally, in my tests, I found that 15% of the
atomic memory operations being performed by pmap_protect() were only
to clear PG_A, and not change protection. This could, by itself, be
fixed, but I don't see the point given the above argument.
Remove a comment from pmap_protect_pde() that is no longer meaningful
after the above change.
