ultra14f.c and eliminate constants.
Correct EISA slot scan loops to look at slots 1 to 15 inclusive (off
by 1 errors all over the place). Other drivers need this, I will get
to it after a little more work.
Correct the ultrastore EISA probe so that it starts after the last
EISA slot probed instead of starting over from slot 0.
We need an eisa.h to move a lot of common constants into. I will
write it if someone tells me where it should go (sys/eisa?).
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
Fixed the I/O statistics
Allow WD1007 type controllers to work
Support MULTI-BLOCK I/O
Correct delay to use port 0x84, reading the status register
might not be a long enough delay.
Changed probe message to match SCSI type devices.
to the user address space unless pcb_onfault is set. The code is currently
commented out because iBCS2 and process debugging parts of the kernel
need to be changed/fixed first.
probe of the device and shouldn't affect normal operation. It seems that
some version of the aic7870 are extreamly slow in clearing their interrupt
register so the added delay is required to ensure we don't poll a stale
interrupt value.
Clean up debugging printfs and stuff superflous output into #ifdef AHC_DEBUG.
Ensure that sdtrpending and wdtrpending are cleared in all cases after
we recieve an SDTR or WDTR message.
With this commit, the 294x should work or at least be much closer to
working properly.
with individual devices for each type of sound card:
opl, sb, sbxvi, sbmidi, pas, mpu, gus, gusxvi, gusmax, mss, uart
EXCLUDE_* options are no longer required to be included in the config file.
They are automatically determined by local.h depending on the devices
included.
Move #includes in local.h to os.h so files are included in the proper
order to avoid warnings.
soundcard.c now has additional code to reflect the device driver
routines needed.
Define new EXCLUDE_SB16MIDI for use in sb16_midi.c and dev_table.h.
#ifndef EXCLUDE_SEQUENCER or EXCLUDE_AUDIO have been added to
soundcard.c and sound_switch.c where appropriate.
Probe outputs changed to reflect new device names.
Readme.freebsd not needed. Update sound.doc with new config instructions.
Reviewed by: wollman
To use this: recompile src/gnu/usr.bin/cc, compile your kernel. The
files you want to profile should be compiled with '-a -g'. "strip -x"
the kernel and run. You don't need to profile all files in the kernel.
My next commit is the program to extract the data from the running kernel.
$Id$ information, and other code to make sound driver compile and work
correctly with FreeBSD.
Integrate changes obtained from Sujal Patel. These changes are:
o local.h: reverse option logic from EXCLUDE_* to AUDIO_*
o pas2_mixer.c: small addition
o ad1848.c: minor change with macro names
o sequencer.c: minor change with note check
o many spelling corrections in comments in about every other file
messages like this:
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <ST506>
wd0: size unknown, using BIOS values: 615 cyl, 4 head, 17 sec, bytes/sec 512
npx0 at 0xf0-0xff irq 13 on motherboard
npx0: changing root device to wd0a
^^^^^^
The spurious 'npx0: ' pops up if you have a 386 with a 387 FPU.
Make the sound configuration a little neater
(see /sys/i386/isa/sound/Readme.freebsd)
Add support for the Microsoft Sound Source.
Document the sound options again.
Submitted by: Sujal Patel <smpatel@wam.umd.edu>
Obtained from: Voxware
Let "grey delete" be a function key (default is 0x7f)
Fix the xor cursor again..
Made the backspace key generate del as default
Made CTRL-space generate nul as default.
Feb. 10th snapshot. The keyboard probe in the bootblock seems to
have been singled out as the cause of these problems, so I've beefed it
up alittle. This pushes us right up to the edge of the size limit:
the second stage boot is now 7152 bytes in size, just 8 bytes under
the wire. On the other hand, the new probe now does almost exactly
what syscons does, so hopefully this will do the trick. It seems
to work properly on my hardware, but then so did the old probe.
compiler.
Be carefull about over usage of volatile, it really killed performance
in a few areas and there was a better place to make things volatile in
almost all cases. The driver can now receive at full speed without RNR
errors.
New functions create - vm_object_pip_wakeup and pagedaemon_wakeup that
are used to reduce the actual number of wakeups.
New function vm_page_protect which is used in conjuction with some new
page flags to reduce the number of calls to pmap_page_protect.
Minor changes to reduce unnecessary spl nesting.
Rewrote vm_page_alloc() to improve readability.
Various other mostly cosmetic changes.
(a) bring back ttselect, now that we have xxxdevtotty() it isn't dangerous.
(b) remove all of the wrappers that have been replaced by ttselect
(c) fix formatting in syscons.c and definition in syscons.h
(d) add cxdevtotty
NOT DONE:
(e) make pcvt work... it was already broken...when someone fixes pcvt to
link properly, just rename get_pccons to xxxdevtotty and we're done
Include proper files for 2.x.
Remove old unused argument to ixreset (int uba)
Nolonger convert ether_type to host byte order.
Use arp_ifinit in place of arpwhohas.
Change cb_ias to be non volatile.
is close to 1000000 / 960 usec so the confusion probably didn't matter.
Test for COMCONSOLE before testing for RB_SERIAL so that the RB_SERIAL
test can be optimized away if COMCONSOLE is 1.
Simplify and Uniformize style of previous commit.
(b) add a function callback vector to tty drivers that will return a pointer
to a valid tty structure based upon a dev_t
(c) make syscons structures the same size whether or not APM is enabled so
utilities don't crash if NAPM changes (and make the damn kernel compile!)
(d) rewrite /dev/snp ioctl interface so that it is device driver and i386
independant
Removed screensavers from syscons, they are now LKM's. This makes it
possible to do some really "interesting" screensavers...
Fixed bug that sometimes caused garbage to appear when leaving
"scroll-lock" history.
Reformattet indentation, it got too deep for a normal 80 pos screen.
Split up in syscons.c & syscons.h for use with the saver-lkm's.
Temporarily removed -s option from vidcontrol, savers should now
be loaded with modload.
commands per target. I could have followed the route of the ncr driver
and gone to great lengths to get the SCSI subsystem to support more, but
I think I'll use the time saved to help Julian and Peter make tagged
queuing a better handled generic feature. This also includes some comment
and enum clean up and a possible fix for the hanging PCI controllers.
returned to user mode without enabling ASTs. The problem fixed itself
at the next syscall or non-FPU trap, if any. It hung the system for
a test process that masked SIGFPE's and divided by zero. The faulting
division was returned to endlessly and this gave plently of opportunities
for the swi_ast_phantom case to be reached; after it was reached the
system hung because the ASTs for preemption and SIGINT handling were
disabled.
just thinking about it.
Two changes need to be made to allow 'config kernel swap generic' to
work properly without requiring any compile-time flags:
/usr/src/usr.sbin/config/mkswapconf.c: we need to define a dummy stub
for the setconf() function to replace the one in swapgeneric.c that
isn't available in non-generic configurations.
/usr/src/sys/i386/i386/autoconf.c: the -a boot flag causes setroot()
to be skipped and lets setconf() prompt the user for a root device.
If you skip setroot() in a non-generic kernel, you could get severely
hosed. To avoid this, we silently ignore the -a flag if rootdev != NODEV.
(rootdev is always initialized to NODEV in swapgeneric.c, so if
we find that rootdev is something other than NODEV, we know we're
not using a generic configuration.)
briefly over it, and see some serious architectural issues in this stuff.
On the other hand, I doubt that we will have any solution to these issues
before 2.1, so we might as well leave this in.
Most of the stuff is bracketed by #ifdef's so it shouldn't matter too much
in the normal case.
Reviewed by: phk
Submitted by: HOSOKAWA, Tatsumi <hosokawa@mt.cs.keio.ac.jp>
Slice 0 is now for the first BSD slice. The first BSD slice is
the first DOSpartition with id 0xa5 or the whole disk if their
are no DOSpartitions (except the latter is not yet implemented).
Existing partitions on it work the same as in 2.0 except the
'd' partition is no longer special and partitions are relative
to the skice.
Slice 1 is now for the whole disk and gets a read-only label
describing the disk. Previously, slice 0 was for the whole disk
and there was no label on it.
Slices 2-31 are for DOSpartitions. Slice 0 is an alias for one
of these if there is a BSD slice. Previously, slices 1-31 were
for DOSpartitions.
diskslice_machdep.c:
Expand whole disk slice to include all DOSpartitions. More work
is required for >1024 cylinders and to rewrite the label iff the
driver is unsure about the geometry.
subr_diskslice.c:
New function dsisopen() to help handle media changes.
when ttselect() is improved. This requires using an array of tty structs
and not using ttymalloc().
Fix an off by 1 error. Some caclulations seem to be off by a factor
of NCY. NCY defaults to 16, which gives 256 tty structs occupying
0xd000 bytes. The minor number encoding only allows 16 ttys.
Update the types of timeout functions to 2.0.
It boots FreeBSD from a running MS-DOS system.
It's compiled using some MS-DOS tools, but there is a binary
hidden in the uuencoded file. (Go ahead, flame me if you can come up
with a solution for the problem. Just saying "this is bad" doesn't count!)
Rod, you were right: one would have to deal with weird interfaces to the
memory managers, and it seems that Christian found them all, and made them
work.
Thanks Christian!
Reviewed by: phk
Submitted by: DI. Christian Gusenbauer <cg@fimp01.fim.uni-linz.ac.at>
Christians README:
------------------
Hi Everybody!
This is version 1.5 of "fbsdboot", a program that allows you to boot a kernel
from a MS-DOS partition or a FreeBSD partition. This program runs using DOS.
It works with various memory managers (like EMM386, 386MAX) under certain
circumstances.
First, a FreeBSD kernel is always loaded to memory starting at 0x100000. To
assure that loading the kernel *does not* overwrite memory used by memory
managers, high memory for the kernel is allocated and after loading the kernel
it's moved to 0x100000.
Second, there are many ways to switch to protected mode which is necessary to
start the kernel. Each BIOS gives you the possibility to use INT15H (AH=89H)
to do that. But some memory-managers like 386max does not allow you to use
this method.
An other way to do the switch is to use DPMI services, but they do not
guarantee, that the protected mode application is executed with privilege
level 0. Therefore this method is *not* used.
VCPI services offer another way to switch to protected mode, and VCPI servers
are built into "emm386.exe", "386max" and "qemm". That's why, this method is
implemented in fbsdboot.exe.
Fbsdboot.exe tries to switch to protected mode using VCPI services. If they're
not available INT15H is used to do the switch. If that fails, it's not possible
for this version of fbsdboot.exe to boot a kernel :-(.
You can get commandline options of fbsdboot if you start it with "-?" as option!
I don't know, if fbsdboot works with QEMM, as I don't have the possibility to
test it.
Enjoy and have fun!
Christian.
cg@fimp01.fim.uni-linz.ac.at
PS: Many thanks to Bruce Evans for his assistance!
Submitted by: Rich
Make conditionals on BIOSWAIT consistent with usage in io.c.
If you had 'BOOTWAIT=0' in your /etc/make.conf then biosboot wouldn't
compile. It was '#if' in io.c and '#ifdef' in probe_keyboard.c so I
changed the latter to '#if'.
Even if BOOTWAIT is undefined then '#if BOOTWAIT' becomes
'#if 0' so it should compile either way with this change.
I took 53 and it was too late when Jordan sayd
it better been 60..besides i have no clue how to make it 60..
Jordan- pleeease don't kill me..(This is also useful(??) device..)
entire kernel.
Unfortunately we didn't send him a copy of the style guide before he did it.
I'm trying to find all the benign and downright sound bits and will commit
them without any other explanation than "YF fix" if they are merely cosmetic.
Reviewed by: phk
Submitted by: yves@dutncp8.tn.tudelft.nl (Yves Fonk)
add a an ioctl call to set the transfer block size (SNDCTL_DSP_SETBLKSIZE)
and add the select system call to the drivers. They also fix a problem with
the #EXCLUDE macros for the PAS-16 card.
Submitted by: Jim Lowe <james@blatz.cs.uwm.edu>
now we're back to the old way. By way of amends, I cleaned up all the
casting evils and generally neated this file up as much as possible. It
still, however, needs to die.
adapted to FreeBSD by Heikki Suonsivu <hsu@cs.hut.fi>.
Submitted by: Andrew Werple <andrew@werple.apana.org.au> and
Heikki Suonsivu <hsu@cs.hut.fi>
Obtained from: NetBSD
1. add iosize command, and show it in `ls'
2. add a probe command
3. add an attach command
[the latter 2 do the obvious thing - call the device's routine and print the
status returned].
You will normally have to have a VLB or other 32bit IDE "controller" for
this to work.
Depending on your setup, this may gain you 20-100 % speed from your disk.
Reviewed by: phk
Submitted by: vak@cronyx.ru
message instead of relying on the fact that we are scheduled to send them.
The old method worked 99.9% of the time, but someone reported some periferals
that did MSG_REJECT at odd times (sometimes before we could send an SDTR
or WDTR) that we would construe as the response to an SDTR or WDTR message.
This also removes a possible race condition where after a bus reset (the
result of a command time out not during intial probe time), we might queue
two commands both requesting SDTR, WDTR or both.
some comparisons as it is more correct (we want the kernel page tables
included).
Reorganized some of the expressions for efficiency.
Fixed the new pmap_prefault() routine - it would sometimes pick up the
wrong page if the page in the shadow was present but the page in object
was paged out. The routine remains unused and commented out, however.
Explicitly free zero reference count page tables (rather than waiting
for the pagedaemon to do it).
Submitted by: John Dyson
Submitted by: wolf (Wolfgang Stanglmeier)
Most PCI specific files moved from sys/i386/pci to sys/pci.
One PC specific file (pcibus.c) new in sys/i386/isa.
