linkers no longer raise an error when undefined weak symbols are
found, but relocate as if the symbol value was 0. Note that we do not
repeat the mistake of userspace dynamic linker of making the symbol
lookup prefer non-weak symbol definition over the weak one, if both
are available. In fact, kernel linker uses the first definition
found, and ignores duplicates.
Signature of the elf_lookup() and elf_obj_lookup() functions changed
to split result/error code and the symbol address returned.
Otherwise, it is impossible to return zero address as the symbol
value, to MD relocation code. This explains the mechanical changes in
elf_machdep.c sources.
The powerpc64 R_PPC_JMP_SLOT handler did not checked error from the
lookup() call, the patch leaves the code as is (untested).
Reported by: glebius
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
REPORT LUNS command is more related to target rather then specific LUN.
This node may be primary for LUNs for some reason unknown to another,
and command forwarded to another node won't be able to report them.
REQUEST SENSE is related to LUN, but in our implementation it reports
only UAs and CAs, that are stored locally rather then on primary node.
* Since new extries are now allocated explicitly, fill in
all the necessary fields for lle _before_ attaching it to the table.
* Remove ND6_LLINFO_INCOMPLETE check which was unused even in
first KAME merge (r53541).
* After that, the only new state that function can set, was
ND6_LLINFO_STALE. Given everything above, simplify logic besides
do_update and is_newentry.
* Fix nd_resolve() comment.
Previously, with serseq enabled, next command was unblocked only after
previous completed. With this change, for read operations, next command
is unblocked as soon as last media read completed. This is important
for frontends that actually wait for data move completion (like camtgt),
or when data are moved through the HA link, or especially when both.
Note that the mountlist manipulations are somewhat fragile, and not very
pretty. The reason for this is to avoid changing vfs_mountroot(), which
is (obviously) rather mission-critical, but not very well documented,
and thus hard to test properly. It might be possible to rework it to use
its own simple root mount mechanism instead of vfs_mountroot().
Reviewed by: kib@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D2698
We should not call vm_fault(), or send a signal, with interrupts
disabled. MI kernel code is not prepared for such environment, not to
mention that this increases system latency, since code appears to be
executing as being under spinlock.
The FAR register for data aborts is read before the interrupts are
enabled, to avoid its corruption due to nested exception or context
switch.
Add asserts, similar to the checks done by other architectures, about
not taking page faults in non-sleepable contexts, rather than die with
late and somewhat confusing witness diagnostic.
Reviewed by: andrew
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3669
in unknown state per spec.
Reviewed by: andrew (previous version)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3668
requirements.
Don't start the opmode and join path until a pending survey is finished.
This seems to reliably fix things.
Ideally I'd just finish off the net80211 pluggable scan stuff and implement
the methods here so if_rsu can just drive the scan machinery.
However, that's a .. later thing.
Whilst here, remove the getbuf debugging; it's okay to run out of transmit
buffers under load; it however isn't okay to not be able to send commands.
I'll fix that later.
for re-ordering.
Devices like if_rsu don't pass through action/management frames but do send
firmware commands to inform us of things. One of those notifications is
the RX A-MPDU negotiated parameters.
* Add a tunable to enable 11n if it's available, so to not anger people
who upgrade.
kenv hw.usb.rsu.enable_11n=1 before inserting the device.
* Add initial 11n htconfig bits;
* Enable 40MHz mode if it's available;
* Add 11n channels;
* Set 11n bits in the firmware.
It works for RX; I haven't tested TX aggregation just yet.
However the firmware doesn't do RX re-ordering, so I have to tie it into
the net80211 A-MPDU RX reorder path before I flip this on by default.
I've verified that I'm indeed actually seeing MCS 0->7 rates being received.
I haven't dug into whether it's actually transmitting 11n rates; I'll dig into
that later.
with a reference count of zero can't possibly be mapped, so there is never a
need for vm_page_set_invalid() to call pmap_remove_all() on them.
Reviewed by: kib
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
hold the kernel, modules, and any other loaded data. This memory block
is relocated to the kernel's expected location during the transfer of
control from the loader to the kernel.
The GENERIC kernel on amd64 has recently grown such that a kernel + zfs.ko
no longer fits in the default staging size. Bump the default size from
32MB to 48MB to provide more breathing room.
PR: 201679
Reviewed by: imp
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3666
* the tx descriptor TID is priority, not TID.
* the tx descriptor queue id mapping is separate from the
TID/priority; rather than just "BE".
TODO:
* go and re-re-re-verify the queue mappings; the linux and openbsd
mappings aren't exactly the same. I need to verify all of this
before I try to flip on 11n RX.
* Do 1T1R for now, until we read the config out of ROM and use it.
* Disable turbo mode, I dunno what this is, but the linux drivers
have this disabled.
* Set the firmware endpoints to what we read from USB.
Tested:
* RTL8712 cut 3, STA mode
data queues.
This is similar to the openbsd and rtlwifi/r92su drivers.
Note: this driver still assumes it's a 4-endpoint device; I'll enforce
that in a follow-up commit.
