if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
Use EP_{READ,WRITE}{,_MULTI}_{1,2,4} instead. I've had several people
submit patches like this over the years of varying qualities, markm
being the last. The names were chosen in consulation with mdodd on
irc.
I've tested this with only PCMCIA cards: 3CCE589EC and 3CCSH572BT.
I've not tried with my more extensive ISA, EISA and cbus collection.
Reviewed by: mdodd
flag'ed INTR_MPSAFE. In ep_if_start(), use the IF_DEQUEUE macro to
grab the next mbuf to send, and use IF_PREPEND if the card is busy
and we actually can't handle it right now.
The old code was first getting the mbuf by taking it from the queue
without using the macros, thus without locking, and without removing
it from the queue either. It was later assuming that IF_DEQUEUE would
give him this same mbuf.
Tested by: mich
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
1) We shouldn't continue when we get a RX complete because we ack it
and the TX complete.
2) Fix a couple of spl leaks
(why splbio is needed in ISR, I cannot understand).
MFC after: 3 days
ep driver. The rest of the patch will wait until I can put the time
into it to get it righter than the kludge it is.
This protects us against card eject problems at all times,e xecpt when
we're in the epintr ISR.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
ifconfig and bogus ethernet address (4b:57:4b:57:4b:57) has been
hacked around. I'll revisit this when I have a clue whats going on.
Reviewed by: obrien
Use IFQ_MAXLEN instead. This seemed like a good idea at the time since
most 3c509s have all of 2k for their TX fifo. My intention was to revisit
ifq_maxlen and auto-scale it or something.
ttcp-t: 16777216 bytes in 21.53 real seconds = 761.07 KB/sec +++
ttcp-t: 2771 I/O calls, msec/call = 7.96, calls/sec = 128.72
ttcp-t: 0.0user 2.9sys 0:21real 13% 20i+280d 222maxrss 0+2pf 717+0csw
ttcp-r: 16777216 bytes in 14.11 real seconds = 1161.48 KB/sec +++
ttcp-r: 2050 I/O calls, msec/call = 7.05, calls/sec = 145.33
ttcp-r: 0.0user 1.4sys 0:14real 10% 87i+1198d 196maxrss 0+1pf 1949+186csw
I've got some tweaks that move the TX speed up to the RX speed but I've
got to groom them from the mess I've made of my source tree.
Yelled at by: wpaul
- Rip out all the static softc stuff and do softc allocation the right way.
- Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY
method to enumerate all non-PnP ISA devices.
This has the following consequences:
- No 'ep' devices may be hardwired.
- All hardwired devices will probably be detected twice.
By hardwired I mean:
device ep0 at isa? port 0x300 irq 10
- 'ep' devices are ordered by bus, slot, and then MAC address.
- Make 3c509B cards work in PnP mode. Yes, they really work.
- Convert over to using ifmedia for media selection. No more of this
lame 'linkX' stuff.
- Consolidate a lot of duplicated code.
- Make a stab at not breaking MII based PCCARD devices.
I doubt that the PCCARD stuff works any more than it did before my
changes but theres hope. My PCCARD hardware should arrive in a
week or so.
- Retreive the media settings from the card EEPROM rather than guessing.
I've got a 3c509-TPO that thinks its got an AUI port and if others
can report similar problems I'll write a bit of clever code that will
fix this but right now it works correctly on all but 1 card.
- Clean up a few things and make some cosmetic changes.
- Add myself as the MAINTAINER since nobody else wants to. I'm
in the best position to do this as I've got an example of most
of the cards:
EISA 3c579 bnc/aui
MCA 3c529 tp/aui
ISA 3c509 tpo
ISA-PnP 3c509B combo
If someone wants to send me a any cards I don't have I'd appriciate
it. Also welcome are 3c59x boards since I'll be folding if_vx and
if_ep at some point.
I'm committing this from a laptop running this driver. Have only one
devclass for all ep devices (at least for pccard and eisa) so unit
numbering is sane. Might not work with both isa and non-isa devices
on the same system until ep is updated (Matt has some patches in the
pipeline which should resolve this, he wanted me to commit this so he
can resolve any conflicts against cvs rather than my patches).
Reviewed by: Matt Dodd <mdodd@freebsd.org>
- Split out the prototypes, externs and struct decls from if_epreg.h into
if_epvar.h.
- Add support for MCA based Etherlink III (3c529) devices.
None of this code is used right now; the old if_ep driver is still
in place and used.
I will eventually get around to converting if_ep_isa.c to newbus once I've
had a talk with Peter and DFR about the DEVICE_IDENTIFY() method.
I have tested this code on my PS/2. It works. I would like EISA and ISA
testers since my example hardware hasn't arrived yet.
Add:
dev/ep/if_ep.c optional ep
dev/ep/if_ep_isa.c optional ep isa
dev/ep/if_ep_eisa.c optional ep eisa
dev/ep/if_ep_mca.c optional ep mca
dev/ep/if_ep_pccard.c optional ep card
to sys/conf/files
Remove:
i386/eisa/3c5x9.c optional ep
i386/isa/if_ep.c optional ep
from sys/i386/conf/files.i386
PCCARD testers wanted!
I will switch off and cvs rm the old driver in favor of this copy once
I've had positive feedback or have the hardware to verify that it works.
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
for you to be told there was an error [during verbose boot].
I poked him for the fix, he poked me to get it committed.
Submitted by: Jason Young <doogie@anet-stl.com>
