* rk_cru is a cru driver that needs to be subclassed by
the real CRU driver
* rk_clk_pll handle the pll type clock on RockChip SoC, it's only read
only for now.
* rk_clk_composite handle the different composite clock types (with gate,
with mux etc ...)
* rk_clk_gate handle the RockChip gates
* rk_clk_mux handle the RockChip muxes (unused for now)
* Only clocks for supported devices are supported for now, the rest will be
added when driver support comes
* The assigned-clock* property are not handled for now so we rely a lot on the
bootloader to setup some initial values for some clocks.
Right now I'm using two Raspberry Pi's (2 and 3) to test CloudABI
support for armv6, armv7 and aarch64. It would be nice if I could
restrict this to just a single instance when testing smaller changes.
This is why I'd like to get COMPAT_CLOUDABI32 to work on arm64.
As COMPAT_CLOUDABI32 depends on COMPAT_FREEBSD32, at least for the ELF
loading, this change adds all of the bits necessary to at least build a
kernel with COMPAT_FREEBSD32. All of the machine dependent system calls
are still stubbed out, for the reason that implementations for these are
only useful if actual support for running FreeBSD binaries is added.
This is outside the scope of this work.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D13144
mapping. This uses the new common code shared with amd64.
The RTC should only be accessed via EFI. There is no locking around it as
the spec only has this as a requirement for the PC-AT CMOS device.
Reviewed by: kib, imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D12595
kernel calls this directly so the event handler is not called, meaning
the computer fails to reboot.
Tested by: cognet
MFC after: 1 week
Sponsored by: DARPA, AFRL
- Rename SOC_BCM2837 to SOC_BRCM_BCM2837, put it to opt_soc.h
- do not use files.XXX files, just move required sources to
conf/files.arm64 and make them depend on soc_brcm_bcm2837
Suggested by: andrew
RPI3 kernel config builds kernel compatible with latest upstream device
tree and firmware: https://github.com/raspberrypi/firmware/tree/master/boot
As of today it's 597c662a613df1144a6bc43e5f4505d83bd748ca
Default console is PL01x, so pi3-disable-bt dt overlay should be configured
in config.txt and stock U-Boot should be patched to use proper serial port.
Yet unsupported: SMP, VCHIQ, RNG driver. RNG requires some work due to
upstream device tree incompatibility.
Multiple people contributed to this work over time: db@, loos@, manu@
updated, and until further testing can be done, this is disabled for now.
It is expected arm64 will switch to this interface, and the old interface
will be removed before 11.0 is released.
Obtained from: ABT Systems Ltd
Relnotes: yes
Sponsored by: The FreeBSD Foundation
be used with any SoC specific drivers, for example a ThunderX nic driver
would use something like the following in files.arm64:
arm64/cavium/thunder_nic.c optional soc_cavm_thunderx thndr_nic
Reviewed by: imp
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D3479
This is only the minimum set of files needed to boot in qemu. As such it is
missing a few things.
The bus_dma code is currently only stub functions with a full implementation
from the development tree to follow.
The gic driver has been copied as the interrupt framework is different. It
is expected the two drivers will be merged by the arm intrng project,
however this will need to be imported into the tree and support for arm64
would need to be added.
This includes code developed by myself, SemiHalf, Ed Maste, and Robin
Randhawa from ARM. This has been funded by the FreeBSD Foundation, with
early development by myself in my spare time with assistance from Robin.
Differential Revision: https://reviews.freebsd.org/D2199
Reviewed by: emaste, imp
Relnotes: yes
Sponsored by: The FreeBSD Foundation
