- Ensure `section` doesn't overrun section by using strlcpy instead of
strcpy [*].
- Use strdup instead of malloc + strcpy (this wasn't flagged by Coverity,
but is an opportunistic change).
MFC after: 1 week
Reported by: Coverity
CID: 1006826 [*]
avoid returning an uninitialized value
There are some really complicated, snakey if-statements combined with
switch statements that could result in an invalid value being returned
as `ret`
MFC after: 1 week
Reported by: Coverity
CID: 1006551
as the listening address in snmpd_input(..)
Stash the IPv4 address of the receiver via the recv(..) callback and use it in
the send(..) callback for the transport by specifying IP_SENDSRCADDR for the
control message type.
Add sendmsg logic to the UDP transport's send(..) callback and use the
respective send(..) callback for the transport instead of calling sendto in
snmpd_input(..).
MFC after: 3 weeks
Obtained from: Isilon OneFS (^/onefs/branches/BR_8_0_0_DEV@r507595)
Submitted by: Thor Steingrimsson <thor.steingrimsson@isilon.com>
Sponsored by: Dell EMC Isilon
Again, for reasons I don't yet understand, this is not being flagged by the
compiler. Unlike the issue addressed in r310587, this problem existed prior
to r310586
MFC after: 2 weeks
X-MFC with: r310586, r310587
Add recv callback to transport layer to better facilitate code reuse and
readability and for symmetry with send callback. Move recv_dgram and
recv_stream to udp_recv and lsock_recv, respectively, and make the
beforementioned functions recv callbacks for the udp and lsock transports,
respectively.
Consolidate the check_priv* functions in their relevant trans*.c source to
limit scope/use.
Note: this code is roughly based content from the submitter, although this
was modified to be more of a direct move from snmpd/main.c to the trans_*.c
sources, and to reduce unnecessary static function declarations.
MFC after: 2 weeks
Submitted by: Thor Steingrimsson <thor.steingrimsson@isilon.com>
Sponsored by: Dell EMC Isilon
- Explicitly test snmp_pdu_encode against SNMP_CODE_OK instead of assuming
any non-zero value is bad.
- Print out the code before calling abort() to give the end-user something
actionable to debug without having to recompile the binary, since the
core might not have these details.
MFC after: 1 week
The CMSG_ family of macros take care of alignment, so we don't need r299830
at all, even if it was correct. Put NO_WCAST_ALIGN into Makefile.
Together with: peter
Use memcpy instead of using direct assignment of void* pointers with
CMSG_DATA(..), which changes alignment
MFC after: 3 weeks
Reported by: clang
Sponsored by: EMC / Isilon Storage Division
SNMPD_INPUT_FAILED is `enum snmpd_input_err` type (which matches the return
code from the function). SNMP_CODE_FAILED is `enum snmp_code` type.
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
- Set IP_RECVDSTADDR sockopt on the socket only in case if
it is INADDR_ANY bound.
- Supply IP_SENDSRCADDR control message only if we did receive
IP_RECVDSTADDR control message.
This fixes operation of snmpd bound to a specific local IP address.
PR: bin/171279
IP_SENDSRCADDR control with datagram message we reply with. This makes
bsnmpd reply from exactly same address that request was sent to, thus
successfully bypassing stateful firewalls or other kinds of strict checking.
PR: bin/171279
from the control message, actually never worked. This means check_priv()
didn't work for local dgram sockets.
The SCM_CREDS control messages is received only in two cases:
1) If we did setsockopt(LOCAL_CREDS) on our socket, and in this case
the message is struct sockcred.
2) If sender did supplied SCM_CREDS control message in his sendmsg()
syscall. In this case the message is struct cmsgcred.
We can't rely on 2), so we will use 1) for dgram sockets. For stream
sockets it is more reliable to obtain accept-time credentials, since
SCM_CREDS control message is attached only on first read. Thus:
o Do setsockopt(LOCAL_CREDS) on local dgram sockets.
o Split check_priv() into check_priv_stream() and check_priv_dgram(),
and call them from recv_stream() and recv_dgram() respectively.
o Don't provide space for SCM_CREDS control message in recv_stream().
o Provide space for SCM_CREDS control message in recv_dgram(), but there
is no need to initialize anything in it.
o In recv_dgram() do not blindly expect that first message is SCM_CREDS,
instead use correct search cycle through control messages.
basically disables any access unless other strings are set in the config
file. Note, that there is no way to set the communities back to NULL once
they're set to something not NULL.
