struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
1. rt_check() cleanup:
rt_check() is only necessary for some address families to gain access
to the corresponding arp entry, so call it only in/near the *resolve()
routines where it is actually used -- at the moment this is
arpresolve(), nd6_storelladdr() (the call is embedded here),
and atmresolve() (the call is just before atmresolve to reduce
the number of changes).
This change will make it a lot easier to decouple the arp table
from the routing table.
There is an extra call to rt_check() in if_iso88025subr.c to
determine the routing info length. I have left it alone for
the time being.
The interface of arpresolve() and nd6_storelladdr() now changes slightly:
+ the 'rtentry' parameter (really a hint from the upper level layer)
is now passed unchanged from *_output(), so it becomes the route
to the final destination and not to the gateway.
+ the routines will return 0 if resolution is possible, non-zero
otherwise.
+ arpresolve() returns EWOULDBLOCK in case the mbuf is being held
waiting for an arp reply -- in this case the error code is masked
in the caller so the upper layer protocol will not see a failure.
2. arpcom untangling
Where possible, use 'struct ifnet' instead of 'struct arpcom' variables,
and use the IFP2AC macro to access arpcom fields.
This mostly affects the netatalk code.
=== Detailed changes: ===
net/if_arcsubr.c
rt_check() cleanup, remove a useless variable
net/if_atmsubr.c
rt_check() cleanup
net/if_ethersubr.c
rt_check() cleanup, arpcom untangling
net/if_fddisubr.c
rt_check() cleanup, arpcom untangling
net/if_iso88025subr.c
rt_check() cleanup
netatalk/aarp.c
arpcom untangling, remove a block of duplicated code
netatalk/at_extern.h
arpcom untangling
netinet/if_ether.c
rt_check() cleanup (change arpresolve)
netinet6/nd6.c
rt_check() cleanup (change nd6_storelladdr)
- use ifp instead if &ac->ac_if in a couple of nd6* calls;
this removes a useless dependency.
- use IFP2AC(ifp) instead of an extra variable to point to the struct arpcom;
this does not remove the nesting dependency between arpcom and ifnet but
makes it more evident.
there so there are no ABI changes);
+ replace 5 redefinitions of the IPF2AC macro with one in if_arp.h
Eventually (but before freezing the ABI) we need to get rid of
struct arpcom (initially with the help of some smart #defines
to avoid having to touch each and every driver, see below).
Apart from the struct ifnet, struct arpcom now only stores a copy
of the MAC address (ac_enaddr, but we already have another copy in
the struct ifnet -- if_addrhead), and a netgraph-specific field
which is _always_ accessed through the ifp, so it might well go
into the struct ifnet too (where, besides, there is already an entry
for AF_NETGRAPH data...)
Too bad ac_enaddr is widely referenced by all drivers. But
this can be fixed as follows:
#define ac_enaddr ac_if.the_original_ac_enaddr_in_struct_ifnet
(note that the right hand side would likely be a pointer rather than
the base address of an array.)
Short description of ip_fastforward:
o adds full direct process-to-completion IPv4 forwarding code
o handles ip fragmentation incl. hw support (ip_flow did not)
o sends icmp needfrag to source if DF is set (ip_flow did not)
o supports ipfw and ipfilter (ip_flow did not)
o supports divert, ipfw fwd and ipfilter nat (ip_flow did not)
o returns anything it can't handle back to normal ip_input
Enable with sysctl -w net.inet.ip.fastforwarding=1
Reviewed by: sam (mentor)
- Support IFF_MONITOR.
- Borrow some consistency for if_input() routines from if_ethersubr.c.
- Correct comments regarding fddi_input() that no longer apply.
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
o on input don't strip the Ethernet header from packets
o input packet handling is now done with if_input
o track changes to ether_ifattach/ether_ifdetach API
o track changes to bpf tapping
o call ether_ioctl for default handling of ioctl's
o use constants from net/ethernet.h where possible
Reviewed by: many
Approved by: re
transmission checks; when it is received, label the packet appropriately.
Although we don't have a local FDDI setup to test this with, the
labeling and checks are identical to other interface classes.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
- Make sure the interface is UP and RUNNING in fddi_input().
- Reorder and comment packet tests in fddi_input().
- Call if_attach() in fddi_ifattach().
- Test for a valid return from ifaddr_byindex().
- Use struct fddi_header where appropriate.
- Use bcopy() rather than memcpy().
- Use FDDI_ADDR_LEN macro instead of ETHER_ADDR_LEN macro.
- Add loadable module support.
- Use FDDI_ADDR_LEN rather than a magic number or a sizeof().
- Hide distracting sizeof() behind FDDI_HDR_LEN macro.
- Don't use sizeof(struct llc) in areas where we mean LLC_SNAPFRAMELEN.
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
