specially crafted module. There are several handrolled sollutions to this
problem in the tree already which will be replaced with this. They include
iwi(4), ipw(4), ispfw(4) and digi(4).
No objection from: arch
MFC after: 2 weeks
X-MFC after: some drivers have been converted
The sys/sys/stddef.h is here for some time now to fulfil the
kernel needs. It also was not reliable due to the exists(@)
check: in an empty module directory, "make depend; mv .depend
.depend~; make depend" ran mkdep(1) with different arguments.
gdb(1) command better, though I must admit it's confusing: these
files have not only [debugging] symbols, but much more than that.
Requested by: obrien
our kernel linker will only load PT_LOAD segments, apparently not.
Instead, produce .dbg objects from .debug objects, and install
them together with non-debug objects, as described in objcopy(1).
Original code by: obrien
Try to make everyone happy: David (to have debug kernels installed
by default), Warner (to be able to override that), and myself (for
actually making it all work and to be consistent).
Now, if kernel was configured for debugging (through DEBUG=-g in
the kernel config file or "config -g"), doing "make install" will
install debug versions of kernel and module objects with their
canonical names,
kernel.debug -> /boot/kernel/kernel
if_fxp.ko.debug -> /boot/kernel/if_fxp.ko
Installing a kernel not configured for debugging, or debug kernel
with INSTALL_NODEBUG variable defined, will install non-debug
kernel and module objects.
Also, restore the install.debug and reinstall.debug targets that
are part of the existing API (they cause some additional gdb(1)
scripts to be installed).
modules along with kernel.
After this change it is possible to embrace opt_*.h includes with ifdef
HAVE_KERNEL_OPTION_HEADERS. And thus, avoid editing a lot of Makefiles
in modules directory each time we introduce a new opt_xxx.h.
Requested by: bde
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
followed by "make depend" shouldn't do anything. It doesn't
seem to be a problem anymore, and if someone finds it to break
again, please contact me so we can work on a real fix.
Reviewed by: bde
- Sort kmod.mk knobs in the documentation section.
- Fixed misuses of the word "KLD" which stands for
"kernel ld", or "kernel linker", where kernel
module is meant.
- Removed redundant uses of ${.OBJDIR}.
- Whitespace and indentation fixes.
- CLEANFILES cleanup.
- Target redefinition protection (install.debug).
Submitted by: bde, ru
Reviewed by: ru, bde
that was fixed by this should not normally happen, and since I did not
record the traces of my failed build attempt that had been solved with
that change, it's not entirely clear whether it hadn't been a pilot
error on my end. In dubio pro reo. :-)
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
namespace. This is to allow decoupling of attachments from ACPI where they
need some functionality when ACPI is present but do not want to require ACPI
to always be loaded.
your (network) modules as well as any userland that might make sense of
sizeof(struct ifnet).
This does not change the queueing yet. These changes will follow in a
seperate commit. Same with the driver changes, which need case by case
evaluation.
__FreeBSD_version bump will follow.
Tested-by: (i386)LINT
all of the interface between the driver and the bus. This will enable
us to stop special casing eisa bus attachments in modules and treat them
like we treat all other busses.
In the longer run, we need to eliminate much (all?) of these interfaces
and switch to using the standard bus_alloc_resource(), but that's not
done right now.
# I've not updated the modules to include eisa, etc, just yet
Tested on: Compaq Proliant 3000/333 purchased for eisa work
converts miidevs to a .h file, so rename to reflect that.
The usb and pccard versions have also been renamed and will be hooked
into the build system shortly (I've made the conversion in my p4
tree).
yet, but building kld's is OK now and they can be loaded by kldload(2).
(but the machine will likely crash soon afterwards, a "minor" problem :-)
Brought to you by: my injured knee (from moving)
Fix 'broken' ifdefs.
icc does not support profiling yet so remove unfinished code which was
supposed to help.
Submitted by: netchild (original version)
Reviewed by: ru
Intel C/C++ compiler (lang/icc) to build the kernel.
The icc CPUTYPE CFLAGS use icc v7 syntax, icc v8 moans about them, but
doesn't abort. They also produce CPU specific code (new instructions
of the CPU, not only CPU specific scheduling), so if you get coredumps
with signal 4 (SIGILL, illegal instruction) you've used the wrong
CPUTYPE.
Incarnations of this patch survive gcc compiles and my make universe.
I use it on my desktop.
To use it update share/mk, add
/usr/local/intel/compiler70/ia32/bin (icc v7, works)
or
/usr/local/intel_cc_80/bin (icc v8, doesn't work)
to your PATH, make sure you have a new kernel compile directory
(e.g. MYKERNEL_icc) and run
CFLAGS="-O2 -ip" CC=icc make depend
CFLAGS="-O2 -ip" CC=icc make
in it.
Don't compile with -ipo, the build infrastructure uses ld directly to
link the kernel and the modules, but -ipo needs the link step to be
performed with Intel's linker.
Problems with icc v8:
- panic: npx0 cannot be emulated on an SMP system
- UP: first start of /bin/sh results in a FP exception
Parts of this commit contains suggestions or submissions from
Marius Strobl <marius@alchemy.franken.de>.
Reviewed by: silence on -arch
Submitted by: netchild
to one, DEBUG_FLAGS, which is also compatible with <bsd.prog.mk>.
Previously one had to set both DEBUG and DEBUG_FLAGS to build the
.ko.debug with debugging symbols which was boring when doing this
manually.
