controller driver by piggybacking the SOF interrupt when issuing new
and checking old transfers. Number of interrupts was reduced by 30%
when doing Isochronous transfers.
Use correct GINTMSK_XXX macros when accessing the DWC OTG interrupt
mask register.
Add code to adjust the frame interval register which influences the
SOF rate.
MFC after: 2 weeks
speed data traffic going directly to a USB device or through a
so-called USB transaction translator.
Add checks that we are not overusing the TX FIFO.
MFC after: 2 weeks
define a few imx_ccm_foo() functions that are implemented by the imx51 or
imx6 ccm code. Of course, the imx6 ccm code is still more a wish than
reality, so for now its implementations just return hard-coded numbers.
a jtag debugging product, which was used on early Beaglebone boards (later
boards used a standard FTDI 2232C product ID). Change the name accordingly,
and also add an entry for XDS100V3, the latest version of that product
which has its own new product ID number.
Device type and revision is now determined from the bcdDevice field and
doesn't need to be in the table at all. The feature that skips creation
of /dev/ttyU* entries for jtag and gpio interfaces is enhanced:
- The feature is now optional, but enabled by default. A tunable and
sysctl are available to control it: hw.usb.uftdi.skip_jtag_interfaces.
- We no longer assume interface #0 is the only jtag interface. Up to
eight interfaces per chip can be flagged as jtag. (Current ftdi chips
support a max of 4 interfaces; this leaves room for growth.)
- Some manufacturers don't change the product ID or use the same ID for
different devices intended for both serial-comms and jtag/gpio use.
Often while the product ID is the same, the product name string is
different, so it's now possible to search for the product name in a
table of strings and get the set of non-tty interfaces from that table.
- Add a comment about FTDI and ZLPs.
- Correctly check odditiy of baud rate divisor.
- Correct IOCTL handling for "error" and "event" char.
MFC after: 1 weeks
other modes supported by the FTDI serial adapter chips.
In addition to adding the new ioctls, this change removes all the code
that reset the chip at attach and open/close time, and also the code
that turned on RTS/CTS flow control on open without any permission to do
so (that was just always a bug in the driver).
When FTDI chips are configured as GPIO or MPSSE or other special-purpose
uses by an attached serial eeprom, the chip will power on with certain
pins driven or floating, and it's important that the driver not do
anything to the chip to perturb that unless it receives a specific
command to do so. When used for "plain old serial comms" the chip
powers on into the right mode and never needs to be reset while it's
running to operate properly, so this change is transparent to most users.
While I'm here, remove aue_eeprom_getword() as its only usage is to
read station address and make it more readable. This change is
inspired by NetBSD.
With this change, aue(4) should work on big endian architectures.
PR: 188177
default wMaxPacketSize (64 or 512 bytes). This actually helps older FTDI
devices (which were USB 1/full speed) more than the new H-series high
speed, but even for the new chips it helps cut the number of interrupts
when doing very high speed (3-12mbaud).
Recent FDTI chips have the ability to operate at up to 12mbps. The newer
chips with faster clocks have the same usb vendor/product IDs as the older
chips; the bcdDevice field must be used to detect the newer versions. This
change includes a new function to do that instead of using just the IDs from
the vendor/product table.
The code to choose the baud clock divisor is completely rewritten. In
addition to supporting the new higher clock rates, the rewrite fixes a
longstanding bug in the old code which put the high bits of the fractional
part of the divisor into the wrong place in the wIndex field. That bug
was mostly harmless -- it accidentally didn't affect standard baud rates
and would only show up when using relatively fast non-standard rates.
create character devices. The deadlock can happen if an application is
issuing IOCTLs which require USB refcounting, at the same time the USB
device is detaching.
There is already a counter in place in the USB device structure to
detect this situation, but it was not always checked ahead of invoking
functions that might destroy character devices, like detach, set
configuration, set alternate interface or detach active kernel driver.
Reported by: Daniel O'Connor <doconnor@gsoft.com.au>
MFC after: 1 week
The NetBSD Foundation states "Third parties are encouraged to change the
license on any files which have a 4-clause license contributed to the
NetBSD Foundation to a 2-clause license."
This change removes clauses 3 and 4 from copyright / license blocks that
list The NetBSD Foundation as the only copyright holder.
Sponsored by: The FreeBSD Foundation
1) Add support for page back/forward.
2) While doing HOR scrolling, disable VER scrolling.
3) Checking dx_sum and dy_sum before emulate right button, this can
avoids unexpected right button press.
4) Fix stable pointer operation when emulating middle button.
Submitted by: Huang Wen Hui <huanghwh@gmail.com>
MFC after: 2 weeks
- Support for double-tap and drag.
- Support for 2-finger horizontal scrolling which translates to page-back/forward events.
- Single finger tap is equivalent to a left-button press.
- Two-finger taps are mapped to the right-button click.
- Three fingers are mapped to middle button.
- Add sysctl to disable single finger tapping.
- Fix for multiple open of /dev/atp0
- Enhanced support for the Fountain/Geyser family by adding Geyser4.
- Update manual page.
Submitted by: Rohit Grover <rgrover1@gmail.com>
MFC after: 2 weeks
Before this patch, curvnet was NULL.
When the VIMAGE kernel option is enabled, this eliminates
kernel panics when USB ethernet devices are plugged in.
PR: 183835
Submitted by: Hiroo Oono <hiroo.ono at gmail dot com>
about uss820dci_odevd being unused, by adding it to the part that
handles getting descriptors.
Reported by: loos
Reviewed by: hselasky
MFC after: 3 days
