it as being in range.
set ifaddr 1.2.3.4/0 5.6.7.8/0
no longer allows 0.0.0.0 as a valid IP.
Reported/tested by: Bohdan Horst <nexus@hoth.amu.edu.pl>
MFC after: 3 days
of 1024- Ultra4 256). Rename 'requests' tag to 'request_pool' for clarity.
Make sure we do correct xpt_freeze_simq/CAM_RELEASE_SIMQ if we run out
of chip resources.
MFC after: 6 days
o Include <sys/select.h> from <sys/types.h> in the __BSD_VISIBLE case,
so applications and base software can be slowly updated.
o Prototype select() in <sys/select.h>. It was previously only
prototyped in <unistd.h>.
o Add some XXX's to <sys/types.h>.
Reviewed by: -standards
- nexus no longer has PCI bridges as direct children, so the PCI bus
ivar is no longer used and is removed.
- Don't attach default EISA, ISA, or MCA busses. Instead, if we do not
have an acpi0 device after bus_generic_probe(), add a legacy0 child
device.
- Remove machine/nexusvar.h.
ACPI or for when ACPI support is disabled or not present in the kernel.
Basically, the nexus device is now split into two with some parts
(such as adding default ISA, MCA, and EISA busses if they aren't found
as well as support for PCI bus device ivars) being moved to the legacy
driver.
to use DOC_LANG to specify which languages the doc/ is built for.
Note: be aware that the DOC_LANG setting in /etc/make.conf will now
take the effect on "make release". (This is probably the desired
behavior anyway.)
PR: docs/42924
that already exists for hosts: being able to specify a section that applies
to every program *except* the one in question.
The normal syntax for program specification is still valid. For the new
capability, one uses:
!-program
Since there is no way to specify a program beginning with a dash in the old
syntax, as it would be interpreted as the case above, the following
alternative syntax to the original capability is provided:
!+program
This shouldn't introduce incompatibilities with any syslogd configuration
in production because -stable's syslogd does not support a dash anywhere in
the program specification.
MFC after: 2 weeks
o Move len initialization closer to place of its first usage.
o Compare len with 0 to improve readability.
o Explicitly zero out phlen in ip_insertoptions() in failure case.
Suggested by: jhb
Reviewed by: jhb
MFC after: 2 weeks
variable natively. It should allow you to use any sysctl mib set, but due
to limitations of what I can do with macros, right now it's limited to two,
which is all this program used anyway.
Sponsored by: Bright Path Solutions
themselves cause a failure if it is told to use a __widget that there is
no implementation for them. missing an implementation for __unused etc is
harmless. But not having a __packed implementation when the kernel code
really needs it is a big deal.
static void const * const __set_##set##_sym_##sym
__attribute__((__section__("set_" #set),__unused__)) = &sym
becomes:
static void const * const __set_##set##_sym_##sym
__section("set_" #set) __unused = &sym
Like the other macros, these #define away for unrecognized compilers or
lint.
Also, fix the argments in the previous commit for the non-gcc case. lint
might be a bit happier about that. Note that the gcc <= 2.6 case
needs some research.
expand to __attribute__((packed)) and __attribute__((aligned(x)))
respectively. Replace the handful of gcc-ism's that use
__attribute__((aligned(16))) etc around the kernel with __aligned(16).
There are over 400 __attribute__((packed)) to deal with, that can come
later. I just want to use __packed in new code rather than add more
gcc-ism's.
In mpttimeout, call mpt_intr just on the offchance that we missed
an interrupt. We can check to see whether or not the command that
is timing out got completed.
When we *do* decide to timeout a command, set the command state to
REQ_TIMEOUT and then invoke another timeout (hz/10)- mpttimeout2.
This allows us to catch a couple cases we've seen where the command
we timed out on in fact is ready to be completed by the firmware.
In any case, it's only after mpttimeout2 is called that we actually
take down the private state and free the request itself. CAM has
been notified in mpttimeout anyway. This whole area should be redone,
but that will take 105% of my available game time for this month.
Fix a couple of missing (and not useful, at presnet) CAMLOCK_2_MPTLOCK
and MPTLOCK_2_CAMLOCK locations.
Split mpt_notify into mpt_ctlop, which handles all reply completions
that have 0x800000000 or'd into the ContextID. This function can, in
fact, call mpt_event_notify_reply, which handles the traditional
async event notifications. While we're at it, put in the extremely
important (but currently untested) code that send back an Ack to
an Event Notification (if the Event Notification is marked with
AckRequired). Note that an Ack also generates another ctlop completion,
tra la.
Fix up mpt_done substantially to try and get how we plug into CAM
correctly done. Remove bogus CAM_RELEASE_SIMQ settings.
Do some cleanups in mpt_action that are related to speed negotiation
for Ultra4 cards. This is an area that is still quite fragile and
worrisome as config data being read back often doesn't make sense or
jibe with the documentation.
At any rate, after these changes were done, I was finally able to
get Lars Eggert's dual 320M disk system to stay up under load all
weekend- hopefully we're in good enough for now shape.
MFC after: 1 week
Define the CFG_DAGA_OFF offset as 128 bytes instead of 40- gives us
a more reasonable headroom.
When reading a config page, zero out the entire request area- not just
the length of the request. This is because we cleverly (cheezily) return
configuration data back into the allocated request area, so it's nice
to make sure we start with a clean area to write on.
MFC after: 1 week
Instead, based upon whether ISP_DAC_SUPPORTED is defined, typedef
isp_dma_addr_t appropriately.
If ISP_DAC_SUPPORTRED is defined, the DMA_WD2/DMA_WD3 macros do something
useful, else they define to '0'.
