by timeout/error of one of probe commands, process may continue infinitely.
Make CAM ATA more robust to faulty devices and false positive detections,
abort probe after two restarts on timeouts or ten on other errors.
This makes things easier for target implementations to calculate how many
elements they need to allocate.
Discussed with: mjacob, gibbs
MFC after: 1 week
the case of immediate unconfigure after configure. Hold the periph an
extra count while we have the task to create sysctl context outstanding
so that the periph doesn't go away unexpectedly.
Sponsored by: Panasas
Reviewed by: scsi@
MFC after: 1 month
better devices. This can be disabled on a per-device basis using quirks as
well.
This also handles the case where there is actually no connected LUN 0
(which can definitely be the case for storage arrays).
Reviewed by: scsi@
MFC after: 1 month
for REPORT and SET TARGET PORT GROUP commands (foundations for future work).
Regularize opcodes to be upper case hex.
Pick *one* of tab or space after #define (tab) and stick with that.
MFC after: 2 weeks
whole bus (XPT_SCAN_BUS) and a single lun on that bus (XPT_SCAN_LUN).
It's less resource comsumptive than scanning a whole bus when the
caller knows only one target has changes.
Reviewed by: scsi@
Sponsored by: Panasas
MFC after: 1 month
hook it up to ada(4) also. While at it, rename *ad_firmware_geom_adjust()
to *ata_disk_firmware_geom_adjust() etc now that these are no longer
limited to ad(4).
Reviewed by: mav
MFC after: 3 days
- device initiated power management (some devices support only this way);
- Automatic Partial to Slumber Transition (more power saving);
- DMA auto-activation (expected to slightly improve performance).
More features could be added later, when hardware supports.
As scottl@ noticed, max_target/max_lun was intended to be only a hint for
existing bus scanner. Some FC/SAS SIMs report fake values there, that are
smaller then maximum supported IDs. In that case this check makes impossible
manual scan outside hinted range.
For ATA/SATA SIMs respective check was instead implemented at SIM level.
Newer SCSI SIMs expected to have these checks at driver or firmware level.
Some older SCSI SIMs have no this check and the issues will get back there.
d_mediasize
CD_FLAG_VALID_TOC is not required for setting those media properties.
PR: kern/145385
Submitted by: Juergen Lock <nox@jelal.kn-bremen.de>
a slightly different version
Tested by: Pavel Sukhoy <sukhoy@ripn.net>,
Markus Wild <m.wild@cybernet.ch>,
Juergen Lock <nox@jelal.kn-bremen.de>,
uqs
MFC after: 1 week
xpt_done for queued requests. This solves the problem of
indefinite hangs for unspecified transports when XPT_SCAN_BUS
is called.
A few minor cosmetics elsewhere.
MFC after: 1 week
Add Power Up In Stand-by feature support. Device with PUIS enabled
require explicit command to do initial spin-up. Mark that command
with CAM_HIGH_POWER flag, to allow CAM manage staggered spin-up.
Make CAM to stop all attached devices on system shutdown.
It allows devices to park heads, reducing stress on power loss.
Add `kern.cam.power_down` tunable and sysctl to controll it.
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
- For SSDs use TRIM feature of DATA SET MANAGEMENT command, as defined by
ACS-2 specification working draft.
- For CompactFlash use CFA ERASE command, same as ad(4) does.
With this patch, `newfs -E /dev/ada1` was able to restore write speed of
my heavily weared OCZ Vertex SSD (firmware 1.4) up to the initial level
for the most part of it's capacity. Previous 1.3 firmware, even reportiong
TRIM capabilty bit set, was not working, reporting ABORT error for every
DSM command.
I have no idea whether it is normal, but for some reason it takes 200ms
to handle any TRIM command on this drive, that was making delete extremely
slow. But TRIM command is able to accept long list of LBAs and the length of
that list seems doesn't affect it's execution time. Implemented request
clusting algorithm allowed me to rise delete rate up to reasonable numbers,
when many parallel DELETE requests running.
