Reorder how the pci probing in handled. before adding devices, check to
see if the slot is a multi-function device to see if we should probe all
the functions.
Original idea by: imp
drivers that implemnt the i2c bit banging bus interface not have to
recompile iicbb in order to add an attachment for it.
This will mean the bktr and other definitions can go back to their
respective drivers.
- Mark that it cannot handle greater than 4GB of RAM at this time. Fixing
that will come later. Fail any attempts to dump above thati limit.
- If a call to aac_disk_dump() needs to be split into multiple i/o's,
increment the virtual offset after each i/o instead of just dumping the
same offset over and over again.
- Bail out if bus_dmamap_load() returns an error. Error recovery is likely
not possible.
This version of the driver code is compatible with near-release FreeBSD 5.1
kernel/driver interfaces.
modules/Makefile, man page and other bindings to follow shortly, once I get
this part of the check-in right.
Approved by: markm(mentor)
Previously, any normal I/O on an fdc(4) device would fail with ENXIO
if the device had been opened in non-blocking mode and then closed
prior to the conventional access; that would last until the floppy
disk was ejected and re-inserted to raise the unit attention condition.
Add a clarifying comment.
populated. Apparently, if you use an ehci controller, it's not.
Use usbd_device2interface_handle() to retrieve the interface handle.
NOTE: uaa->iface is populated in the probe routine, so I suspect the
fact that it's NULL in the attach routine is a bug in the ehci driver.
Also, don't depend on the PHY addresses returned by the AXE_CMD_READ_PHYID
command. The address is correct for my LinkSys NIC, but a user has
reported that with a D-Link NIC, the PHYID command returns address 4
while the attached Broadcom PHY is in fact strapped for address 0.
Instead, latch onto the first PHY address that returns valid data
during a readreg operation.
as should every block device strategy routine.
There was at least one evil consequence of not doing so:
Some errors returned by fdstrategy() could be lost (EAGAIN,
in particular.)
PR: kern/52338 (in the audit-trail)
Discussed with: bde
to access floppy parameters through it.
Note: The DIOCGSECTORSIZE and DIOCGMEDIASIZE handlers withing
fdioctl() couldn't be just moved to below the existing check
for blocking mode because fd->ft can be non-NULL while still
in non-blocking mode (fd->ft can be set with the FD_STYPE ioctl.)
PR: kern/52338
No MFC: Not applicable to STABLE
ulpt_status() afterwards. This fixes a crash that can occur if a
USB printer is power-cycled when printing is just starting. The
problem is similar to that fixed in revision 1.33, but it is much
less likely to occur.
MFC after: 1 week
and return NULL.
vinum_scandisk: Don't handle NULL device pointers.
Only look at compatibility partition for i386. This
is a kludge which should go away once I have adequate
documentation for the New World Order.
Together, these fixes remove occasional error messages about
non-existent drives. They may also fix a number of problems that have
been reported without a PR.
PRs: None
Devices below may experience a change in geometry.
* Due to a bug, aic(4) never used extended geometry. Changes all drives
>1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.
For all other controllers in this commit, this should be a no-op.
Looked over by: scottl
how we registered pccard_intr, it is MPSAFE. However, since we
register the pccard_intr handler with the flags of the ISR we call,
that is the gating factor. We need do nothing specific here.
Prompted by: seeing pccard_intr in a panic.
are the same that those of the kernel in the KLD_MODULE case. If
we ever want to detect that kind of problems, this is not the right
place to do this since every network driver would be affected by
such desynchronisation.
toggle several media options (sonet/sdh, for example) with ifconfig and
to see the carrier state in ifconfig's output. It gives also read/write
access (given the right privilegs) to the S/Uni registers to user space
programs.
than once. This appears to work around the hanging issues, at the
expense of warnings about bad RID allocations. I'm not sure this is a
permanant workaround, but does appear to help in the tests that I've
done here.
It currently supports the PMC Sierra Lite, Ultra and 622 chips and
the IDT 77105. The driver handles media options and state in a consistent
manner for ATM drivers. The next commit to the midway driver will make
it use utopia.
doesn't have one. The test was bogus on these architectures, but
recent changes broke it altogether.
Prompted by: phk
This should fix the recent SPARC 64 build problems.
