fact, use the same values here that we use on 32-bit x86 and MIPS. Some
machines were reported to have problems with the more aggressive values.
Reported and tested by: andrew
thread scheduled by interrupt fired after we entered critical section.
None of cpu_sleep() implementations on ARM check sched_runnable() now, so
put the first line of defence here. This mostly fixes unexpectedly long
sleeps in synthetic tests of calloutng code and probably other situations.
seems to cause more problems then previous behavior: it either breaks
initilization sequence in other places or uncovers problems with
high-speed mode timing for SDHCI 3.0
Fix pull-up and pull-down values of gpio.
According to A10 user manual possible pull register
values are 00 Pull-up/down disable, 01 Pull-up, 10 Pull-down.
Approved by: gonzo@
submap. Otherwise, after r246204, the auto-scaling logic in kern_malloc.c
tries to create a kmem submap that consumes the entire kernel map on a
Pandaboard with 1 GB of RAM.
Tested by: gonzo
machine to another. Therefore, VM_MAX_KERNEL_ADDRESS can't be a constant.
Instead, #define it to be a variable, vm_max_kernel_address, just like we
do on sparc64.
Reviewed by: kib
Tested by: ian
SDHCI driver
Suggested by: Daisuke Aoyama
- Set initilization sequence frequency to 8MHz. It should fix Data CRC
errors. Standard requires initialization sequence to be executed
at 400KHz but on this hardware low frequncies seems to cause
Data CRC errors.
Value was derived from analyzing hardware signals after
Raspberry Pi is powered up. Before any data is read though DATA line
adapter's clock frequency is changed to 8MHz.
Modern cards should function fine at 8MHz but for older MMC cards it
can be overriden by setting hw.bcm2835.sdhci.min_freq tunable.
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
Major changes:
* Finally tracked down the flow control setting that
seems to have been causing TX stalls and watchdog timeouts
* RX and TX paths now share a lot more code
* TX interrupt is no longer used; we instead GC finished
tx queue entries at the bottom of the start routine.
* TX start now queues fragmented packets directly; it only
invokes defrag() for occasional very fragmented packets.
* "sysctl dev.cpsw" dumps controller statistics and queue counts
* Host Error Interrupt will give extensive debugging information
if the controller chokes on the queued data.
VM_KMEM_SIZE_SCALE specifies which fraction of the available physical
memory, after deduction of the kernel itself and other early statically
allocated memory, can be used for the kmem_map. The kmem_map provides
for all UMA/malloc allocations in KVM space.
Previously ARM was using a fixed kmem_map size of (12*1024*1024) = 12MB
without regard to effectively available memory. This is too small for
recent ARM SoC with more than 128MB of RAM.
For reference a description of others related kmem_map parameters:
VM_KMEM_SIZE default start size of kmem_map if SCALE is
not defined
VM_KMEM_SIZE_MIN hard floor on the kmem_map size
VM_KMEM_SIZE_MAX hard ceiling on the kmem_map size
VM_KMEM_SIZE_SCALE fraction of the available real memory to
be used for the kmem_map, limited by the
MIN and MAX parameters.
Tested by: ian
MFC after: 1 week
In all the routines that loop through a range of virtual addresses, the loop
is controlled by subtracting the cache line size from the total length of the
request. After the subtract, a 'bpl' instruction was used, which branches if
the result of the subtraction is zero or greater, but we need to exit the
loop when the count hits zero. Thus, all the bpl instructions in those loops
have been changed to 'bhi' (branch if greater than zero).
In addition, the two routines that walk through the cache using set-and-index
were correct, but confusing. The loop control for those has been simplified,
just so that it's easier to see by examination that the code is correct.
Routines for other arm architectures and generations still have the bpl
instruction, but compensate for the off-by-one situation by decrementing
the count register by one before entering the loop.
PR: arm/174461
Approved by: cognet (mentor)
This adds support for version 10, revision 01, but it should also work
without changes for the 0901 model, at least until we get drivers for the
two different wifi chips involved.
Many users contributed to and tested the various patchsets floating around
for the past year that have eventually evolved into this checkin, most notably
Richard Neese who provided the bulk of the kernel config file.
Approved by: cognet (mentor)
so that we don't need an empty implementation of it for every Marvell platform
that has no PCI. This allows the removal of the SheevaPlug-specific stub and
config files, and eliminates the need to add similar stubs for future models.
Marvell platforms that do expose PCI are compiled with 'device pci' which
causes the real (non-weak) implementation in dev/fdt/fdt_pci.c to be used.
Approved by: cognet (mentor)
the prior commit. Use essentially the same sprintf() statement for both
formatting and pre-formatting, and use a format string which eliminates the
need for an extra temporary buffer when formatting the name.
Noted by: Christoph Mallon
Pointy hat to: ian
Approved by: cognet (mentor)
interrupt counts and names, by making the names into an array of fixed-length
strings that can be directly indexed. This eliminates extra memory accesses
on every interrupt to increment the counts.
As a side effect, it also fixes a bug that would corrupt the names data
if a name was longer than MAXCOMLEN, which led to incorrect vmstat -i output.
Approved by: cognet (mentor)
