This eliminates a lot of #ifdef SMP type code. Things like _curproc reside
in a data page that is unique on each cpu, eliminating the expensive macros
like: #define curproc (SMPcurproc[cpunumber()])
There are some unresolved bootstrap and address space sharing issues at
present, but Steve is waiting on this for other work. There is still some
strictly temporary code present that isn't exactly pretty.
This is part of a larger change that has run into some bumps, this part is
standalone so it should be safe. The temporary code goes away when the
full idle cpu support is finished.
Reviewed by: fsmp, dyson
top of the hardware interrupt handlers. Apparently this is slightly
faster with the bit scanning instruction that looks these up - this set of
changes reverts the original change.
Reviewed by: bde
- vector.s <- stub called by i386/exception.s
- icu_vector.s <- UP
- apic_vector.s <- SMP
Split icu.s into UP and SMP specific files:
- ipl.s <- stub called by i386/exception.s (formerly icu.s)
- icu_ipl.s <- UP
- apic_ipl.s <- SMP
This was done in preparation for massive changes to the SMP INTerrupt
mechanisms. More fine tuning, such as merging ipl.s into exception.s,
may be appropriate.
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After the ISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
- doesn't break my system.
- NOT yet verified on the affected motherboard.
Stifle an annoying dma_start busy message for the sound cards.
Submitted by: "John S. Dyson" <toor@dyson.iquest.net>
simplifies some assumptions and stops some code compile problems.
This should fix the compile hiccup in PR#3491, but smp kernel profiling
isn't likely to be fixed by this.
Peter Wemm <peter@spinner.DIALix.COM>, Steve Passe <smp@csn.net>
removed all the IPI_INTS code.
made the XFAST_IPI32 code default, renaming Xfastipi32 to Xinvltlb.
cleanup of i386/isa/isa_device.h to eliminate SMP dependancies:
made the id_irq member of struct isa_device an u_int.
made the id_drq member of struct isa_device an int.
removed all other '#ifdefs' concerning SMP & APIC_IO.
removed SMP/APIC_IO dependancies from if_ze.c.
There are various options documented in i386/conf/LINT, there is more to
come over the next few days.
The kernel should run pretty much "as before" without the options to
activate SMP mode.
There are a handful of known "loose ends" that need to be fixed, but
have been put off since the SMP kernel is in a moderately good condition
at the moment.
This commit is the result of the tinkering and testing over the last 14
months by many people. A special thanks to Steve Passe for implementing
the APIC code!
have successfully built, booted, and run a number of different ELF
kernel configurations, including GENERIC. LINT also builds and
links cleanly, though I have not tried to boot it.
The impact on developers is virtually nil, except for two things.
All linker sets that might possibly be present in the kernel must be
listed in "sys/i386/i386/setdefs.h". And all C symbols that are
also referenced from assembly language code must be listed in
"sys/i386/include/asnames.h". It so happens that failure to do
these things will have no impact on the a.out kernel. But it will
break the build of the ELF kernel.
The ELF bootloader works, but it is not ready to commit quite yet.
print "at <not configured>" for iobase == -1 (autodetect not happens)
and not print anything for iobase == -2 (none)
Old code treat this two special config numbers as big port numbers.
I have code to calibrate the overhead fairly accurately, but there
is little point in using it since it is most accurate on machines
where an estimate of 0 works well. On slow machines, the accuracy
of DELAY() has a large variance since it is limited by the resolution
of getit() even if the initial delay is calibrated perfectly.
Use fixed point and long longs to speed up scaling in DELAY().
The old method slowed down a lot when the frequency became variable.
Assume the default frequency for short delays so that the fixed
point calculation can be exact.
Fast scaling is only important for small delays. Scaling is done
after looking at the counter and outside the loop, so it doesn't
decrease accuracy or resolution provided it completes before the
delay is up. The comment in the code is still confused about this.
called early for console i/o. The timer is usually in BIOS mode
if it isn't explicitly initialized. Then it counts twice as fast
and has a max count of 65535 instead of 11932. The larger count
tended to cause infinite loops for delays of > 20 us. Such delays
are rare. For syscons and kbdio, DELAY() is only called early
enough to matter for ddb input after booting with -d, and the delay
is too small to matter (and too small to be correct) except in the
PC98 case. For pcvt, DELAY() is not used for small delays (pcvt
uses its own broken routine instead of the standard broken one),
but some versions call DELAY() with a large arg when they unnecessarily
initialize the keyboard for doing console output. The problem is
more serious for pcvt because there is always some early console
output.
Guard against the i8254 timer being partially or incorrectly
initialized. This would have prevented the endless loop.
Should be in 2.2.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
is still broken - it doesn't restore the floating point state.
2.2-BETA users should disable it using npx0 flags 0x04 the same as
2.2-ALPHA users should have.
user supplies a bad address, because they push a lot of stuff that the
fault handler doesn't know about onto the stack. This has been broken
for more than half a year despite being tested for almost half a year
in -current.
negative-logic flags (flags 0x01 and 0x02 for npx0, defaulting to unset = on).
This changes the default from off to on. The options have been in current
for several months with no problems reported.
Added a boot-time negative-logic flag for the old I5886_FAST_BCOPY option
which went away too soon (flag 0x04 for npx0, defaulting to unset = on).
Added a boot-time way to set the memory size (iosiz in config, iosize in
userconfig for npx0).
LINT:
Removed old options. Documented npx0's flags and iosiz.
options.i386:
Removed old options.
identcpu.c:
Don't set the function pointers here. Setting them has to be delayed
until after userconfig has had a chance to disable them and until after
a good npx0 has been detected.
machdep.c:
Use npx0's iosize instead of MAXMEM if it is nonzero.
support.s:
Added vectors and glue code for copyin() and copyout().
Fixed ifdefs for i586_bzero().
Added ifdefs for i586_bcopy().
npx.c:
Set the function pointers here.
Clear hw_float when an npx exists but is too broken to use.
Restored style from a year or three ago in npxattach().
handlers if interrupts are nested more than a few (3) deep. This
only reduces the maximum nesting level by 1 with the standard
drivers unless there is a related bug somewhere, but can't hurt
much (the worst case is returning to hoggish interrupt handler like
wdintr(), but such interrupt handlers hurt anyway).
Fixed a previously harmless race incrementing the interrupt nesting
level.
This should be in 2.1.6 and 2.2.
hardware interrupt counts add up to the total. Previously, software
interrupts generated by splz() were counted in the total. These
software interrupts seem to be very rare - there have apparently been
0 of them on freefall among the last 352448857 interrupts.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
make it more intelligible, improve the partially bogus locking, and
allow for a ``quick re-acquiration'' from a pending release of timer 0
that happened ``recently'', so it was not processed yet by clkintr().
This latter modification now finally allows to play XBoing over
pcaudio without losing sounds or getting complaints. ;-) (XBoing
opens/writes/closes the sound device all over the day.)
Correct locking for sysbeep().
Extensively (:-) reviewed by: bde
Testing with the high frequency of 20000 Hz (to find problems) only found
the problem that this frequency is too high for slow i386's.
Disable interrupts while setting the timer frequency. This was unnecessary
before rev.1.57 and forgotten in rev.1.57. The critical (i8254) interrupts
are disabled in another way at boot time but not in the sysctl to change
the frequency.
enable flag instead of enable_intr() to restore it to its usual state.
getit() is only called from DELAY() so there is no point in optimising
its speed (this wasn't so clear when it was extern), and using
enable_intr() made it inconvenient to call DELAY() from probes that need
to run with interrupts disabled.
All new code is "#ifdef PC98"ed so this should make no difference to
PC/AT (and its clones) users.
Ok'd by: core
Submitted by: FreeBSD(98) development team
ansi and traditional cpp.
The nesting rules of macros are different, which required some changes.
Use __CONCAT(x,y) instead of /**/.
Redo some comments to use /* */ rather than "# comment" because the ansi
cpp cares about those, and also cares about quote matching.
time. The results are currently ignored unless certain temporary options
are used.
Added sysctls to support reading and writing the clock frequency variables
(not the frequencies themselves). Writing is supposed to atomically
adjust all related variables.
machdep.c:
Fixed spelling of a function name in a comment so that I can log this
message which should have been with the previous commit.
Initialize `cpu_class' earlier so that it can be used in startrtclock()
instead of in calibrate_cyclecounter() (which no longer exists).
Removed range checking of `cpu'. It is always initialized to CPU_XXX
so it is less likely to be out of bounds than most variables.
clock.h:
Removed I586_CYCLECTR(). Use rdtsc() instead.
clock.c:
TIMER_FREQ is now a variable timer_freq that defaults to the old value of
TIMER_FREQ. #define'ing TIMER_FREQ should still work and may be the best
way of setting the frequency.
Calibration involves counting cycles while watching the RTC for one second.
This gives values correct to within (a few ppm) + (the innaccuracy of the
RTC) on my systems.
regarding apm to LINT
- Disabled the statistics clock on machines which have an APM BIOS and
have the options "APM_BROKEN_STATCLOCK" enabled (which is default
in GENERIC now)
- move around some of the code in clock.c dealing with the rtc to make
it more obvios the effects of disabling the statistics clock
Reviewed by: bde
channel at the same time. The functions isa_dma_acquire() and
isa_dma_release() should be used in all ISA drivers which call isa_dmastart().
This can be used more generally to register the usage of DMA channels in
any driver, but it is required for drivers using isa_dmastart() and friends.
Clean up sanity checks, error messages, etc.
Remove isa_dmadone_nobounce(), it is no longer needed
Reviewed by: bde
Always delay using one inb(0x84) after each i/o in rtcin() - don't
do this conditional on the bogus option DUMMY_NOPS not being defined.
If you want an optionally slightly faster rtcin() again, then inline
it and use a better named option or sysctl variable. It only needs
to be fast in rtcintr().
clock interrupts.
Keep a 1-in-16 smoothed average of the length of each tick. If the
CPU speed is correctly diagnosed, this should give experienced users
enough information to figure out a more suitable value for `tick'.
fd and wt drivers need bounce buffers, so this normally saves 32K-1K
of kernel memory.
Keep track of which DMA channels are busy. isa_dmadone() must now be
called when DMA has finished or been aborted.
Panic for unallocated and too-small (required) bounce buffers.
fd.c:
There will be new warnings about isa_dmadone() not being called after
DMA has been aborted.
sound/dmabuf.c:
isa_dmadone() needs more parameters than are available, so temporarily
use a new interface isa_dmadone_nobounce() to avoid having to worry
about panics for fake parameters. Untested.
variants, idea taken from NetBSD clock.c.
At least year calculation was wrong, pointed by Bruce.
Use different strategy to store year for BIOS without RTC_CENTURY
was overlapping with another file, and making some undesirable behavior a
little worse - it's triggering a bug in config that appears to have been
there for some time (before the options files, anyway.)
