if_start routines cannot currently be entered without Giant. When
the kernel is running with debug.mpsafenet != 0, this will defer
if_start execution to a task queue thread holding Giant, which may
introduce additional latency, but avoid incorrect execution.
Suggested by: dfr
in all USB ethernet drivers. The qdat structure contains a pointer
to the interface's struct ifnet and is used to process incoming
packets, so simultaneous use of two similar devices caused crashes
and confusion.
The if_udav driver appeared in the tree since Daan's PR, so I made
similar changes to that driver too.
PR: kern/59290
Submitted by: Daan Vreeken <Danovitsch@Vitsch.net>
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
because the previous interface handle gets freed when the config
number is set. This fixes a problem where memory could be accessed
after it was freed when the interface was ifconfig'd up.
Reviewed by: n_hibma
if_cuereg.h (1.5), if_kue.c (1.11), if_kuereg.h (1.5)
date: 2000/03/02 12:37:51; author: augustss;
Use ratecheck() to limit error messages on disconnect.
Break out some common functionality.
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
usb_ethersubr.c. This module maintains two queues for packets which
are each protected with one mutex. These are all the changes I can
do for now. Removing the USBD_NO_TSLEEP flag doesn't work yet: when
I tried it, the system would usually freeze up after a NIC had been
operating for a while. The usb_ethersubr module itself ought to
go away; this is the next thing I need to test.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
routines from foo_watchdog() because foo_watchdog() is called at
interrupt context, and that's a no-no due to the way the USB stack
is currently set up.
What we do now is call the TX end of frame handler manually to clear
the completed transmission, then check the send queue and send off
any frames that are pending.
Also turned off the interrupt pipe stuff in if_aue, since it appears
to tickle a bug in the USB stack that I haven't found yet.
- Sync ohci, uhci and usbdi modules with NetBSD in order to obtain the
following improvements:
o New USBD_NO_TSLEEP flag can be used in place of UQ_NO_TSLEEP
quirk. This allows drivers to specify busy waiting only for
certain transfers (namely control transfers for reading/writing
registers and stuff).
o New USBD_FORCE_SHORT_XFER flag can be used to deal with
devices like the ADMtek Pegasus that sense the end of bulk OUT
transfers in a special way (if a transfer is exactly a multiple
of 64 bytes in size, you need to send an extra empty packet
to terminate the transfer).
o usbd_open_pipe_intr() now accepts an interval argument which
can be used to change the rate at which the interrupt callback
routine is invoked. Specifying USBD_DEFAULT_INTERVAL uses the
value specified in the device's config data, but drivers can
override it if needed.
- Change if_aue to use USBD_FORCE_SHORT_XFER for packet transmissions.
- Change if_aue, if_kue and if_cue to use USBD_NO_TSLEEP for all
control transfers. We no longer force the non-tsleep hack for
bulk transfers since these are done asynchronously anyway.
- Removed quirk entry fiddling from if_aue and if_kue since we don't
need it anymore now that we have the USBD_NO_TSLEEP flag.
- Tweak ulpt, uhid, ums and ukbd drivers to use the new arg to
usbd_open_pipe_intr().
- Add a flag to the softc struct in the ethernet drivers to indicate
when a device has been detached, and use this flag to perform
tests to prevent the drivers from trying to do control transfers
if this is the case. This is necessary because calling if_detach()
with INET6 enabled will eventually result in a call to the driver's
ioctl() routine to delete the multicast groups on the interface,
which will result in attempts to perform control transfers. (It's
possible this also happens even without INET6 support enabled.) This
is pointless since we know that if the detach method has been called,
the hardware has been unplugged.
- Changed watchdog timeout routines to just call the driver init routines
to initialize the device states without trying to close and re-open the
pipes. This is partly because we don't want to frob things at interrupt
context, but also because this doesn't seem to work right and I don't
want to panic the system just because a USB device may have stopped
responding.
- Fix aue_rxeof() to be a little smarter about detecting when a double
transfer is needed. Unfortunately, the design of the chip makes it hard
to get this exactly right. Hopefully, this will go away once either
Nick or Lennart finds the bug in the uhci driver that makes this ugly
hack necessary.
- Also sync usbdevs with NetBSD.
running. It turns out that trying to read the MAC address when there's
no firmware creates a zero length transfer. This apparently doesn't
hurt anything on a UHCI controller, but OHCI controllers generate an
IOERROR, and the device doesn't initialize.
Instead, check the bcdDevice revision code. We know this will be
different when the firmware is running, so if we detect the firmware's
code instead of the bare hardware's code, we skip the firmware load.
Do not not not call m_freem() in the txeof routines. Let the netisr routine
do it. This also makes the tx netisr queuing much simpler (I can just use
another ifqueue instead of the mess I had before.)
Thanks to Bosko Milekic for making me actually think about what I was
doing for a minute.
- Add vendor/device ID for Corega USB-T ethernet adapter to necessary
places so that it will work with the kue driver.
- Add vendor/device ID for CATC Netmate devices for driver to be added
soon.
- Get really crazy about netisr stuff: avoid doing any mbuf allocations
or deallocations at splbio/splusb.
- Fix if_aue driver so that it works with LinkSys USB100TX: you need
to flip the GPIO bits just the right way to put the PHY in the right
mode.
drive the transmitter, we have to check the interface's send queue in the
TX end of frame handler (i.e. the usb bulk out callback) and push out new
transmissions if the queue has packets in it and the transmitter is
ready. But the txeof handler is also called from a USB callback running
at splusb() too.
Grrr.