doesn't have any actual interrupts is listed in a _PRT entry, only print
a warning rather than panic'ing when we walk the _PRT's to build up count
of entries that reference a given link (the counts are used as weights so
that we can attempt to balance the load across IRQs used by link devices).
Instead, only panic if we attempt to use the _PRT entry to route an
interrupt for a device.
PR: i386/89545
Tested by: anders
- MPSAFE
- Fix / reorganize attach routine. Device specific initialization must
be done after generic bus / DMA setup. At last, Virtual Channels
(vchan) works as expected.
Note: Recent commit / fix against this driver proves that major enhancements
on the generic sound layer does indeed help to expose flaw within
device specific code. There are probably other drivers that need to
be addressed as well.
Tested by: barner
MFC after: 1 week
that NetBSD implemented it independently of them (don't know which one
was actually first). This saves about 24k for those times you don't
need snapshot support (like when running off a ram disk, or in an
embedded environment where size matters).
returns EBADF. That errno is correct and is mandated by POSIX. It also
goes back to revision 1.1 of our CVS history (i.e. 4.4BSD).
The _fget() function should probably also be upated as it currently returns
EINVAL in that case rather than EBADF. (It does return EBADF for reads
on a write-only descriptor without any XXX comments oddly enough.)
Discussed with: scottl, grog, mjacob, bde
ifm_status and ifm_active. IFM_10_T gets set in the ifm_active field,
not in the ifm_status field, as far as I can tell.
Note: this was to enable a workaround that's rarely enabled. I don't know
how to corrupt my eeprom to test it, and would rather not know...
- Remove a conditional in the AMD cache detection, it's always false. [2]
- Don't try to detect a cache if only compiled for i386.
Analyzed by: Antoine Brodin <antoine.brodin@laposte.net> [1]
Submitted by: Antoine Brodin <antoine.brodin@laposte.net> [2]
that a file's atime and mtime are only set to correct fractional
second values (0-999999000ns with the current interface).
Prior to this change users could create files with values outside
that range. Moreover, on 32-bit machines tv_usec offsets larger than
4.3s would result in an unnormalized AND wrong timestamp value,
due to overflow.
MFC after: 1 week
success instead of EOPNOTSUPP when being loaded. Secondly, if there are no
ibcs2 processes running when a MOD_UNLOAD request is made, break out to
return success instead of falling through into the default case which
returns EOPNOTSUPP. With these fixes, I can now kldload and subsequently
kldunload the ibcs2 module.
PR: kern/82026 (and several duplicates)
Reported by: lots of folks
MFC after: 1 week
signal is received during the msleep, the msleep is retried
indefinitely as it just keeps returning ERESTART because of
the pending signal.
Instead, just don't PCATCH - the signal can wait.
Sponsored by: Sophos/ActiveState
requiried to keep consistent softc state before/after callback function
invocation and supposed to be sligntly faster than previous one as it
wouldn't incur callback overhead. With this change callback function
was gone.
- Decrease TI_MAXTXSEGS to 32 from 128. It seems that most mbuf chain
length is less than 32 and it would be re-packed with m_defrag(9) if
its chain length is larger than TI_MAXTXSEGS. This would protect ti(4)
against possible kernel stack overflow when txsegs[] is put on stack.
Alternatively, we can embed the txsegs[] into softc. However, that
would waste memory and make Tx/Rx speration hard when we want to
sperate Tx/Rx handlers to optimize locking.
- Fix dma map tracking used in Tx path. Previously it used the dma map
of the last mbuf chain in ti_txeof() which was incorrect as ti(4)
used dma map of the first mbuf chain when it loads a mbuf chain with
bus_dmamap_load_mbuf(9). Correct the bug by introducing queues that
keep track of active/inactive dma maps/mbuf chain.
- Use ti_txcnt to check whether driver need to set watchdog timer instead
of blidnly clearing the timer in ti_txeof().
- Remove the 3rd arg. of ti_encap(). Since ti(4) now caches the last
descriptor index(ti_tx_saved_prodidx) used in Tx there is no need to
pass it as a fuction arg.
- Change data type of producer/consumer index to int from u_int16_t in
order to remove implicit type conversions in Tx/Rx handlers.
- Check interface queue before getting a mbuf chain to reduce locking
overhead.
- Check number of available Tx descriptores to be 16 or higher in
ti_start(). This wouldn't protect Tx descriptor shortage but it would
reduce number of bus_dmamap_unload(9) calls in ti_encap() when we are
about to running out of Tx descriptors.
- Command NIC to send packets ony when the driver really has packets
enqueued. Previously it always set TI_MB_SENDPROD_IDX which would
command NIC to DMA Tx descriptors into NIC local memory regardless
of Tx descriptor changes.
Reviewed by: scottl
allocating a resource that's in the card itself.
Remove more now-redundant resource_list_add, and now-redunant code
that lives in the pci layer.
# This fixes the atheros card that I have which had its CIS in one of
# the BARs. Don't know yet if this fixes the amd64 issues reported.