Atmel boards I have.
# All Samsung, Toshiba and SanDisk parts will need to be in this table
# since they don't conform to the ONFI specification (they are all Toggle
# parts). There's some standards for the additional bytes so there's some hope
# to decode them automatically on a per-vendor basis, but even that has
# problems (and is what motivated the ONFI parameter page).
header is split out into its own BD for processing by the firmware. When
this split occurred the data length in the BD was not being set correctly
resulting in packet corruption.
Approved by: davidcd (mentor)
by receive code waiting for data digest even when the data segment was
empty. It didn't actually read it, but it waited until those four bytes
become available in the socket buffer, i.e. until any other PDU (such as NOP)
came in.
PR: kern/185240
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Nuke dupe $FreeBSD$.
MFC after: 1 week
hw.ral.msi_disable (defaulting to using MSI).
- Probe with BUS_PROBE_DEFAULT instead of 0.
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Release resources again in case attaching fails.
- Quiesce the interrupt before detaching.
- Sprinkle const.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Trim headers.
- Nuke dupe $FreeBSD$.
MFC after: 1 week
- #if 0 the currently unused paired port linking and unlinking of dual
adapters.
- Simplify MSI/MSI-X allocation and release. For a single one, we don't need
to fiddle with the MSI/MSI-X count and pci_release_msi(9) is smart enough
to just do nothing in case of INTx.
- Canonicalize actions taken on attach failure and detach.
- Remove the remainder of incomplete support for older FreeBSD versions.
MFC after: 1 week
- Simplify MSI allocation and release. For a single one, we don't need to
fiddle with the MSI count and pci_release_msi(9) is smart enough to just
do nothing in case of INTx.
- Don't allocate MSI as RF_SHAREABLE.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Based on lessons learnt with dc(4) (see r185750), add bus space barriers to
the MII bitbang read and write functions as well as to instances of page
switching.
- Add missing locking to ed_ifmedia_{upd,sts}().
- Canonicalize some messages.
- Based on actual functionality, ED_TC5299J_MII_DIROUT should be rather named
ED_TC5299J_MII_DIRIN.
- Remove unused headers.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
fiddle with the MSI count and pci_release_msi(9) is smart enough to just
do nothing in case of INTx.
- Don't allocate MSI as RF_SHAREABLE.
MFC after: 1 week
better off living in aac_pci.c, but it doesn't seem worth creating a
aac_pci_detach() and it's also not the first PCI-specific bit in aac.c
MFC after: 3 days
This chip doesn't require the temperature sensor offset, either v1 or
v2. Doing so causes the initial calibration test to fail.
Tested:
* Intel Centrino 6150
by removing unsued file local functions and then unused callees.
A lot more warnings to resolve but someone had to break the ice.
MFC after: 10 days
X-Comment: I am not the new maintainer; chime in, it's ours.
o Forward termianl framebuffer ioctl to fbd.
o Forward terminal mmap request to fbd.
o Move inclusion of sys/conf.h to vt.h.
Sponsored by: The FreeBSD Foundation
The priority goes from "error" to "debug".
Connectors are polled every 10 seconds. Reading EDID is part of this
polling. However, when an invalid EDID is returned, this error message
is logged. When using Newcons for instance, having a kernel message
every 10 seconds is getting annoying.
Now that it's a debug message, it'll be logged only if hw.dri.debug is
enabled. This fix console spamming for some users.
Tested by: Larry Rosenman <ler@lerctr.org>
clients. Mask RX interrupts while grabbed on the atmel serial
driver. This UART interrupts every character. When interrupts are
enabled at the mountroot> prompt, this means the ISR eats the
characters. Rather than try to create a cooperative buffering system
for the low level kernel console, instead just mask out the ISR. For
NS8250 and decsendents this isn't needed, since interrupts only happen
after 14 or more characters (depending on the fifo settings). Plumb
such that these are optional so there's no change in behavior for all
the other UART clients. ddb worked on this platform because all
interrupts were disabled while it was running, so this problem wasn't
noticed. The mountroot> issue has been around for a very very long
time.
MFC after: 3 days
... for msleep/cv_*wait() return values, where wait_event*() is used
on Linux. ERESTARTSYS is the return code expected by callers when the
operation was interrupted.
For instance, this is the case of radeon_cs_ioctl() (radeon_cs.c): if
an error occurs, and the code isn't ERESTARTSYS (eg. EINTR), it logs an
error.
Note that ERESTARTSYS is defined as ERESTART, but this keeps callers'
code close to Linux.
Submitted by: avg@ (previous version)
Normal and bold fonts each have a glyph map for single or left half-
glyphs, and right half glyphs. The flag TF_CJK_RIGHT in term_char_t
requests the right half-glyph.
Reviewed by: ed@
Sponsored by: The FreeBSD Foundation
The previous code was checking the "VGA Enable" bit on the video card's
parent PCI-to-PCI bridge only. This didn't work for the case where the
video card is attached to the root PCI bus (ie. the card has no parent
PCI-to-PCI bridge).
Now, the new code:
1. checks the "VGA Enable" bit on the parent bridge only if it's a
PCI-to-PCI bridge;
2. always checks the "I/O" and "Memory address space decoding" bits
on the video card itself.
However, vendor-specific bits are not used.
This fixes the use of many integrated Radeon cards: without this patch,
we fail to detect them as the boot display and, when radeonkms looks for
the Video BIOS, it skips the shadow copy made by the System BIOS. It
then fails to fully initialize the card, because the shadow copy is the
only way to read the Video BIOS in these situations. A workaround was to
force the boot display selection using the "hw.pci.default_vgapci_unit"
tunable.
A previous version of this patch added a new function doing the checks.
Now, the vga_pci_is_boot_display() function is used to perform the
checks (only until the boot display is found) and return if the given
device is the boot display or not.
Furthermore, vga_pci_attach() logs "Boot video device" if the card being
attached it the Chosen One:
vgapci0: <VGA-compatible display> [...]
vgapci0: Boot video device
Reviewed by: kib@, jhb@ (both a previous version)
Tested by: lunatic_ (#freebsd-xorg, integrated Radeon card,
xmj (#freebsd-xorg, i915+NVIDIA cards)
