ntpd is hard-coded to use /dev/ppsN, and typically when multiple PPS sources
are available the sysadmin will symlink the right one(s) to /dev/ppsN, so
it's best to not usurp those names directly.
both the post-filter and post-thread callbacks.
Also eliminate a completely unecessary write to INTC_ISR_CLEAR register,
which clears a software-generated interrupt that can only happen with a
write to INTC_ISR_SET (which nothing does).
The DISP DPLL clock is slower and was making the PRU programs slower
on FreeBSD than on Linux.
Submitted by: Manuel Stuehn <freebsdnewbie at freenet.de>
MFC after: 1 week
Minimum LCDC is 2 so clock freq shouild be 2*max_pixel_clock. Maximum pixel
clock for HDMI is 148500 (1920x1080). But AM335x can not run in this mode
due to bandwidth and clock limitations
1 second is not enugh for TDA19988 HDMI framer (e.g. on Beaglebone Black)
- Add per-device i2c_timout sysctl (dev.iichb.X.i2c_timeout) to control
I2C bus timeout manually
- Pass softc instead of device_t to all sysctl handlers
While in theory this should have been a transparent change (and was for all
other drivers), cpsw(4) never used the proper accessor macros in a few
places but spelt the indirect m_hdr.mh_* out itself. Convert those to
use m_len and m_data and unbreak the driver build.
To cut off the power we need to start the shutdown sequence by writing
the OFF bit on PMIC.
Once the PMIC is programmed the SoC needs to toggle the PMIC_PWR_ENABLE
pin when it is ready for the PMIC to cut off the power. This is done by
triggering the ALARM2 interrupt on SoC RTC.
The RTC driver only works in power management mode which means it won't
provide any kind of time keeping functionality. It only implements a way
to trigger the ALARM2 interrupt when requested.
Differential Revision: https://reviews.freebsd.org/D1489
Reviewed by: rpaulo
MFC after: 2 weeks
According to http://e2e.ti.com/support/arm/sitara_arm/f/791/t/210729 the
USB reset pulse has an undocumented duration of 200ns and during this
period the module must not be acessed.
We wait for 100us to take into account for some imprecision of the early
DELAY() loop.
This fixes the eventual 'External Non-Linefetch Abort (S)' that happens at
boot while resetting the musb subsystem.
While here, enable the USB subsystem clock before the first access.
Discussed with: ian, adrian
MFC after: 2 weeks
This enables the use of GPIO pins as interrupt sources for kernel devices
directly attached to gpiobus (userland notification will be added soon).
The use of gpio interrupts for other kernel devices will be possible when
intrng is complete.
All GPIO pins can be set to trigger on:
- active-low;
- active-high;
- rising edge;
- falling edge.
Tested on: Beaglebone-black
Fix the following issues:
- Removed revision from device softc, it isn't used anywhere else out of
device attach routine;
- Move the duplicated code for verification of valid banks (and pins) to
a single function;
- Use some macros to simplify the handling of some constants;
- Update some stale comments.
TI OMAP controllers which will return the reset-in-progress bit as zero if
you read the status register too fast after setting the reset bit.
The zero is apparently from a stale snapshot of the internal state presented
in the interface register, and leads to a false indication that the reset
is complete when it either hasn't started yet or is in-progress. The
workaround is to first loop until the bit is seen as asserted, then do the
normal loop waiting to see it de-asserted.
Submitted by: Michal Meloun <meloun@miracle.cz>
