apparently be confused by short TCP segments that have been manually
padded to the minimum ethernet frame size. The driver does short frame
padding in software as a workaround for a bug in the 8169 PCI devices
that causes short IP fragments to be corrupted due to an apparent
conflict between the hardware autopadding and hardware IP checksumming.
To fix this, we avoid software padding for short TCP segments, since
the hardware seems to autopad and checksum these correctly (even the
older 8169 NICs get these right). Short UDP packets appear to be
handled correctly in all cases. This should work around the IP header
checksum bug in the 8169 while not tripping the TCP checksum bug in
the 8111B/8168B and 8101E.
addresses shall access invalid descriptor DMA addresses on PCIe
hardwares and then panicked the system.
To fix it set descriptor DMA addresses before enabling Tx and Rx
such that hardware can see valid descriptor DMA addresses. Also
set RL_EARLY_TX_THRESH before starting Tx and Rx.
Reported by: steve.tell AT crashmail DOT de
Tested by: steve.tell AT crashmail DOT de
Obtained from: NetBSD
MFC after: 1 week
- First off, device drivers really do need to know if they are allocating
MSI or MSI-X messages. MSI requires allocating powerof2() messages for
example where MSI-X does not. To address this, split out the MSI-X
support from pci_msi_count() and pci_alloc_msi() into new driver-visible
functions pci_msix_count() and pci_alloc_msix(). As a result,
pci_msi_count() now just returns a count of the max supported MSI
messages for the device, and pci_alloc_msi() only tries to allocate MSI
messages. To get a count of the max supported MSI-X messages, use
pci_msix_count(). To allocate MSI-X messages, use pci_alloc_msix().
pci_release_msi() still handles both MSI and MSI-X messages, however.
As a result of this change, drivers using the existing API will only
use MSI messages and will no longer try to use MSI-X messages.
- Because MSI-X allows for each message to have its own data and address
values (and thus does not require all of the messages to have their
MD vectors allocated as a group), some devices allow for "sparse" use
of MSI-X message slots. For example, if a device supports 8 messages
but the OS is only able to allocate 2 messages, the device may make the
best use of 2 IRQs if it enables the messages at slots 1 and 4 rather
than default of using the first N slots (or indicies) at 1 and 2. To
support this, add a new pci_remap_msix() function that a driver may call
after a successful pci_alloc_msix() (but before allocating any of the
SYS_RES_IRQ resources) to allow the allocated IRQ resources to be
assigned to different message indices. For example, from the earlier
example, after pci_alloc_msix() returned a value of 2, the driver would
call pci_remap_msix() passing in array of integers { 1, 4 } as the
new message indices to use. The rid's for the SYS_RES_IRQ resources
will always match the message indices. Thus, after the call to
pci_remap_msix() the driver would be able to access the first message
in slot 1 at SYS_RES_IRQ rid 1, and the second message at slot 4 at
SYS_RES_IRQ rid 4. Note that the message slots/indices are 1-based
rather than 0-based so that they will always correspond to the rid
values (SYS_RES_IRQ rid 0 is reserved for the legacy INTx interrupt).
To support this API, a new PCIB_REMAP_MSIX() method was added to the
pcib interface to change the message index for a single IRQ.
Tested by: scottl
sparc64 GENERIC and the sound device drivers known working on sparc64
to use bus_get_dma_tag() to obtain the parent DMA tag so we can get rid
of the sparc64_root_dma_tag kludge eventually. Except for ath(4), sk(4),
stge(4) and ti(4) these changes are runtime tested (unless I booted up
the wrong kernels again...).
These are shared-memory variants based on Am79C90-compatible chips
that apart from the missing DMA engine are similar to the 'ledma'
variant including using a (pseudo-)bus/device for the buffer that
the actual LANCE device hangs off from. The performance of these is
close to that of the 'ledma' one, like expected at a few times the
CPU load though.
unlike documented may not take effect without an initialization. So
don't invoke (*sc_mediachange) directly in lance_mediachange() but
go through lance_init_locked(). It's suboptimal to impose this for
all chips but given that besides the affected PCI bus front-end the
only other front-end which supports media selection is and likely
ever will be the 'ledma' front-end I see not enough reason to break
the in-driver API for this (though one could argue both ways here).
front of isp_init so we can read NVRAM even if we're role ISP_NONE.
Prepare for reintroduction of channels (for FC) for N-Port
Virtualization.
Fix a botch in handle assignment that caused us to nuke one device
when a new one arrives and end up with two devices with the same
identity in the virtual target mapping table.
ifmedia_init() invocation. IFM_IMASK makes only sense here when all of
the maxium of 32 PHYs on each one MII bus support disjoint sets of media,
which generally isn't the case (though it would be nice if we had a way
to let NIC drivers indicate that for the few card models where the PHY
configuration is known/fixed and IFM_IMASK actually makes sense).
- Add and use a miibus_print_child() for the bus_print_child method which
additionally prints the PHY number (which actually is the PHY address)
so one can figure out the media instance <-> PHY number mapping from the
PHY driver attach output. This is intented to be usefull in situations
where the addresses of the PHYs on the bus are known (f.e. of internal/
integrated PHYs) so one can feed the appropriate media instance number
to ifconfig(8) (with the upcoming change for ifconfig(8)).
This is more or less inspired by the NetBSD mii_print().
multiple PHYs. In case some PHYs currently driven by ukphy(4) exhibit
problems when isolating due to incomplete implementations or silicon bugs
we'll need to add specific drivers for these. Looking at NetBSD and
OpenBSD I don't expect problems here though (quite the contrary; we still
seem to set MIIF_NOISOLATE without good reason in a bunch of PHY drivers).
- Fix a style(9) whitespace nit.
capability rather than hardcoded offsets for a particular card. While
I'm here, expand the constants some.
- Change the ahd(4) driver to use pci_find_extcap() to locate the PCI-X
capability to keep up with the first change.
Reviewed by: scottl, gibbs (earlier version)
that can be used to check whether receive data is ready, i.e. whether
the subsequent call of uart_poll() should return a char, and unlike
uart_poll() doesn't actually receive data.
- Remove the device-specific implementations of uart_poll() and implement
uart_poll() in terms of uart_getc() and the newly added uart_rxready()
in order to minimize code duplication.
- In sunkbd(4) take advantage of uart_rxready() and use it to implement
the polled mode part of sunkbd_check() so we don't need to buffer a
potentially read char in the softc.
- Fix some mis-indentation in sunkbd_read_char().
Discussed with: marcel
the newly added DEV_EISA. This is done so that these back-ends can
be compiled on platforms not providing in{b,w,l}()/out{b,w,l}() and
friends (but may wish to use them together with bus front-ends other
than the EISA one).
total size of all input reports is < 6.
PR: usb/106435
Submitted by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
Approved by: emax (mentor)
MFC after: 3 days
The separate bus front-end was inherited from the OpenBSD creator(4),
which at that time had a mainbus(4) (for USI/II machines, which use
an UPA interconnection bus as the nexus) and an upa(4) (for USIII
machines, which use a subordinate/slave UPA bus hanging off from the
Fireplane/Safari interconnection bus) front-end. With FreeBSD and
newbus there is/will be no need to have two separate bus front-ends
for these busses, so we can easily coallapse the shared front-end
and the back-end into a single source file (note that the FreeBSD
creator_upa.c was misnomer anyway; based on what it actually attached
to that should have been creator_nexus.c), actually OpenBSD meanwhile
also has moved to a shared front-end and a single source file. Due
to the low-level console support creator.c also wasn't free from bus
related things before.
While at it, also split sys/sparc64/creator/creator.h into a
sys/dev/fb/creatorreg.h that only contains register macros and move
the structures to the top of sys/dev/fb/creator.c as suggested by
style(9) so creator(4) is no longer scattered over two directories.
- Use OF_decode_addr()/sparc64_fake_bustag() to obtain the bus tags and
handles for the low-level console support instead of hardcoding
support for AFB/FFB hanging off from nexus(4) only. This is part 2/4
of allowing creator(4) to work in USIII machines (which have a UPA
bus hanging off from the Fireplane/Safari bus reflected by the nexus),
which already makes it work as the low-level console there.
- Allocate resources in the bus attach routine regardless of whether
creator(4) is used as for the low-level console and thus the required
bus tags and handles have been already obtained or not so the resources
are marked as taken in the respective RMAN.
- For both obtaining the bus tags and handles for the low-level console
support as well as allocating the corresponding resources in the
regular bus attach routine don't bother to get all for the maximum of
24 register banks but only (for) the two tag/handle pairs required for
providing the video interface for syscons(4) support. If we can't
allocate the rest of them just limit the memory range accessible via
creator_fb_mmap() accordingly.
- Sanity check the memory range spanned by the first and last resources
and the resources in between as far as possible, as the XFree86/Xorg
sunffb(4) expects to be able to access the whole region, even though
the backing resources are actually non-continuous. Limit and check
the memory range accessible via creator_fb_mmap() accordingly.
- Reduce the size of buffers for OFW properties to what they actually
need to hold.
- Rename some tables to creator_<foo> for consistency.
- Also for the sizes in the creator_fb_mmap() mapping table entries use
macros for consistency, add macros for the remaining register banks
for completeness.
operation as it ran out of free descriptors or if there are too many
segments in the first place, call bus_dmamap_unload() in order to
unload the already loaded segments.
For trying to map the defragmented mbuf (chain) in re_encap() this
introduces re_dma_map_desc() setting arg.rl_maxsegs to 0 as a new
failure mode. Previously we just ignored this case, corrupting our
view of the TX ring.
o In re_txeof():
- Don't clear IFF_DRV_OACTIVE unless there are at least 4 free TX
descriptors. Further down the road re_encap() will bail if there
aren't at least 4 free TX descriptors, causing re_start() to
abort and prepend the dequeued mbuf again so it makes no sense
to pretend we could process mbufs again when in fact we won't.
While at it replace this magic 4 with a macro RL_TX_DESC_THLD
throughout this driver.
- Don't cancel the watchdog timeout as soon as there's at least one
free TX descriptor but instead only if all descriptors have been
handled. It's perfectly normal, especially in the DEVICE_POLLING
case, that re_txeof() is called when only a part of the enqueued
TX descriptors have been handled, causing the watchdog to be
disarmed prematurely.
o In re_encap():
- If m_defrag() fails just drop the packet like other NIC drivers
do. This should only happen when there's a mbuf shortage, in which
case it was possible to end up with an IFQ full of packets which
couldn't be processed as they couldn't be defragmented as they
were taking up all the mbufs themselves. This includes adjusting
re_start() to not trying to prepend the mbuf (chain) if re_encap()
has freed it.
- Remove dupe initialization of members of struct rl_dmaload_arg to
values that didn't change since trying to process the fragmented
mbuf chain.
While at it remove an unused member from struct rl_dmaload_arg.
o In re_start() remove a abandoned, banal comment. The corresponding
code was moved to re_attach() some time ago.
With these changes re(4) now survives one day (until stopped) of
hammering out packets here.
Reviewed by: yongari
MFC after: 2 weeks
- Retire the PCI_SUB*_1 constants and don't try to read a subvendor ID out
of them. There isn't a standard subvendor ID field for PCI-PCI bridges.
Instead, the dword at offset 0x34 is actually mostly reserved except for
the LSB which is the capabilities pointer.
- Add support for the PCI-PCI bridge subvendor ID capability (13) and use
it to set the subvendor ID for PCI-PCI bridges.
MFC after: 1 month
functions. The idea is taken from OpenBSD.
- Set/clear jumbo frame configurations for bge(4).
- Re-add BCM5750 PHY workaround for bce(4), which was mistakenly removed
from the previous commit.
- Move some PHY bug detections from brgphy.c to if_bge.c.
- Do not penalize working PHYs.
- Re-arrange bge_flags roughly by their categories.
- Fix minor style(9) nits.
PR: kern/107257
Obtained from: OpenBSD
Tested by: Mike Hibler <mike at flux dot utah dot edu>
o eliminate assumptions that half/quarter rate channels on exist in 11a
o handle frequency mapping between hal and net80211; hal gives us freq's
in the range 2422..2437 that we remap
MFC after: 1 month
bridge if it doesn't pass MSI messages up correctly. We set the flag
in pcib_attach() if the device ID is disabled via a PCI quirk.
- Disable MSI for devices behind the AMD 8131 HT-PCIX bridge. Linux has
the same quirk.
Tested by: no one despite repeated calls for testers
laptops.
Tested by: [1] Lion G. <liontanker@hotmail.com>
[2] Pietro Cerutti <pietro.cerutti@gmail.com>
Specialized mixer initialization for STAC9221, much like STAC9220.
Tested by: Devon H. O'Dell
- Set MIIF_NOLOOP as loopback doesn't work with this PHY. The MIIF_NOLOOP
flag currently triggers nothing but hopefully will be respected by
mii_phy_setmedia() later on.
- Use MII_ANEGTICKS instead of 5.
- Remove an unused macro.
- Fix some whitespace nits.
MFC after: 1 week
- In exphy_service() for the MII_TICK case don't bother to check whether
the currently selected media is of type IFM_AUTO as auto-negotiation
doesn't need to be kicked anyway.
- Remove #if 0'ed unapplicable code.
- Fix some whitespace nits.
MFC after: 1 week
and thus the FX_DIS pin indicates fibre media. This is part 1/2 of
adding support for the 100baseFX interface/port of AT-2700 series
adaptors.
Idea from: NetBSD
MFC after: 1 week
