The delay defaults to 1 sec (as it always has) unless we've done
a ~p in interactive mode or we've actually detected a HDLC frame.
This is now cleanly implemented (via async timers) so that it is
possible for LCP to come up despite the delay if an LCP REQ is
received.
This will hopefully solve situations with slow servers or slirp
scenarios (where ECHO is left on the port for a second or so before
the peer enters packet mode).
Also, ~p in interactive mode no longer changes the value of the default
openmode delay and -dedicated mode enters packet mode in the right state
according to the value of openmode.
(I completely mis-read the rfc last time 'round!)
This means:
o Better CCP/WARN Reset diagnostics.
o After we've sent a REQ and before we've received an ACK, we drop
incoming compressed data and send another REQ.
o Before sending an ACK, re-sequence all pending PRI_NORMAL data in
the modem queue so that pending packets won't get to the peer
*after* the ResetAck.
o Send ACKs with the `identifier' from the REQ frame.
o After we've received a correct ACK, duplicate ACKs are ok (and will
reset our history).
o Incorrect ACKs (not matching the last REQ) are moaned about and dropped.
Also,
o Calculate the correct FCS after compressing a packet. DEFLATE
*may* produce an mbuf with more than a single link in the chain,
but HdlcOutput didn't know how to calculate the FCS :-(
o Make `struct fsm'::reqid a u_char, not an int.
This fix will prevent us from sending id `255' 2,000,000,000 times
before wrapping to `0' for another 2,000,000,000 sends :-/
o Bump the version number a little.
The end result: DEFLATE now works over an unreliable link layer.
I can txfr a 1.5Mb kernel over a (rather bad) null-modem
cable at an average of 21679 bytes per second using rcp.
Repeat after me: Don't test compression using a loopback ppp/tcp setup as
we never lose packets and therefore never have to reset!
Validate the peers suggested IP by attempting to make a routing table
entry.
Give up IPCP negotiation if the peer NAKs us with an unusable IP.
Always SIOCDIFADDR then SIOCAIFADDR when configuring the tun device.
Using SIOCSIFDSTADDR allows duplicate dst addresses (which we don't
want)!!!
Allow up to 200 interface names (was 50) (now that ppp can play server
properly).
Up the version number (1.5 -> 1.6).
Cosmetic:
Log unexpected CCP packets in the CCP log rather than the ERROR log.
Log unexpected Config Reqs in the appropriate LCP/IPCP/CCP log rather
than the ERROR log.
Log failed route additions and deletions with WARN, not TCPIP.
Log the option id and length for unrecognised IPCP options.
Change some .Sq to .Ar in the man page.
(I *really* meant to do this *before* committing the
deflate changes in the first place - oops).
Pppd is horribly broken in this respect - refer to the
ppp man page for details. Ppp *WON'T* negotiate deflate
with pppd by default - you must ``enable'' and ``accept''
``pppd-deflate'' in your config.
While I'm in there, update the cftypes in ccp.c so that
we recognise some more protocols (we don't actually do
anything with them - just send a REJ).
Remove extraneous decls.
Add ``const'' to several places.
Allow ``make NOALIAS=1'' to remove IP aliasing.
Merge with OpenBSD - only the Makefiles vary.
We can now survive a compile with
-Wall -Wbad-function-cast -Wcast-align -Wcast-qual
-Winline -Wmissing-declarations -Wmissing-prototypes
-Wnested-externs -Wpointer-arith -Wredundant-decls
-Wshadow -Wstrict-prototypes -Wwrite-strings -Wchar-subscripts
(although the Makefile just contains -Wall).
o Add missing $Id$s
o Move extern decls from .c -> .h files
o Staticize
o Remove #includes from .h files
o style(9)ify includes
o bcopy -> memcpy
bzero -> memset
bcmp -> memcmp
index -> strchr
rindex -> strrchr
o Move timeout.h -> timer.h (making it consistent w/ timer.c)
o Add -Wmissing-prototypes
receive the ResetAck, NOT when we send the
ResetReq (as per the rfc).
o SILENTLY ignore CCPs that arrive *before*
the network phase (as per the rfc).
o Check that we've actually negotiated PRED1
before sending PRED1 output.
This bug has been around for a *VERY* long
time ! We shouldn't need to explicitly disable
PRED1 now :-)
idependently time out any of the FSMs.
Split LCP logging into LCP, IPCP and CCP logging,
and make room in "struct fsm" for the log level
that the state machine should use.
o Use syslog
o Remove references to stdout/stderr (incl perror())
o Introduce VarTerm - the interactive terminal or zero
o Allow "set timeout" to affect current session
o Change "set debug" to "set log"
o Allow "set log [+|-]flag"
o Make MSEXT and PASSWDAUTH stuff the default
o Move all #ifdef DEBUG stuff into the code - this
shouldn't be too much overhead. It's now controlled
with "set log +debug"
o Add "set log command, debug, tun, warn, error, alert"
o Remove cdefs.h, and assume an ansi compiler.
o Improve all diagnostic output
o Don't trap SIGSEGV
o SIGHUP now terminates again (log files are controlled
by syslog)
o Call CloseModem() when changing devices
o Fix parsing of third arg of "delete"
I think this fixes the "magic is same" problems that some
people have been experiencing.
The man page is being rewritten. It'll follow soon.
alias commands simply won't work. Only root may specify the
location of the alias lib (otherwise, it's hard-coded).
Make logprintf silently fail if LogOpen hasn't been called.
Suggested by: eivind
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
to be used to expand things beyond the size of the buffer passed in. Also
do a general cleanup of sprintf -> snprintf as well as strcpy and strncat
safety. Also expand some buffers to allow for the largest possible data
that might be used.
This is a 2.2 candidate. However, it needs to be vetted on -current
since little testing has been done on this due to my lack of PPP on
this machine.
Reviewed by: Jordan Hubbard, Peter Wemm, Guido van Rooij
add some logging functionality which I find very useful.
'set debug link' will record just link up/down and address assignments.
'set debug connect' will record the entire chat dialog
'set debug carrier' will record just chat lines including 'CARRIER'
(so that I can be sure I'm getting a 28.8 line).
There was a global change required to permit LogPrintf to take a bit
mask instead of a bit position value (to permit logging some events
on either of two flags, so that no change in 'set debug lcp' would
result from the code supporting 'link'. Thus the diffs are rather
long for such a small change. The man page is also touched.
Oh, and there was a slight syntax problem in route.c
Reviewed by: phk
Submitted by: Tony Kimball <alk@Think.COM>
o Supporting SYNC SIO device (But need a device driver)
- add "set speed sync"
o Fixing bug for Predictor-1 function.
o Add new parameter that re-sent interval for set timeout commands.
o Improving RTT (Round Trip Time) and reducing processor time.
- Previous Timer service was using polling, and now using
SIGALRM ;-)
- A 0.94beta2 will not work correctly....
-- Follows are additinal feature not including 0.94beta2
o Support Proxy ARP
- add "enable/disable proxy" commands
o Marging common routine in CHAP/PAP.
o Enhancing LCP/IPCP log information.
o Support local Authfication connection on port 300x and tty.
- You can set up pair of your "hostname -s" and
password in ppp.secret. if either ppp.secret file nor
your hostname line don't exist, It will notify a message
and working as same as previous version.(Backword compatibility)
- If you did set up them, It's allow connection but nothing to do
except help and passwd command.
- add "passwd yourpasswd" commands
o Support afilter - keep Alive filter that a packet can send/receiving
according to ifilter/ofilter but doesn't count it as preventing idle
timer expires.
- Same syntax of other filters.
o Fixing bugs reported by current user for previous one. Thanks !!
Reviewed by: Atsushi Murai (amurai@spec.co.jp)
