This fixes a dependency of mac_label.c on namespace pollution in
<vm/uma.h>.
Similarly for SYSCTL_DECL() although I had no problems with it. This
probably makes some includes of <sys/sysctl.h> bogus.
longer uses these interrupt vectors for its ISA interrupt pins, so these
entries will not be overwritten. If we get a spurious interrupt from the
ATPIC when using the APIC, it will be treated as a stray interrupt instead
of causing a panic.
Short description of ip_fastforward:
o adds full direct process-to-completion IPv4 forwarding code
o handles ip fragmentation incl. hw support (ip_flow did not)
o sends icmp needfrag to source if DF is set (ip_flow did not)
o supports ipfw and ipfilter (ip_flow did not)
o supports divert, ipfw fwd and ipfilter nat (ip_flow did not)
o returns anything it can't handle back to normal ip_input
Enable with sysctl -w net.inet.ip.fastforwarding=1
Reviewed by: sam (mentor)
of depending on namespace pollution 2 layers deep in <vm/uma.h>. Fixed
most nearby include messes (another like this, several the opposite of
this, and some formatting).
be printed, if the module were loaded into a kernel which had INET6 enabled.
The gre(4) driver does not use INET6, nor is it specified for IPv6. The
tunnel_status() function in ifconfig(8) is somewhat overzealous and assumes
that all tunnel interfaces speak KAME ifioctls.
This fix follows the path of least resistance, by teaching gre(4) about
the two KAME ifioctls concerned.
PR: bin/56341
- Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff
range. The pmap lazyfix IPI was reordered down next to the TLB
shootdowns to avoid conflicting with the spurious interrupt vector.
- Move the base of APIC interrupts up 16 so that the first 16 APIC
interrupts do not overlap the vectors used by the ATPIC.
- Remove bogus interrupt vector reservations for LINT[01].
- Now that 0xc0 - 0xef are available, use them for device interrupts.
This increases the number of APIC device interrupts to 191.
- Increase the system-wide number of global interrupts to 191 to catch up
to more APIC interrupts.
Requested by: peter (2)
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
in exit1(), make sure the p_klist is empty after sending NOTE_EXIT.
The process won't report fork() or execve() and won't be able to handle
NOTE_SIGNAL knotes anyway.
This fixes some race conditions with do_tdsignal() calling knote() while
the process is exiting.
Reported by: Stefan Farfeleder <stefan@fafoe.narf.at>
MFC after: 1 week
- In the receive routine handle the case where last descriptor could have
less than 4 bytes of data.
- Handle race between detach/ioctl routine.
MFC after: 3 days
kernel build. This makes it possible for me not to get pissed off that
random.ko crashes the system trying to rdtsc() when the i386/cpu.h
support code decides it's okay to call that op when neither I386_CPU or
I486_CPU is defined. I guess it also makes WITNESS/INVARIANTS defines
get picked up by the modules.
vnode of the parent. However, this check should not be performed if
the lookup failed. This change should fix "union_lookup returning
. not same as startdir" panics people were seeing. The bug was
introduced by an incomplete import of a NetBSD delta in rev 1.38.
- Move the aforementioned check out from DIAGNOSTIC. Performance
is the least of our unionfs worries.
- Minor reorganization.
PR: 53004
MFC after: 1 week
- Return EBUSY if the region was wired by mlock(2) and MS_INVALIDATE
is specified to msync(2). This is required by the Open Group Base
Specifications Issue 6.
- vm_map_sync() doesn't return KERN_FAILURE. Thus, msync(2) can't
possibly return EIO.
- The second major loop in vm_map_sync() handles sub maps. Thus,
failing on sub maps in the first major loop isn't necessary.
any functions that call them. Calling proc_rwmem() with the proc lock
held is not safe. Currently, we're protected from any races by Giant.
Eventually proc_rwmem() should require the proc lock and not Giant.
parts of ptrace using proc_rwmem(). proc_rwmem() requires giant, and
giant must be acquired prior to the proc lock, so ptrace must require giant
still.
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
Give the HZ/overflow check a 10% margin.
Eliminate bogus newline.
If timecounters have equal quality, prefer higher frequency.
Some inspiration from: bde
5212-based devices because PHY errors are used to collect data
on environmental noise that and doesn't truly reflect the state
of the communications media. The result is confused users.
Folks that want to watch PHY errors can still get the statistics
through the device ioctl (used by athstats).
o reject scan requests for a device that isn't marked up
This fixes a problem where requesting a scan before marking the device
up would cause a panic because the current channel was set to "any" (0xffff).
o correct a read-lock assert in in_pcblookup_local that should be
a write-lock assert (since time wait close cleanups may alter state)
Supported by: FreeBSD Foundation
preemption two CPUs can be in the same function at the same time
and clobber each others variables. Remove register declaration
from local variables.
Reviewed by: sam (mentor)
and empty its turnstile while the blocking threads still pointed to the
turnstile. If the thread on the first CPU blocked on a lock owned by
one of the threads blocked on the turnstile just woken up, then the
first CPU could try to manipulate a bogus thread queue in the turnstile
during priority propagation.
- Update locking notes for ts_owner and always clear ts_owner, not just
under INVARIANTS.
Tested by: sam (1)
deleted in 1.81. Increase the initial timeout limit to 2ms to
eliminate spurious messages of excessive timeouts in the NFS
client code.
Requested by: Poul-Henning Kamp <phk@phk.freebsd.dk>
Requested by: Mike Silbersack <silby@silby.com>
Requested by: Sam Leffler <sam@errno.com>
Giant and is also MPSAFE.
Push Giant further down into __mac_get_fd() and __mac_set_fd(),
grabbing it only for constrained regions dealing with VFS, and
dropping it entirely for operations related to labeling of pipes.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
Radeon IGP support (still lacking PCI IDs), and DRM interface 1.2 updates which
include finally tying the DRM instances to specific devices rather than relying
on the X Server.
This switch toggles between strict multicast delivery, and traditional
multicast delivery.
The traditional (default) behaviour is to deliver multicast datagrams to all
sockets which are members of that group, regardless of the network interface
where the datagrams were received.
The strict behaviour is to deliver multicast datagrams received on a
particular interface only to sockets whose membership is bound to that
interface.
Note that as a matter of course, multicast consumers specifying INADDR_ANY
for their interface get joined on the interface where the default route
happens to be bound. This switch has no effect if the interface which the
consumer specifies for IP_ADD_MEMBERSHIP is not UP and RUNNING.
The original patch has been cleaned up somewhat from that submitted. It has
been tested on a multihomed machine with multiple QuickTime RTP streams
running over the local switch, which doesn't do IGMP snooping.
PR: kern/58359
Submitted by: William A. Carrel
Reviewed by: rwatson
MFC after: 1 week
vector stubs and into the C functions they call.
- Move disabling and EOIing of interrupt sources out of PIC driver entry
points and into intr_execute_handlers(). Intr_execute_handlers() only
disables a source for an interrupt if it is a stray interrupt or has
threaded handlers. Sources with fast handlers no longer disable (mask)
the source while executing the handlers.
- Move the setting of clkintr_pending into intr_execute_handlers() and set
the variable for any interrupt source with a vector of 0. (Should only
be true for IRQ 0.) This fixes clkintr_pending in the NO_MIXED_MODE
case.
- Implement lapic_eoi() and use it to implement ioapic_eoi_source().
- Rename atpic_sched_ithd() to atpic_handle_intr() since it is used to
handle all atpic interrupts and not just threaded ones.
Inspired by: peter's changes to amd64 in p4 (1)
Requested by: bde (2)
extra argument to the devfs MAC policy entry points was accidentally
merged from the MAC branch during my earlier commit to these policies,
and is not scheduled to be merged just yet.
defines for these constants that include the trailing NUL byte. These
new constants have SIZ in their name instead of LEN. As soon as all
consumers in the tree are converted to use the new defines the old
defines will be put under BURN_BRIDGES.
Reviewed by: archie, julian, ru
Approved by: re (in principle)
after the additions made for the new statfs structure (version
1.157). These must be updated in a separate checkin after
syscalls.master has been checked in so that they reflect its
new CVS identity. As these are purely derived files, it is not
clear to me why they are under CVS at all. I presume that it has
something to do with having `make world' operate properly.
accurate reporting of multi-terabyte filesystem sizes.
You should build and boot a new kernel BEFORE doing a `make world'
as the new kernel will know about binaries using the old statfs
structure, but an old kernel will not know about the new system
calls that support the new statfs structure. Running an old kernel
after a `make world' will cause programs such as `df' that do a
statfs system call to fail with a bad system call.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Tim Robbins <tjr@freebsd.org>
Reviewed by: Julian Elischer <julian@elischer.org>
Reviewed by: the hoards of <arch@freebsd.org>
Sponsored by: DARPA & NAI Labs.
in various kernel objects to represent security data, we embed a
(struct label *) pointer, which now references labels allocated using
a UMA zone (mac_label.c). This allows the size and shape of struct
label to be varied without changing the size and shape of these kernel
objects, which become part of the frozen ABI with 5-STABLE. This opens
the door for boot-time selection of the number of label slots, and hence
changes to the bound on the number of simultaneous labeled policies
at boot-time instead of compile-time. This also makes it easier to
embed label references in new objects as required for locking/caching
with fine-grained network stack locking, such as inpcb structures.
This change also moves us further in the direction of hiding the
structure of kernel objects from MAC policy modules, not to mention
dramatically reducing the number of '&' symbols appearing in both the
MAC Framework and MAC policy modules, and improving readability.
While this results in minimal performance change with MAC enabled, it
will observably shrink the size of a number of critical kernel data
structures for the !MAC case, and should have a small (but measurable)
performance benefit (i.e., struct vnode, struct socket) do to memory
conservation and reduced cost of zeroing memory.
NOTE: Users of MAC must recompile their kernel and all MAC modules as a
result of this change. Because this is an API change, third party
MAC modules will also need to be updated to make less use of the '&'
symbol.
Suggestions from: bmilekic
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
vfs_mount_alloc/vfs_mount_destroy functions and take care to completely
destroy the mount point along with its locks. Mount struct has grown in
coplexity recently and depending on each failure path to destroy it
completely isn't working anymore.
2. Eliminate largely identical vfs_mount and vfs_unmount question by
moving the code to handle both cases into a newly introduced vfs_domount
function.
3. Simplify nfs_mount_diskless to always expect an allocated mount
struct and never attempt an allocation/destruction itself. The
vfs_allocroot allocation was there to support 'magic' swap space
configuration for diskless clients that was already removed by PHK some
time ago.
4. Include a vfs_buildopts cleanups by Peter Edwards to validate the
sanity of nmount parameters passed from userland.
Submitted by: (4) Peter Edwards <peter.edwards@openet-telecom.com>
Reviewed by: rwatson
important change is in cpu_switch() where we disable the high FP
registers for the thread that we switch-out if the CPU currently
has its high FP registers. This avoids that the high FP registers
remain enabled for the thread even when the CPU has unloaded them
or the thread migrated to another processor.
Likewise, when we switch-in a thread of that has its high FP
registers on the CPU, we enable them. This avoids an otherwise
harmless, but unnecessary trap to have them enabled.
The code that handles the disabled high FP trap (in trap()) has
been turned into a critical section for the most part to avoid
being preempted. If there's a race, we bail out and have the
processor trap again if necessary.
Avoid using the generic ia64_highfp_save() function when the
context is predictable. The function adds unnecessary overhead.
Don't use ia64_highfp_load() for the same reason. The function
is now unused and can be removed.
These changes make the lazy context switching of the high FP
registers in an UP kernel functional.
turnstiles to implement blocking isntead of implementing a thread queue
directly. These turnstiles are somewhat similar to those used in Solaris 7
as described in Solaris Internals but are also different.
Turnstiles do not come out of a fixed-sized pool. Rather, each thread is
assigned a turnstile when it is created that it frees when it is destroyed.
When a thread blocks on a lock, it donates its turnstile to that lock to
serve as queue of blocked threads. The queue associated with a given lock
is found by a lookup in a simple hash table. The turnstile itself is
protected by a lock associated with its entry in the hash table. This
means that sched_lock is no longer needed to contest on a mutex. Instead,
sched_lock is only used when manipulating run queues or thread priorities.
Turnstiles also implement priority propagation inherently.
Currently turnstiles only support mutexes. Eventually, however, turnstiles
may grow two queue's to support a non-sleepable reader/writer lock
implementation. For more details, see the comments in sys/turnstile.h and
kern/subr_turnstile.c.
The two primary advantages from the turnstile code include: 1) the size
of struct mutex shrinks by four pointers as it no longer stores the
thread queue linkages directly, and 2) less contention on sched_lock in
SMP systems including the ability for multiple CPUs to contend on different
locks simultaneously (not that this last detail is necessarily that much of
a big win). Note that 1) means that this commit is a kernel ABI breaker,
so don't mix old modules with a new kernel and vice versa.
Tested on: i386 SMP, sparc64 SMP, alpha SMP
- Fail in agp_alloc_gatt if the aperture size is 0 instead of panicing in
contigmalloc.
Reported by: Bjoern Fischer <bfischer@Techfak.Uni-Bielefeld.DE>
Reviewed by: jhb
MFC after: 1 week
interrupt such as IRQ 22 or 19. However, the ACPI BIOS still routes
interrupts from some PCI devices to the same intpin calling the pin
IRQ 22. Thus, ACPI expects to address a single interrupt source via two
different names. To work around this, if the SCI is remapped to a non-ISA
interrupt (i.e., greater than 15), then we use
acpi_OverrideInterruptLevel() function to tell ACPI to use IRQ 22 or 19
rather than IRQ 9 for the SCI.
Previously we would change IRQ 22 or 19's name to IRQ 9 when we encountered
such an Interrupt Source Override entry in the MADT which routed the SCI
properly but left PCI devices mapped to IRQ 22 or 19 w/o a routable
interrupt.
Tested by: sos
This ensures that uart gets a higher console priority than syscons when
a serial console is being used. Testing against the "console" environment
variable doesn't make sense since we only have one loader console driver.
should now only have HTT CPUs if they have explicitly asked for them
either by enabling HyperThreading in the BIOS or by using the
MPTABLE_FORCE_HTT kernel option.
should only be used if they are enabled in the BIOS. Now that we support
enumerating CPUs using the ACPI MADT, any HTT machine using ACPI should
respect the BIOS setting. For HTT machines with ACPI disabled in the
kernel, the MPTABLE_FORCE_HTT kernel option can be used to try to probe HTT
CPUs like have done in the past for the MP Table case. This option should
only be enabled if HTT is enabled in the BIOS.
that we currently do not keep track of whether the thread has
actually used the high FP registers before. If not, we should
not save them in the context which automaticly means that we
also would not restore them from the context. For now, do it
unconditionally so that we can reach functional completeness.
functions switched to using {g|s}et_mcontext(). The problem is that
sigreturn(), being a syscall, can be given an async. context (i.e.
one corresponding to an interrupt or trap). When this happens, we
try to return to user mode via epc_syscall_return with a trapframe
that can only be used to return to user mode via exception_restore.
To fix this, we check the frame's flags immediately prior to
epc_syscall_return and branch to exception_restore for non-syscall
frames. Modify the assertion in set_mcontext() to check that if
there's a mismatch, it's because of sigreturn().
ktr_resize_pool(); this eliminates a potential livelock.
Return ENOSPC only if we encountered an out-of-memory condition when
trying to increase the pool size.
Reviewed by: jhb, bde (style)
cache after a data access error we must discard all cache lines. When
disabled existing cache lines are not invalidated by stores to memory, so
we risk reading stale data that was cached before the data access error if
we don't flush them. This is especially fatal when the memory involved
is the active part of the kernel or user stack. For good measure we also
flush the instruction cache.
This fixes random crashes when the X server probes the PCI bus through
/dev/pci.
commit broke the world because it depended on namespace pollution that
was only in my version of <machine/bootinfo.h>. The include was removed
in rev.1.63 after the last reference to it went away in rev.1.61.
dsp_open: rearrange to only hold one lock at a time
dsp_close: ditto
mixer_hwvol_init: delete locking, the only consumer seems to
be the ess driver and it only call it a creation time, I
think the device will be stable across the sleepable malloc.
cmi interrupt routine: Release locks while caller chn_intr,
either this or do what emu10k1 does which is have no locks
at in the interrupt handler.
Submitted by: mat@cnd.mcgill.ca
consistency initialized. Consequently, a number of conditionals that
checked the validity of b_object before passing it to VM_OBJECT_LOCK()
and VM_OBJECT_UNLOCK() are no longer needed.
The reason this was done was to avoid a race to the root when an
NFS server went down. However a semi-recent change to the way that
the kernel's lookup() routine traverses mount points prevents this.
Rev 1.39 of vfs_lookup.c changed the ordering of locks such that we
aquire a shared lock on the mount point being accessed and then drop
the directory vnode lock before requesting the target lock.
With that in place we no longer need shared locks for NFS to prevent
race to the root lockups.
it is marked as RTF_UP. This appears to fix a crash that was sometimes
triggered when dhclient(8) tried to send a packet after an interface
had been detatched.
Reviewed by: sam
a resource leak. Move the resource deallocation code from fifo_close()
to a new function, fifo_cleanup(), and call fifo_cleanup() from
fifo_close() and the appropriate places in fifo_open().
Tested by: Lukas Ertl
Pointy hat to: truckman
because RFNOWAIT was being passed to kproc_create.
The result was that shutdown took quite a bit longer because this
errant "child" would not respond to termination signals from init
at system shutdown.
RFNOWAIT dissassociates itself from the caller by attaching to init
as a parent proc. We could have had the taskqueue proc listen for
SIGKILL, but being able to SIGKILL a potentially critical system
process doesn't seem like a good idea.
comment about this flag in rev.1.61. It is not historical like the
comment said; it is the flag that says that most of what is laboriously
put in the bootinfo struct is actually there. Newer kernels were
bootable by even the broken boot2 without losing anything except the
symbol table, but older kernels need at least the memory sizes.
Restoring the "|" with RB_BOOTINFO that was lost in rev.1.43 costs 5
bytes. The fix can be done in only 4 bytes by fixing some code that
was removed in rev.1.61 (put RB_BOOTINFO back in in the initial value
of "opts" and fix RBX_MASK to not clobber it.)
crashes that had sn0 as the irq that's being serviced, when there was
no sn0 in the system. This seems to prevent them. Also, we want to
wait until after we've registered with the network layer before we
turn on the interrupt spigot to avoid races.
- redo updating.
rijndael-api-fst.[ch]:
- switch to use new low level rijndael api.
- stop using u8, u16 and u32.
- space cleanup.
Tested by: gbde(8) and phk's test program
free one sem_undo with un_cnt == 0 instead of all of them. This is a
temporary workaround until the SLIST_FOREACH_PREVPTR loop gets fixed so
that it doesn't cause cycles in semu_list when removing multiple adjacent
items. It might be easier to just use (doubly-linked) LISTs here instead
of complicated SLIST code to achieve O(1) removals.
This bug manifested itself as a complete lockup under heavy semaphore use
by multiple processes with the SEM_UNDO flag set.
PR: 58984
Only update them in the newly created context to reflect the state
after copying the dirty registers onto the user stack. If we were to
update the trapframe, we lose the state at entry into the kernel. We
may need that after we create the context, such as for KSE upcalls.
We have to update the trapframe after writing the dirty registers to
the user stack for signal delivery to work. But this is best done in
sendsig() itself where it applies, not in get_mcontext() where it's
done unconditionally.
with debugger, so testing P_TRACED in SIGPENDING is useless. This test also
is the culprit which causes lots of 'failed to set signal flags properly for
ast()' to be printed on console which is just a false complaint.
must return EINVAL if size is zero. Submitted by: tegge
- In order to avoid a race condition in multithreaded applications, the
check and removal operations by munmap(2) must be in the same critical
section. To accomodate this, vm_map_check_protection() is modified to
require its caller to obtain at least a read lock on the map.
revision 1.142
date: 2003/10/11 03:04:26; author: toshii
Fix a done list handling bug which exhibits under high shared
interrupt rate and bus traffic. As the interrupt register is
read after checking hcca_done_head, there was a small chance
of dropping a done list. Ignore OHCI_WDH interrupt bit if
hcca_done_head is zero so that OHCI_WDH is processed later.
revision 1.141
date: 2003/09/10 20:08:29; author: mycroft;
Update actlen even in the case where a TD returns an error --
this is critical for the umass bulk-only STALL case.
revision 1.176
date: 2003/11/04 19:11:21; author: mycroft;
Ignore a CRCTO error on a SETUP transaction in combination with
STALLED or NAK. This fixes problems with the GL641.
- remove the unnecessary elm arg from SIMPLEQ_REMOVE_HEAD().
this mirrors the functionality of SLIST_REMOVE_HEAD() (the other
singly-linked list type) and FreeBSD's STAILQ_REMOVE_HEAD()
use set_mcontext() to restore the context in sigreturn(). Since we
put the syscall number and the syscall arguments in the trapframe
(we don't save the scratch registers for syscalls, which allows us
to reuse the space to our advantage), create a MD specific flag so
that we save the scratch registers even for syscalls. We would not
be able to restart a syscall otherwise.
The signal trampoline does not need to flush the regiters anymore,
because get_mcontext() already handles that. In fact, if we set up
the context correctly, we do not need to have a trampoline at all.
This change however only minimally changes the trampoline code. In
follow-up commits this can be further optimized.
Note that normally we preserve cfm and iip in the trapframe created
by the EPC syscall path when we restore a context in set_mcontext()
because those fields are not normally set for a synchronuous context.
The kernel puts the return address and frame info of the syscall
stub in there. By preserving these fields we hide this detail from
userland which allows us to use setcontext(2) for user created
contexts. However, sigreturn() is commonly called from the trampoline,
which means that if we preserve cfm and iip in all cases, we would
return to the trampoline after the sigreturn(), which means we hit
the safety net: we call exit(2). So, we do not preserve cfm and iip
when we have a synchronous context that also has scratch registers
(the uncommon context created by sendsig() only), under the assumption
that if such a context is created in userland, something special is
going on and the use of cfm and iip is then just another quirk. All
this is invisible in the common case.
if we drop into the pmap or vnode layers.
- Migrate the handling of zero-length msync(2)s into vm_map_sync() so that
multithread applications can't change the map between implementing the
zero-length hack in msync(2) and reacquiring the map lock in
vm_map_sync().
Reviewed by: tegge
Since all callers either passed 0 or 1 for clear_ret, define bit 0 in
the flags for use as clear_ret. Reserve bits 1, 2 and 3 for use by MI
code for possible (but unlikely) future use. The remaining bits are for
use by MD code.
This change is triggered by a need on ia64 to have another knob for
get_mcontext().
o When we're resetting the board, make sure that we error out the pending
CCBs first. Otherwise the aha_cmd won't accept further commands, such
as those that are used to reset the card (AOP_INITIALIZE_MBOX). This
appears to cause a cascade failure where no more commands are possible
to the card.
o Reduce from 10s down to 1s the amount of time we're willing to tolerate
the card being awol. This helps the above case.
o Add some error checking to two commands issued in the probe.
I have a dim memory of gibbs@ trying to tell me about this problem a
few years ago, so pointy hat to imp@ for sitting on it so long.
in the log message for kern_sched.c 1.83 (which should have been
repo-copied to preserve history for this file), the (4BSD) scheduler
algorithm only works right if stathz is nearly 128 Hz. The old
commit lock said 64 Hz; the scheduler actually wants nearly 16 Hz
but there was a scale factor of 4 to give the requirement of 64 Hz,
and rev.1.83 changed the scale factor so that the requirement became
128 Hz. The change of the scale factor was incomplete in the SMP
case. Then scheduling ticks are provided by smp_ncpu CPUs, and the
scheduler cannot tell the difference between this and 1 CPU providing
scheduling ticks smp_ncpu times faster, so we need another scale
factor of smp_ncp or an algorithm change.
This quick fix uses the scale factor without even trying to optimize
the runtime divisions required for this as is done for the other
scale factor.
The main algorithmic problem is the clamp on the scheduling tick counts.
This was 295; it is now approximately 295 * smp_ncpu. When the limit
is reached, threads get free timeslices and scheduling becomes very
unfair to the threads that don't hit the limit. The limit can be
reached and maintained in the worst case if the load average is larger
than (limit / effective_stathz - 1) / 2 = 0.65 now (was just 0.08 with
2 CPUs before this change), so there are algorithmic problems even for
a load average of 1. Fortunately, the worst case isn't common enough
for the problem to be very noticeable (it is mainly for niced CPU hogs
competing with less nice CPU hogs).
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
that msync(2) is its only caller.
- Migrate the parts of the old vm_map_clean() that examined the internals
of a vm object to a new function vm_object_sync() that is implemented in
vm_object.c. At the same, introduce the necessary vm object locking so
that vm_map_sync() and vm_object_sync() can be called without Giant.
Reviewed by: tegge
are zx1 based machines and they don't particularly like it when we
poke at them with PC legacy code. The atkbd and psm devices were
disabled in the hints file so that one could enable them on machines
that support legacy devices, but that's not really something you can
expect from a first-time installer. This still leaves syscons (sc)
and the vga device, which were enabled by default and wrecking havoc
anyway. We could disable them by default like the atkbd and psm
devices, but there's really no point in pretending we're in a better
shape that way.
o pickup Giant in divert_packet to protect sbappendaddr since it
can be entered through MPSAFE callouts or through ip_input when
mpsafenet is 1
o add missing locking on output
o add locking to abort and shutdown
o add a ctlinput handler to invalidate held routing table references
on an ICMP redirect (may not be needed)
Supported by: FreeBSD Foundation
o add assertions in tcp_respond to validate inpcb locking assumptions
o use local variable instead of chasing pointers in tcp_respond
Supported by: FreeBSD Foundation
whether or not the isr needs to hold Giant when running; Giant-less
operation is also controlled by the setting of debug_mpsafenet
o mark all netisr's except NETISR_IP as needing Giant
o add a GIANT_REQUIRED assertion to the top of netisr's that need Giant
o pickup Giant (when debug_mpsafenet is 1) inside ip_input before
calling up with a packet
o change netisr handling so swi_net runs w/o Giant; instead we grab
Giant before invoking handlers based on whether the handler needs Giant
o change netisr handling so that netisr's that are marked MPSAFE may
have multiple instances active at a time
o add netisr statistics for packets dropped because the isr is inactive
Supported by: FreeBSD Foundation
PALM_4 initialisation hack. I've not confirmed it myself, but
seeing as we already don't use it for the Sony Clie_41, let's drop
it from the Clie_40 also and see what happens.
(Question: What about the Clie_S360 and Clie_NX60 devices? Do we
need to drop Palm4 from those as well? Possibly, but I've not had
any reports about those so I don't know.)
PR: kern/56575
MFC after: 3 days
is highly MD in an emulation environment since it operates on the host
environment. Although the setregs functions are really for exec support
rather than signals, they deal with the same sorts of context and include
files. So I put it there rather than create yet another file.
since there is no direct association between M:N thread and kse,
sometimes, a thread does not have a kse, in that case, return a pctcpu
from its last kse, it is not perfect, but gives a good number to be
displayed.
pmap_pte() and pmap_pte_quick(). The distinction being based upon the
locks that are held by the caller. When the given pmap is not the
current pmap, pmap_pte() should be used when Giant is held and
pmap_pte_quick() should be used when the vm page queues lock is held.
- When assigning to PMAP1 or PMAP2, include PG_A anf PG_M.
- Reenable the inlining of pmap_is_current().
In collaboration with: tegge
has a LOR between IPFW inpcb locks but I'm committing it now as the
lesser of two evils (the other being unlocked use of in_pcblookup).
Supported by: FreeBSD Foundation
successfully initialized in the label as a socket peer label, not a
socket label. For current policy modules, this didn't make a
difference, but if a policy module had label data in the peer label
that was to be GC'd in a different way than the normal socket label,
it might have been a problem.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
that it was obsoleted. it is better to fail than just hiding use
of ipsec_gethist() at build.
Sugessted by: "Bjoern A. Zeeb" <bzeeb-lists@lists.zabbadoz.net>
