reporting. It includes:
- removing of error messages controlled by bootverbose, replacing them
with more universal and informative debugging on CAM_DEBUG_INFO level,
that is now built into the kernel by default;
- more close following to the arguments submitted by caller, such as
SF_PRINT_ALWAYS, SF_QUIET_IR and SF_NO_PRINT; consumer knows better which
errors are usual/expected at this point and which are really informative;
- adding two new flags SF_NO_RECOVERY and SF_NO_RETRY to allow caller
specify how much assistance it needs at this point; previously consumers
controlled that by not calling cam_periph_error() at all, but that made
behavior inconsistent and debugging complicated;
- tuning debug messages and taken actions order to make debugging output
more readable and cause-effect relationships visible;
- making camperiphdone() (common device recovery completion handler) to
also use cam_periph_error() in most cases, instead of own dumb code;
- removing manual sense fetching code from cam_periph_error(); I was told
by number of people that it is SIM obligation to fetch sense data, so this
code is useless and only significantly complicates recovery logic;
- making ada, da and pass driver to use cam_periph_error() with new limited
recovery options to handle error recovery and debugging in common way;
as one of results, CAM_REQUEUE_REQ and other retrying statuses are now
working fine with pass driver, that caused many problems before.
- reverting r186891 by raj@ to avoid burning few seconds in tight DELAY()
loops on device probe, while device simply loads media; I think that problem
may already be fixed in other way, and even if it is not, solution must be
different.
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
until transport will do some probe actions (at least soft reset).
Make ATA/SATA SIMs to not report bogus and confusing PROTO_ATA protocol.
Make ATA/SATA transport to fill that gap by reporting protocol to SIM with
XPT_SET_TRAN_SETTINGS and patching XPT_GET_TRAN_SETTINGS results if needed.
via `camcontrol tags ... -N ...`. There is no need to tune it in
usual cases, but some users want to have it for debugging purposes.
MFC after: 2 weeks
PMP ports such as PMP configuration or SEMB should be exposed or hidden.
These ports were always hidden before as useless and sometimes promatic.
But with updated ses driver supporting SEMB it is no longer so straight.
Keep ports hidden by default to avoid probe request ttimeouts if SEP is
not connected to PMP's SEMB via I2C, that is very often situation.
- Add low-level support for SATA Enclosure Management Bridge (SEMB)
devices -- SATA equivalents of the SCSI SES/SAF-TE devices.
- Add some utility functions for SCSI SAF-TE devices access.
Sponsored by: iXsystems, Inc.
of the default one.
Without this change setting kern.cam.ada.default_timeout to 1 instead of 30
allowed me to trigger several false positive command timeouts under heavy
ZFS load on a SiI3132 siis(4) controller with 5 HDDs on a port multiplier.
MFC after: 1 week
Even having more specific hint.ata.X.mode controls, global ones are
still could be useful from some points, including compatibility.
PR: kern/164651
MFC after: 1 week
cam_periph_runccb() since the beginning checks it and releases device queue.
After r203108 it even clears CAM_DEV_QFRZN flag after that to avoid double
release, so removed code is unreachable now.
MFC after: 1 month
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
This was previously done only for SCSI XPT in r223081, on which the change
in r223089 depended in order to respond to serial number requests. As a
result of r223089, da(4) and ada(4) devices register a d_getattr for geom to
use to obtain the information.
Reported by: ache
Reviewed by: ken
DEVFS, and make it accessible via the diskinfo utility.
Extend GEOM's generic attribute query mechanism into generic disk consumers.
sys/geom/geom_disk.c:
sys/geom/geom_disk.h:
sys/cam/scsi/scsi_da.c:
sys/cam/ata/ata_da.c:
- Allow disk providers to implement a new method which can override
the default BIO_GETATTR response, d_getattr(struct bio *). This
function returns -1 if not handled, otherwise it returns 0 or an
errno to be passed to g_io_deliver().
sys/cam/scsi/scsi_da.c:
sys/cam/ata/ata_da.c:
- Don't copy the serial number to dp->d_ident anymore, as the CAM XPT
is now responsible for returning this information via
d_getattr()->(a)dagetattr()->xpt_getatr().
sys/geom/geom_dev.c:
- Implement a new ioctl, DIOCGPHYSPATH, which returns the GEOM
attribute "GEOM::physpath", if possible. If the attribute request
returns a zero-length string, ENOENT is returned.
usr.sbin/diskinfo/diskinfo.c:
- If the DIOCGPHYSPATH ioctl is successful, report physical path
data when diskinfo is executed with the '-v' option.
Submitted by: will
Reviewed by: gibbs
Sponsored by: Spectra Logic Corporation
Add generic attribute change notification support to GEOM.
sys/sys/geom/geom.h:
Add a new attrchanged method field to both g_class
and g_geom.
sys/sys/geom/geom.h:
sys/geom/geom_event.c:
- Provide the g_attr_changed() function that providers
can use to advertise attribute changes.
- Perform delivery of attribute change notifications
from a thread context via the standard GEOM event
mechanism.
sys/geom/geom_subr.c:
Inherit the attrchanged method from class to geom (class instance).
sys/geom/geom_disk.c:
Provide disk_attr_changed() to provide g_attr_changed() access
to consumers of the disk API.
sys/cam/scsi/scsi_pass.c:
sys/cam/scsi/scsi_da.c:
sys/geom/geom_dev.c:
sys/geom/geom_disk.c:
Use attribute changed events to track updates to physical path
information.
sys/cam/scsi/scsi_da.c:
Add AC_ADVINFO_CHANGED to the registered asynchronous CAM
events for this driver. When this event occurs, and
the updated buffer type references our physical path
attribute, emit a GEOM attribute changed event via the
disk_attr_changed() API.
sys/cam/scsi/scsi_pass.c:
Add AC_ADVINFO_CHANGED to the registered asynchronous CAM
events for this driver. When this event occurs, update
the physical patch devfs alias for this pass instance.
Submitted by: gibbs
Sponsored by: Spectra Logic Corporation
(up to 2048 instead of 256 or even 64) of them with single TRIM request.
OCZ Vertex2/Vertex3 SSDs can handle no more then 64 ranges per TRIM request.
Due to lack of BIO_DELETE clustering now, it means that we could delete no
more then 2MB per request (on FS with 32K block) with limited request rate.
This change increases delete rate on Vertex2 from 250MB/s to 950MB/s.
reporting it properly (none? of known disks now).
Hitachi and WDC AF disks seem could be identified more or less formally.
For Seagate and Samsung enumerate some found models/series.
For other disks it can be forced with kern.cam.ada.X.quirks=1 tunable.
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
- make SATA SIMs announce capabilities to handle SDB with Notification bit;
- make PMP driver honor this SIMs capability;
- make SATA XPT to negotiate and enable this feature for ATAPI devices.
This feature allows supporting SATA ATAPI devices to inform system about
some events happened, that may require attention. In my case this allows
LG GH22LS50 SATA DVR-RW drive to report tray open/close events. Events
reported to CAM in form of AC_SCSI_AEN async. Further they could be used
as a hints for checking device status and reporting media change to upper
layers, for example, via spoiling mechanism of GEOM.
on per-device basis.
- While adding support for per-device sysctls, merge from graid branch
support for ADA_TEST_FAILURE kernel option, which opens few more sysctl,
allowing to simulate read and write errors for testing purposes.
existing code caused problems with some SCSI controllers.
A new sysctl kern.cam.ada.spindown_shutdown has been added that controls
whether or not to spin-down disks when shutting down.
Spinning down the disks unloads/parks the heads - this is
much better than removing power when the disk is still
spinning because otherwise an Emergency Unload occurs which may cause damage
to the actuator.
PR: kern/140752
Submitted by: olli
Reviewed by: arundel
Discussed with: mav
MFC after: 2 weeks
Add the BIO_ORDERED flag for struct bio and update bio clients to use it.
The barrier semantics of bioq_insert_tail() were broken in two ways:
o In bioq_disksort(), an added bio could be inserted at the head of
the queue, even when a barrier was present, if the sort key for
the new entry was less than that of the last queued barrier bio.
o The last_offset used to generate the sort key for newly queued bios
did not stay at the position of the barrier until either the
barrier was de-queued, or a new barrier (which updates last_offset)
was queued. When a barrier is in effect, we know that the disk
will pass through the barrier position just before the
"blocked bios" are released, so using the barrier's offset for
last_offset is the optimal choice.
sys/geom/sched/subr_disk.c:
sys/kern/subr_disk.c:
o Update last_offset in bioq_insert_tail().
o Only update last_offset in bioq_remove() if the removed bio is
at the head of the queue (typically due to a call via
bioq_takefirst()) and no barrier is active.
o In bioq_disksort(), if we have a barrier (insert_point is non-NULL),
set prev to the barrier and cur to it's next element. Now that
last_offset is kept at the barrier position, this change isn't
strictly necessary, but since we have to take a decision branch
anyway, it does avoid one, no-op, loop iteration in the while
loop that immediately follows.
o In bioq_disksort(), bypass the normal sort for bios with the
BIO_ORDERED attribute and instead insert them into the queue
with bioq_insert_tail(). bioq_insert_tail() not only gives
the desired command order during insertion, but also provides
barrier semantics so that commands disksorted in the future
cannot pass the just enqueued transaction.
sys/sys/bio.h:
Add BIO_ORDERED as bit 4 of the bio_flags field in struct bio.
sys/cam/ata/ata_da.c:
sys/cam/scsi/scsi_da.c
Use an ordered command for SCSI/ATA-NCQ commands issued in
response to bios with the BIO_ORDERED flag set.
sys/cam/scsi/scsi_da.c
Use an ordered tag when issuing a synchronize cache command.
Wrap some lines to 80 columns.
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/vdev_geom.c
sys/geom/geom_io.c
Mark bios with the BIO_FLUSH command as BIO_ORDERED.
Sponsored by: Spectra Logic Corporation
MFC after: 1 month
by timeout/error of one of probe commands, process may continue infinitely.
Make CAM ATA more robust to faulty devices and false positive detections,
abort probe after two restarts on timeouts or ten on other errors.
