was found, or if there was a checksum mismatch.
This patch should allow the driver to be used with any AMD 53c974
based SCSI card, or with the AMD SCSI+Ethernet Combo Chip found on
some motherboards.
Use the interface MTU instead of the constant when deciding what
packets to accept.
Allow using the SIOCSIFMTU ioctl (e.g. "ifconfig tun0 mtu XXX") to
set the MTU.
These controllers are based on the AMD 53c974, and the driver
does only support those two cards, since it checks for a Tekram
specific configuration EEPROM.
This deficiency (TM) will be fixed soon ... :)
This code is:
(C)Copyright 1995-1996 Tekram Technology Co., Ltd.
Obtained from: Tekram
EISA slots to probe. This is mainly intended to allow installing the
system on an HP Netserver with an on-board AIC7xxx EISA SCSI
controller, that is sitting on EISA slot # 11.
Documentation updates explaining this hack will follow shortly.
Note that this can go away again as soon as the EISA device probing
is more intelligent about the address space clash with the PCI address
space.
2.2 candidate.
Not objected by: freebsd-core :)
that we do allow mlock to span unallocated regions (of course, not
mlocking them.) We also allow mlocking of RO regions (which the old
code couldn't.) The restriction there is that once a RO region is
wired (mlocked), it cannot be debugged (or EVER written to.)
Under normal usage, the new mlock code will be a significant improvement
over our old stuff.
Tekram DC390W/U/F, whose config EEPROM can now be dumped, if the kernel
is built with option NCR_TEKRAM_EEPROM.
Other changes:
- add brackets to expansion of OUTB/W/L macro arguments.
- remove unused NCB structure element ns_async
- support sync. SCSI offset of 16 (instead of only 8) on 825A and 875
- correctly identify 53c810A and 53c825A chips
- preserve SCSI BIOS settings of PCI performance options
- remove (already disabled) support for NCR reset because of command timeout
- reverse order of reading of SCSI and DMA specific interrupt cause registers
- add definition of Tekram config EEPROM contents (not currently used)
to TAILQs. Fix places which referenced these for no good reason
that I can see (the references remain, but were fixed to compile
again; they are still questionable).
the profiling level in config and decide what to do in makefiles.
Makefile.i386:
Align functions to 16-byte boundaries if profiling is enabled. This
will allow a fourfold reduction in the size of the profiling buffers.
I've added an installation from optical disk drive facility.
This enables FreeBSD to be installed from an optical disk, which
may be formatted in "super floppy" style or sliced into MSDOS-FS
and UFS partitions.
Note: ncr.c should be reviewed by Stefan Esser <se@freebsd.org>
and cd.c by Joerg Wunsch <joerg@freebsd.org> before bringing this
into 2.2.
Submitted-By: Shunsuke Akiyama <akiyama@kme.mei.co.jp>
series drives, and add the NAKAMICHI MO drive RMD-5200-S.
Closes PR # kern/2200: Change/Add new optical di...
Submitted by: akiyama@kme.mei.co.jp (Shunsuke Akiyama)
makerom checksum check calculation was a no-op
nb8390.c had a bug which caused packet_len to be incorrect
for packets which wrapped in the buffer.
Submitted by: Linux developers (I lost the email with their names)
makes MADV_SEQUENTIAL much more effective. I suggest that
we start using MADV_SEQUENTIAL on system utilities that mmap
their input files, and the I/O is predominantely sequential.
Below is a test with 'cmp' on two relatively large binary files,
where the files are so large that the caching is ineffective:
+ ls -l t1.xxx t2.xxx
-rw-r--r-- 1 root wheel 65598384 Dec 10 12:13 t1.xxx
-rw-r--r-- 1 root wheel 65598384 Dec 10 12:14 t2.xxx
+ time cmp t1.xxx t2.xxx
3.78user 0.70system 1:33.43elapsed 4%CPU
+ time cmpmadv t1.xxx t2.xxx
4.21user 1.05system 0:30.93elapsed 17%CPU
This change is as a result of an observation made by BDE.
partition is 0, which is outside the slice unless the disk is
dangerously dedicated. There is little error checking later, and
following garbage metadata outside the slice usually caused crashes,
Empty 'a' partitions are fairly easy to create by cloning the label
for the whole disk.
Fixed a missing newline in a related error message.
type to be int so that errors can be returned.
2) Use the new SIOCSIFMTU ether_ioctl support in the few drivers that are
using ether_ioctl().
3) In if_fxp.c: treat if_bpf as a token, not as a pointer. Don't bother
testing for FXP_NTXSEG being reached in fxp_start()...just check for
non-NULL 'm'. Change fxp_ioctl() to use ether_ioctl().
ACTUALLY_LKM_NOT_KERNEL until the real fix comes through. Whatever
flag that is used to indicate building LKMs will have be be substituted
in the future. This allows proper selection of the usage of the
efficient, single instruction in the kernel, but alas, doesn't allow
for use in userland or LKMs :-(. Them's the breaks!!!
with one of the following (I486_CPU,I586_CPU,I686_CPU) so it can take
advantage of the very quick bswap insn. This keeps LKMs from being
built to take advantage of the insn, but also makes sure that the LKMs
can be run on all CPUs. (The LKMs don't pick up the CPU options :-( ).
that map entries are coalesced when appropriate. Also, conditionalize
some code that is currently not used in vm_map_insert. This mod
has been added to eliminate unnecessary map entries in buffer map.
Additionally, there were some cases where map coalescing could be done
when it shouldn't. That problem has been resolved.
modules sort of works now. Their devswitch entries aren't cleaned
up, so accessing them after they have been unloaded causes a panic
in spec_open().
Submitted by: durian@plutotech.com (Mike Durian), IIRC
line with BSD/OS and Linux's username limits, making transitioning from
either operating system a lot easier than it is now. I'm currently
running with this change on my system, as are several others, and have
experienced no ill effects.
This is not for 2.2! This needs to get shaken out longer term in 3.0.
Previously-approved-by: davidg
to miss reselections from some devices and since the reselection response
timeout is only 200ns, enabling reselections too late may be the cause of our
problem.
function ed_attach_NE2000_pci() in if_ed.c passes
an uninitialized block of memory (got with malloc())
to ed_attach. This prevents a proper initialization
of the device descriptor and in my case causes a panic
during the probe, while printing out device info.
Reviewed by: phk
Submitted by: Luigi Rizzo <luigi@iet.unipi.it>
list of IP setsockopts the Linux emulator recognizes.
Explicitly disallow IP_HDRINCL since Linux's handling of
raw output is different than BSD's.
Closes PR#kern/2111.
Submitted by: y-nakaga@ccs.mt.nec.co.jp (Yoshihisa NAKAGAWA)
1/ increase the tun MTU from 1500 to 1600 to allow it to be used with
packets formatted according to RFC1490 and RFC1717
2/ allow the tsleep() when reading, to be interruptable by signals
so that one can now do:
od -xc </dev/tun0
to dump packets for debugging without getting hung.
Passed on by: Archie@whistle.com (archie Cobbs)
Nice but not neccessary in 2.2
1. 'connector_table' is shortened to 'conn_tab'.
2. More reliable connector change code.
3. Display message like "vx0: selected bnc. (link1)"
when the connector changed by link[012].
4. Handle MII properly.
5. Potentially slightly better performance.
6. Fixed a silly typo.
Submitted by: Naoki Hamada <nao@sbl.cl.nec.co.jp>
1. 'connector_table' is shortened to 'conn_tab'.
2. More reliable connector change code.
3. Display message like "vx0: selected bnc. (link1)"
when the connector changed by link[012].
4. Handle MII properly.
5. Potentially slightly better performance.
6. Fixed a silly typo.
Submitted by: Naoki Hamada <nao@sbl.cl.nec.co.jp>
1. All the suggestions earlier made by Bruce: renaming some symbols,
stricter error checking, removing redundant code, etc.
2. The `psm' driver preserves the default counter resolution and
report rate, whatever they are after reset. (Based on reports and
suggestion from Nate and Rob Bolin).
3. The `psm' driver now does not check the so-called sync. bit in the
first byte of the data packet by default, so that the tapping feature
of ALPUS GlidePoint works (based on reports from Louis Mamakos). I
tested the code with ALPUS Desktop GlidePoint (M/N GP101) and found
no problem; tapping worked. It appears ALPUS produces several models
of GlidePoint. I hope the other models are OK too.
The check code can still be activated by defining the PSM_CHECKSYNC
option in the config file. (The bit checking slightly reduces, if not
completely eliminates, weird mouse behavior cased by unsynchronized
mouse data packets. It also helps us to detect if the mouse interrupt
can ever be lost. But, well, if there are devices which cannot be
supported this way...)
4. The `psm' driver does not include the protocol emulation code by
default. The code can still be compiled in if the PSM_EMULATION option
is specified in the config file. Louis Mamakos suggests the emulation
code is putting too much in the kernel, and `moused' works well.
I will think about this later and decide if the entire emulation
code should be removed.
5. And, of course, the fix in `scprobe()' from Bruce to cure the
UserConfig problem. My code in `kbdio.c' is slightly different from
his patch, but has the same effect. There still is a possibility that
`scprobe()' gets confused, if, for whatever reasons, the user holds
down a key for very long time during the boot process. But we cannot
cope with everything, can we?
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
Most of the standard utilities that depended on (or were broken in
a different way by) the old behaviour of interpreting "" as "."
were fixed a year or two ago. There is still a fairly harmless
bug in tar and a harmless bug in gzip. Tar apparently replaces
"/" by "" when it strips leading slashes.
decrease the size of buffer_map to approx 2/3 of what it used to be
(buffer_map can be smaller now.) The original commit of these changes
increased the size of buffer_map to the point where the system would
not boot on large systems -- now large systems with large caches will
have even less problems than before.
the sd & od drivers. There is also slight changes to fdisk & newfs
in order to comply with different sectorsizes.
Currently sectors of size 512, 1024 & 2048 are supported, the only
restriction beeing in fdisk, which hunts for the sectorsize of
the device.
This is based on patches to od.c and the other system files by
John Gumb & Barry Scott, minor changes and the sd.c patches by
me.
There also exist some patches for the msdos filesys code, but I
havn't been able to test those (yet).
John Gumb (john@talisker.demon.co.uk)
Barry Scott (barry@scottb.demon.co.uk)
a) Removal of private typedefs tulip_uint*_t, use standard u_int_*_t.
b) Change [Dd][Cc]21.4. to just 21.4., seems Dec has done this to all
of the drivers for all OS's. (Did they get in trouble with someone?)
[The few that remain can either not be eliminated, or are waiting for
additional driver functional changes that will remove them.]
c) Move some code from dc21040.h into the driver, later a whole block of that
code and more will move to devar.h, but for now this makes it easier
to study diffs.
d) Add a big bold comment to the README.de file about it not reflecting
reality anymore.
Note that these are all cosmetic changes and should be no functional
change in the driver whatsoever. If _anyone_ spots a problem introduced
by this please let me know ASAP!
scheme. Additionally, add the capability for checking for unexpected
kernel page faults. The maximum amount of kva space for buffers hasn't
been decreased from where it is, but it will now be possible to do so.
This scheme manages the kva space similar to the buffers themselves. If
there isn't enough kva space because of usage or fragementation, buffers
will be reclaimed until a buffer allocation is successful. This scheme
should be very resistant to fragmentation problems until/if the LFS code
is fixed and uses the bogus buffer locking scheme -- but a 'fixed' LFS
is not likely to use such a scheme.
Now there should be NO problem allocating buffers up to MAXPHYS.
are always together with Framing Errors and they were incorrectly
treated as FE's and discarded.
Reorganized the BREAK/FE/PE tests.
Found by: NIST-PCTS
with sio devices (not perfectly, since there is no way to flush the tx
holding register on 8250-16450's. I'm not sure if resetting the fifos
flushes the tx shift register).
Reminded by: NIST-PCTS
is completely empty. There is no interrupt for output completion, so
poll for it every 10 ms after output is nearly complete. Now ttywait()
works right.
Reminded by: NIST-PCTS
succeeds. Writing an action now succeeds iff the handler isn't changed.
(POSIX allows attempts to change the handler to be ignored or cause an
error. Changing other parts of the action is allowed (except attempts
to mask unmaskable signals are silently ignored as usual).)
Found by: NIST-PCTS
registers.) Also clean up some namespace pollution, and remove
gcc-1 support (nothing really works with it anymore anyway.)
Submitted by: Bruce Evans <bde@freebsd.org> and me.
the queues and generate a SIGINT. Previously, this wasn't done if ISIG
was clear or the VINTR character was disabled, and it was done by
converting the BREAK to a VINTR character and sometimes bogusly echoing
this character.
Found by: NIST-PCTS
consistent stack frame in fastmove() so that only one new fault handler
is necessary.
Should be in 2.2. Harmless until the i586 versions are reenabled.
Per Wayne Scott of Intel, the old sequence took 20cycles!!! on a P6.
Another nice side-benefit is that the kernel is about 3K smaller!!!
Submitted by: Wayne Scott <wscott@ichips.intel.com>
larger than the vfs layer can provide. We now automatically support
32K clusters if MSDOSFS is installed, and panic if a filesystem tries
to allocate a buffer larger than MAXBSIZE.
This commit is a result of some "prodding" by BDE.
larger than the vfs layer can provide. We now automatically support
32K clusters if MSDOSFS is installed, and panic if a filesystem tries
to allocate a buffer larger than MAXBSIZE.
This commit is a result of some "prodding" by BDE.
The rest of the code was treating it as a header mbuf, but it was
allocated as a normal mbuf.
This fixes the panic: ip_output no HDR when you have a multicast
tunnel configured.
the keyboard IO port definitions from <machine/console.h>.
Note: I do not have a machine available to test this yet, I sent this
for review to several people who have not replied.
This is also totally busted in 2.2, which has half of the syscons/psm/kbdio
changes in it. This really desperately needs to be tested and fixed
in 2.2 as well.
SCBs in response to a busfree.
When re-queueing an SCB that returned with QUEUE FULL status, reset its timeout.
Ensure that aborted SCBs have an error code set in there xs before it gets
passed back up with scsi_done.
Fix a few KNF nits.
Immediate SCBs, since they always send messages that tell the target to
transition to bus free now rely on the busfree interrupt instead of the
IMMEDDONE sequencer interrupt that was generated before.
Rearrange some code in the message out loop to give ATN a little more time
to drop before we ACK the last byte.
Use SPIORDY instead of REQINIT when snooping for a tag message on a reconnect.
This is done for the same reasons we use SPIORDY in the inb functions.
When going into BITBUCKET mode, turn off HDMAEN in the DFCNTRL register so
that we can "not care" what the value of HCNT is. If HCNT is 0, BITBUCKET
mode won't transfer any data if HDMAEN is set. Seeing as we don't want the
transfer to even think about touching the host, this seems more sane anyway.
Thanks to "Dan Willis" <dan@plutotech.com> for pointing out that this was
a problem.
uses /usr/include/sys/*, which may point to a different build tree. I'm
not sure that this is necessary, but there was a question mark over what
/usr/include/sys points to when building the "user mode" binaries in the
kernel code, especially when building the smp tree.
I suspect that the "right" line here is to use ${INCLUDES}, but that
causes warnings about unused static inline functions in stdio.h and ctype.h
also fixes a bug I've been chasing for a LONG TIME,
due to the fact that spec_bwrite is a NOP and I didn't realise it..
old symptom:
mount -t devfs devfs /mnt
mount /mnt/wd0e /mnt/mnt2
umount /mnt2 <process hangs>
there are some pretty large structural differences internal to devfs
but outwards it should look the same.
I have not yet tested extensively but will do so and fix 3 warnings tomorrow.
SPIORDY should go active on any REQ of the bus, so testing for REQINIT is
not necessary. It also seems that testing for SPIORDY is more robust then
REQINIT since SPIORDY comes active after REQINIT and PHASEMIS seems to take
some time to come true after REQ is asserted if the phase has changed. Of
course, none of this is documented.
This should give the code savings of my original changes, without breaking the
driver on fast peripherals.
The 'getchar' function in syscons (sccngetc) is used by UserConfig to
get keyboard input from the user. When it was modified to use the
shared keyboard port routines it used the port passed in during the
probe routine. Since the probe routine was not yet called, the port was
set to 0, which is obviously not going to work.
Pre-initialize sc_port to IO_KBD which is really a kludge, but it's how
the previous driver did it's job.
Found by: remote GDB
substantially increasing buffer space. Specifically, we double
the number of buffers, but allocate only half the amount of memory
per buffer. Note that VDIR files aren't cached unless instantiated
in a buffer. This will significantly improve caching.
do reset it from the QOUTCNT register inside a pause/unpause. This now happens
once per command complete interrupt in the paging case (one interrupt can be
for multiple completed commands). I may introduce a counter and do a lazy
update in the future, similar to what is done with the QINCNT.
Enhance the QUEUE FULL condition handling so that the number of openings will
be reduced. This has become more important now that the driver is faster.
This code really belongs in the gerneric SCSI layer, as will be the case once
3.0 gets the code from the 'SCSI' branch.
Add some #if 0'd out trace code I've been using to help debug sequencer
problems.
Fix the SCB paging problem that I was seeing. This was only on my 7850
controller and stems from the fact that its QINFIFO can only handle 3bit
SCB identifiers. This means that you can only have 8 transactions open at
a time with the current paging scheme to these controllers. The code added
to enforce this is generic in that it tests for the number of relevent bits
that the QINFIFO can store and adjusts the max accordingly. It may be possible
to come up with a scheme that allows for more than 8 commands at a time, but
I don't know that it is worth the effort simply to fix a low end card. The
aic7880 still can do 255.
This problem may be related to what Andrey was seeing since I don't have n
aic7770 rev E chip here to test on, but as soon as someone probes one of these
cards with this new code, the dmesg output will tell the whole story.
aic7xxx cards failing on certain motherboards, reverse the logic used to
control this feature. AHC_FORCE_PIO is replaced with AHC_ALLOW_MEMIO.
GENERIC no longer needs to specify the AHC_FORCE_PIO option since this is
the default.
initial selection when entering the status phase. This is the same assertion
we use for all the other data transfer phases.
Hopefully fix the hangs in the mesgin and mesgout phases that I introduced
last week during some code cleanup. I need to get some of these 12MB/s
drives so I can reproduce these hangs here...
Add a pause disable in the SCB paging case around our manipulation of the
QOUTQCNT variable. This is simply extra sanity.
Set LASTPHASE to P_BUSFREE once we see a busfree so that the kernel driver can
differentiate this from a data out phase.
user supplies a bad address, because they push a lot of stuff that the
fault handler doesn't know about onto the stack. This has been broken
for more than half a year despite being tested for almost half a year
in -current.
duplicate ip address 204.162.228.7! sent from ethernet address: 08:00:20:09:7b:1d
changed to
arp: 08:00:20:09:7b:1d is using my IP address 204.162.228.7!
and
arp info overwritten for 204.162.228.2 by 08:00:20:09:7b:1d
changed to
arp: 204.162.228.2 moved from 08:00:20:07:b6:a0 to 08:00:20:09:7b:1d
I think the new wordings are more clear and could save some support
questions.
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
with the copyright stuff fixed so soon (this should be merged into 2.2 when
you have a chance, Poul).
This is the new AWE32 driver, with support for the AWE32's fancy MIDI
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
the other two trees. Bump RELDATE to Feb 1997, one greater than 2.2.
Now I can go update my porting.sgml.
NOT a 2.2 candidate, in case phk's wondering. :)
routines. An older version of this was tested successfully on all of my
systems with PS/2 mice. This was brought in without testing because it
is necessary due to the previously committed syscons changes.
Submitted by: Kazutaka Yokota <yokota@zodiac.mech.utsunomiya-u.ac.jp>
syscons and psm, curtesy Kazutaka Yokota with minor changes by
me. This contains an update of the psm driver as well.
This also fixes the breakage that I introduced to the psm driver by
making syscons poll for keyboard events in the atempt to fix the
hanging keyboard problem.
It works perfectly for me, and I'd like to hear from all that
have had keyboard/ps/2 mouse problems if this is the cure...
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
wdreg.h: Delete wd_ctlr macro. PC98 version of wd.c treats it as a
variable.
GENERIC98: Delete ep0 entry. Current ep driver write I/O port 0x100.
This clobbers ICW of i8259, because upper 8bits of address line is not
masked on mother board.
if_fe.c: Merge from revision 1.18 of sys/i386/isa/if_fe.c.
pc98.c: Globalize dmapageport, because SCSI driver use this
variable.
wd82371.c: Yet another merge.
These are 2.2 candidates.
Submitted by: The FreeBSD(98) Development Team
almost complete control over RTS (control of its initial value is still
missing).
This fixes PR 1644 for sio.
The author of PR 1644 wants it in 2.1.6 and 2.2. This may be safe since
the complications are only in rarely used cases that I hope I've covered.
sys/pc98/i386/machdep.c: sync with i386/i386/machdep.c
sys/pc98/conf/options.pc98: sync with i386/conf/options.i386
sys/i386/isa/sound: DMA auto initialize mode support for PC98.
contributed by: Akio Morita <amorita@bird.scphys.kyoto-u.ac.jp>
Definite 2.2 material, I believe.
Submitted by: The FreeBSD (98) Development Team
We encountered an interesting situation where the superblock for
a file system got written to disk with the "fs_fmod" flag set to
one. It appears that this flag is normally supposed to be cleared
during ffs_sync(), but we experienced a crash, or some other weird
occurrence that left it on the disk set to 1.
Later this partition was mounted read-only... and the fs_fmod
field was never cleared, causing ffs_sync() to panic "rofs mod"
when trying to unmount that filesystem (ffs_vfsops.c: line 790).
fix:
set this bit to 0 when you load the superblock from disk.
(see more complete mail on this to hackers)
bridges with support for 64 bit memory addresses and 32 bit I/O addresses).
The code is not complete. It ignores the upper half of the long addresses.
This is not a problem on PC compatible systems, but has to be fixed for
real computers.
one too small for (hex) 12345678 and 4 too small for -1234567890. Large
values can be created by config and userconfig although not (previously)
by visual userconfig.
Fixed a sign extension bug for backspacing on "negative" hex values in
editval().
Increased field width and range for `flags' so that all possible values
can be displayed and edited.
