isolated but also powered down after a reset and while they just work fine
[sic] when both is the case they don't if they are only deisolate but still
powered down. So in order to put PHYs in an overall normal operation mode
for the common case, ensure in mii_phy_reset() that they are not powered
down after a reset. Unfortunately, this only helps in case of BCM5421,
while BCM5709S apparently only work when they remain isolated and powered
down after a reset. So don't call mii_phy_reset() in brgphy_reset() and
implement the reset locally leaving the problematic bits alone. Effectively
this bypasses r221812 for brgphy(4).
Thanks to Justin Hibbits for doing a binary search in order to identify
the problematic commit.
PR: 157405, 158156
Reviewed by: yongari (mii_phy_reset() part)
Approved by: re (kib)
MFC after: 3 days
cores with temp in the range 101-105 have been found in the past.
Sponsored by: Sandvine Incorporated
Reviewed by: delphij, emaste
Approved by: re (kib)
MFC after: 3 days
avoid lost timer interrupts. Previous optimization attempt doing it only
for intervals less then 5000 ticks (~300us) reported to be unreliable by
some people. Probably because of some heavy SMI code on their boards.
Introduce additional safety interval of 128 counter ticks (~9us) between
programmed comparator and counter values to cover different cases of
delayed write found on some chipsets.
Approved by: re (kib)
to implement fchown(2) and fchmod(2) support for several file types
that previously lacked it. Add MAC entries for chown/chmod done on
posix shared memory and (old) in-kernel posix semaphores.
Based on the submission by: glebius
Reviewed by: rwatson
Approved by: re (bz)
mutex, which would lead to a deadlock.
Many thanks to Areca for their continued support of FreeBSD.
Submitted by: Ching Huang <ching2048 areca com tw>
Tested by: Willem Jan Withagen <wjw digiware nl>
MFC after: 3 days
Approved by: re (kib)
We also revive loop down freezes. We also externaliz within isp
isp_prt_endcmd so something outside the core module can print
something about a command completing. Also some work in progress to
assist in handling timed out commands better.
Partially Sponsored by: Panasas
Approved by: re (kib)
MFC after: 1 month
once. Use taskqueues to do the actual work.
Fix an offset line.
Fix isp_prt so that prints from just one buffer, which makes it
appear cleanly cleanly in logs on SMP systems.
Approved by: re (kib)
MFC after: 1 month
kernel for FreeBSD 9.0:
Add a new capability mask argument to fget(9) and friends, allowing system
call code to declare what capabilities are required when an integer file
descriptor is converted into an in-kernel struct file *. With options
CAPABILITIES compiled into the kernel, this enforces capability
protection; without, this change is effectively a no-op.
Some cases require special handling, such as mmap(2), which must preserve
information about the maximum rights at the time of mapping in the memory
map so that they can later be enforced in mprotect(2) -- this is done by
narrowing the rights in the existing max_protection field used for similar
purposes with file permissions.
In namei(9), we assert that the code is not reached from within capability
mode, as we're not yet ready to enforce namespace capabilities there.
This will follow in a later commit.
Update two capability names: CAP_EVENT and CAP_KEVENT become
CAP_POST_KEVENT and CAP_POLL_KEVENT to more accurately indicate what they
represent.
Approved by: re (bz)
Submitted by: jonathan
Sponsored by: Google Inc
device having the same name like a previous one is not created before the old
one is gone. This fixes some panics due to asserts in the devfs code which
were added recently.
Approved by: re (kib)
MFC after: 1 week
- Ignore some more internal SAS device status change events.
- Correct inverted Bus and TargetID arguments in a warning.
o Add a warning for MPI_EVENT_SAS_DISCOVERY_ERROR events, which can help
identifying broken disks.
Submitted by: Andrew Boyer
Approved by: re (kib)
Committed from: Chaos Communication Camp 2011
ID. This fixes USB_SET_IMMED call (synchronous operation) of the uhid(4)
driver on devices with single report ID.
Reviewed by: hselasky
Approved by: re (kib)
MFC after: 1 week
needing this particular modification.
It can be called during ath_dfs_radar_enable() and still achieve the
same functionality, so I am.
Approved by: re (kib, blanket)
Remove this debugging, it's not needed anymore and when not enabled,
those variables trigger a compiler warning.
Approved by: re (kib, blanket)
Pointy-hat-to: adrian, for not testing a non-debug compile of this code enough
allows it to be overridden at runtime.
Thus, add a function which updates ah_dfsDomain after a channel set
call to ath_hal_set_channels().
Approved by: re (kib, blanket)
and the Atheros reference code.
The radar detection code needs to know what the current DFS domain is.
Since net80211 doesn't currently know this information, it's extracted
from the HAL regulatory domain information.
The specifics:
* add a new ath_dfs API hook, ath_dfs_init_radar_filters(), which
updates the radar filters whenever the regulatory domain changes.
* add HAL_DFS_DOMAIN which describes the currently configured DFS domain .
* add a new HAL internal variable which tracks the currently configured
HAL DFS domain.
* add a new HAL capability, HAL_CAP_DFS_DMN, which returns the currently
configured HAL DFS domain setting.
* update the HAL DFS domain setting whenever the channel setting is
updated.
Since this isn't currently used by any radar code, these should all
be no-ops for existing users.
Obtained from: Atheros
Submitted by: KBC Networks, sibridge
Approved by: re (kib, blanket)
if 5ghz fast clock is enabled in the current operating mode.
It's slightly dirty, but it's part of the reference HAL and used by
the (currently closed-source) radar event code to map radar pulses
back to microsecond durations.
Obtained from: Atheros
Approved by: re (kib, blanket)
the ar9130 code.
Since at least one kernel config specifies individual ath HAL chips
rather than just "device ath_hal" (arm/AVILA), I'm doing this so people
aren't caught out when they update to -HEAD or 9.0 and discover their
ath setup doesn't compile.
I'll revisit this with a proper fix sometime before 9.0-RELEASE.
Approved by: re (kib, blanket)
Pointed out by: ray@
Pointy hat to: adrian@
systems, in the same way that AR9130 embedded systems work.
This isn't -everything- that is required - the PCI glue still
needs to be taught about the eepromdata hint, along the same
lines as the AHB glue.
Approved by: re (kib, blanket)
Mac with this chipset does not initialize AHCI mode unless it is started
from EFI loader. However, legacy ATA mode works.
Submitted by: jkim@ (original version)
Approved by: re (kib)
MFC after: 1 week
truly.
Before 802.11n, the RX descriptor list would employ the "self-linked tail
descriptor" trick which linked the last descriptor back to itself.
This way, the RX engine would never hit the "end" of the list and stop
processing RX (and assert RXEOL) as it never hit a descriptor whose next
pointer was 0. It would just keep overwriting the last descriptor until
the software freed up some more RX descriptors and chained them onto the
end.
For 802.11n, this needs to stop as a self-linked RX descriptor tickles the
block-ack logic into ACK'ing whatever frames are received into that
self-linked descriptor - so in very busy periods, you could end up with
A-MPDU traffic that is ACKed but never received by the 802.11 stack.
This would cause some confusion as the ADDBA windows would suddenly
be out of sync.
So when that occured here, the last descriptor would be hit and the PCU
logic would stop. It would only start again when the RX descriptor list
was updated and the PCU RX engine was re-tickled. That wasn't being done,
so RXEOL would be continuously asserted and no RX would continue.
This patch introduces a new flag - sc->sc_kickpcu - which when set,
signals the RX task to kick the PCU after its processed whatever packets
it can. This way completed packets aren't discarded.
In case some other task gets called which resets the hardware, don't
update sc->sc_imask - instead, just update the hardware interrupt mask
directly and let either ath_rx_proc() or ath_reset() restore the imask
to its former setting.
Note: this bug was only triggered when doing a whole lot of frame snooping
with serial console IO in the RX task. This would defer interrupt processing
enough to cause an RX descriptor overflow. It doesn't happen in normal
conditions.
Approved by: re (kib, blanket)
interrupt storm.
This is easily triggered by flipping on and off tcpdump -y IEEE802_11_RADIO
w/ witness enabled. This causes a whole lot of console IO and when you're
attached to a serial console (eg on my AR7161 embedded board), the RX
interrupt doesn't get called quickly enough and the RX queue fills up.
This wasn't a problem in the past because of the self-linked RX descriptor
trick - the RX would never hit the "end" of the RX descriptor list.
However this isn't possible for 802.11n (see previous commit history for
why.)
Both Linux ath9k and the Atheros reference driver code do this; I'm just
looking now for where they then restart the PCU receive. Right now the RX
will just stop until the interface is reset.
Obtained from: Linux, Atheros
Approved by: re (kib)
The AR9280 apparently has an issue with descriptors which straddle a page
boundary (4k). I'm not yet sure whether I should use PAGE_SIZE in the
calculations or whether I should use 4096; the reference code uses 4096.
This patch fiddles with descriptor allocation so a descriptor entry
doesn't straddle a 4kb address boundary. The descriptor memory allocation
is made larger to contain extra descriptors and then the descriptor
address is advanced to the next 4kb boundary where needed.
I've tested this both on Merlin (AR9280) and non-Merlin (in this case,
AR9160.)
Obtained from: Linux, Atheros
Approved by: re (kib)
This seems to indicate whether to program the NIC for fractional 5ghz
mode (ie, 5mhz spaced channels, rather than 10 or 20mhz spacing) or not.
The default (0) seems to mean "only program fractional mode if needed".
A different value (eg 1) seems to always enable fractional 5ghz mode
regardless of the frequency.
Obtained from: Atheros
Approved by: re (kib)
Calibration/PCI data that's written to flash (rather than EEPROM attached
to the NIC) is typically already in host-endian. The existing checks
end up swapping 16 bit words incorrectly - the correct solution would be
to read the magic value and determine the EEPROM endianness from that.
(This is what Linux does.)
This doesn't completely enable embedded use of the AR9285/AR9287 -
notably, the EEPROM read methods need to be made generic and available
to all EEPROM drivers. I'll worry about that later.
Approved by: re (kib)
* I messed up the order of parameter true/false; oops!
* AR_PHY_RADAR_1 was being written at the wrong place, and was writing
potential garbage to the hardware.
Approved by: re (kib)
* Teach the AR5212/AR5416 ANI code to use the RX filter methods, rather
than calling the RX filter routines directly.
* Make HAL_ANI_PRESENT and HAL_ANI_MODE unconditionally available,
regardless of whether ah_ani_function is masking it.
* (Mostly) fully disable ANI if interference mitigation is disabled.
When disabled, the ANI code doesn't touch any ANI/PHY registers,
leaving them the default value. This is in line with what the
Atheros reference driver does.
* Correctly set the ANI parameters during ANI reset, rather than
when ANI is enabled. In this way, if ANI is disabled or enabled
whilst the NIC is not active (and there's no current channel),
bogus parameters or a NULL pointer deference doesn't occur.
There's still some lingering issues - notably, the MIB events/interrupts
aren't fully disabled, so MIB interrupts still occur. I'll worry about
that later.
Approved by: re (kib)
