subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
there is no irq link. Since we now use the stored copy of PRT, not the
one that used to be passed into acpi_pcib_route_interrupt(), we need it in
the list. [1]
Fix a bug in acpi_pci_find_prt() where we weren't checking the bus, thus
choosing the wrong PRT entry to use for routing the link. Also, add a
printf for the case where the PRT entry is not found as this should not
happen.
Tested by: marcel [1]
incomplete in that the PRT routing was not aware of link programming.
Fix this by doing all routing through the link devices. The new algorithm
for setting up links is:
1. Read _CRS to get current setting. If invalid (not in _PRS), then set
to 0.
2. Attempt to call _DIS on the link. If successful, mark the link as not
routed. Otherwise, assume it still is.
Then when a routing request occurs:
3. Update weights for all IRQs
4. Attempt to route the initial IRQ if valid
5. If that fails, walk through the sorted list, attempting to route IRQs.
6. Configure the trigger/polarity based on _PRS.
Other changes:
* Add acpi_pci_find_prt() to look up the PRT entry for a given device and
acpi_pci_link_route() to select/route the best IRQ for it.
* Remove duplicated code in acpi_pcib_route_interrupt() that picked the
first IRQ from _PRS.
* Remove unneeded arguments from acpi_pcib_resume() and friends.
* Ignore _STA on link devices but report if it seems strange.
* Add a prt_source handle to the PRT structure since the ACPI struct
ACPI_PCI_ROUTING_TABLE uses a fixed-size entry for it. We'll need to
dynamically size this object if we want to use it the same way ACPI-CA
does. Null-terminate the source.
Tested by: Luo Hong <luohong99_at_mails.tsinghua.edu.cn>,
Jeffrey Katcher <jmkatcher_at_yahoo.com>
Info from: jhb, Len Brown (Intel)
if_start routines cannot currently be entered without Giant. When
the kernel is running with debug.mpsafenet != 0, this will defer
if_start execution to a task queue thread holding Giant, which may
introduce additional latency, but avoid incorrect execution.
Suggested by: dfr
full, avoiding the cost of mutex operations if it is. We re-test
once the mutex is acquired to make sure it's still true before doing
the -modify-write part of the read-modify-write. Note that due to
the maximum fifo depth being pretty deep, this is unlikely to improve
harvesting performance yet.
Approved by: markm
chipsets, based on Linux's via-agp.c. On boot, the system selects which AGP
version to use based on the inserted card. If v2 was chosen, the chipset
needs to be programmed with the v2 registers still. Also included in kern/69953
are changes to make the programming of the v3 registers match linux, but that
will be left out until the need to do so is confirmed (want specs or a tester).
PR: kern/69953
Submitted by: Oleg Sharoiko <os@rsu.ru>
Tested by: Oleg Sharoiko <os@rsu.ru>, Geoff Speicher <geoff@speicher.org>
(full version from PR)
o Change the motion calculation to result in
a more reasonable speed of motion
This should fix the 'aiming' problems people have reported. It also
mitigates (but doesn't completely solve) the 'stalling' problems at
very low speeds.
Tested by: many subscribers to -current
Approved by: njl
o Catch 'taps' as button presses
o One finger sends button1, two fingers send button3,
three fingers send button2 (double-click)
Tested by: many subscribers to -current
Approved by: njl
o Handle the 'up/down' buttons some touchpads have as
a z-axis (scrollwheel) as recommended by the specs
o Report the buttons as button4 and button5 instead
of button2 and button4, button2 can be emulated by
pressing button1 and button3 simultaneously. This
allows one to use the two extra buttons for other
purposes if one so desires.
Tested by: many subscribers to -current
Approved by: njl
o Clean up whitespace and comments in the
enable_synaptics() probing function
o Only use (and rely on) the extended capability
bits when we are told they actually exist
o Partly ignore the (possibly dated?) part of the
specification about the mode byte so that we
can support 'guest devices' too.
Tested by: many subscribers to -current
Approved by: njl
was being unconditionally dereferenced but was NULL for PIO requests.
Check the request flags for a DMA transaction before dereferencing.
Reported by: ceri
Tested by: Radek Kozlowski <radek -at- raadradd.com>
with it that need to be understood better before they can be resolved.
This takes time and time is already in short supply.
Reported & tested by: glebius@
message if they are incorrect. Also, remove the hack of allowing the
initial irq setting to not be in _PRS. As before, the old behavior can be
regained by defining ACPI_OLD_PCI_LINK.
want a splash screen.
There seems to be some confusion in the syscons code as to the meaning of
the SC_KERNEL_CONSOLE flag. Its absence is sometimes interpreted to mean
"I am not the system console", and sometimes to mean "I am not the only
VGA console" (see the font loading code for an example of the latter).
Someone with better syscons fu than myself should take a closer look.
following behavior:
* Link devices return invalid status (_STA) values. The results are very
unreliable -- sometimes never present. Just ignore the status and pick
the best configuration from _PRS.
* Link devices return invalid current settings (_CRS). Even after setting
the link value, many systems still return a different setting for _CRS.
When setting an IRQ, don't bother to check _CRS to see if we succeeded.
Note that we still check _CRS before routing and this should be addressed
as well.
Since this is a sensitive area, leave the old behavior accessible via
uncommenting the define for ACPI_OLD_PCI_LINK at the top of the file. Once
this has been thoroughly tested, this option and the code it covers will
be removed.
Thanks to Len Brown at Intel for informing us of these issues as he worked
around them in Linux.
Since HME doesn't compensate the checksum for UDP datagram which
can yield to 0x0, UDP transmit checksum offload is disabled by
default. The UDP Transmit checksum offload can be reactivated
by setting special link option link0 with ifconfig(8).
Approved by: jake (mentor)
Reviewed by: tmm
Tested by: Herve Boulouis <amon@sockar.homeip.net>
by a transaction performing a driver handled message sequence (an
scb with the MK_MESSAGE flag set).
SCBs that perform host managed messaging must always be
at the head of their per-target selection queue so that
the firmware knows to manually assert ATN if the current
negotiation agreement is packetized. In the past we
guaranteed this by queuing these SCBs separarately in
the execution queue. This exposes the system to potential
command reordering in two cases:
1) Another SCB for the same ITL nexus is queued that does
not have the MK_MESSAGE flag set. This SCB will be
queued to the per-target list which can be serviced
before the MK_MESSAGE scb that preceeded it.
2) If the target cannot accept all of the commands in the
per-target selection queue in one selection, the remainder
is queued to the tail of the selection queues so as to
effect round-robin scheduling. This could allow the
MK_MESSAGE scb to be sent to the target before the
requeued commands.
This commit changes the firmware policy to defer queuing
MK_MESSAGE SCBs into the selection queues until this can
be done without affecting order. This means that the
target's selection queue is either empty, or the last
SCB on the execution queue is also a MK_MESSAGE SCB.
During any wait, the firmware halts the download of new
SCBs so only a single "holding location" is required.
Luckily, MK_MESSAGE SCBs are rare and typically occur only
during CAM's bus probe where only one command is outstanding
at a time. However, during some recovery scenarios, the
reordering *could* occur.
aic79xx.c:
Update ahd_search_qinfifo() and helper routines to
search for pending MK_MESSAGE scbs and properly
restitch the execution queue if either the MK_MESSAGE
SCB is being aborted, or the MK_MESSAGE SCB can be
queued due to the execution queue draining due to
aborts.
Enable LQOBUSFREE status to assert an interrupt.
This should be redundant since a BUSFREE interrupt
should always occur along with an LQOBUSFREE event,
but on the Rev A, this doesn't seem to be guaranteed.
When a PPR request is rejected when a previously
existing packetized agreement is in place, assume
that the target has been reset without our knowledge
and revert to async/narrow transfers. This corrects
two issues: the stale ENATNO setting that was used
to send the PPR is cleared so the firmware is not
confused by a future packetized selection with
ATN asserted but no MK_MESSAGE flag in the SCB and
it speeds up recovery by aborting any pending
packetized transactions that by definition are now
dead.
When re-queueing SCBs after a failed negotiation
attempt, ensure command ordering by freezing the
device queue first.
Traverse the list of pending SCBs rather than the
whole SCB array on the controller when pushing
MK_MESSAGE flag changes out to the controller.
The original code was optimized for the aic7xxx
controllers where there are fewer controller slots
then pending SCBs and the firmware picks SCB
slots. For the U320 controller, the hope is
that we have fewer pending SCBs then the 512
slots on the controller.
Enhance some diagnostics.
Factor out some common code.
aic79xx.h:
Add prototype for new ahd_done_with_status() that is
used to factor out some commone code.
aic79xx.reg:
Add definisions for the pending MK_MESSAGE SCB.
aic79xx.seq:
Defer MK_MESSAGE SCB queing to the execution queue
so as to preserve command ordering. Re-arrange some
of the selection processing code so the above change
had no performance impact on the common code path.
Close a few critical section holes.
When entering a non-packetized phase, manually enable
busfree interrupts, since the controller hardware
does not do this automatically.
aic79xx_inline.h:
Enhance logging for queued SCBs.
aic79xx_osm.c:
Add new a new DDB ahd command, ahd_dump, which
invokes the ahd_dump_card_state() routine on the
unit specified with the ahd_sunit DDB command.
aic79xx_pci.c:
Turn on the BUSFREEREV bug for the Rev B. controller.
This is required to close the busfree during non-packetized
phase hole.
into single-user mode (as seen on sparc64 and PPC). Problems were due
to a minor oversight in the changes committed in revision 1.25.
Submitted by: grehan
Tested by: gad & yongari
unconditionally, stop after the first one (system board) if no EISA hardware
is detected. This fixes a boot hang (i.e. Thinkpad) when ACPI is disabled.
Also, split the probe code into a separate function and do some style cleanup.
Note that the Adaptec 2842 VLB controller probe is broken by this change
and will fail to probe. It should be fixed separately.
in case of a CHECK CONDITION.
- Make this driver return SCSI status information.
- While here, factor out the clearing of the CAM status from every
element of the switch statement to only once before the switch.
This fixes burning CDs with recent cdrecord 2.01 alpha versions and
burners attached to asr(4) controllers but there could have been
other applications and da(4) etc. also affected.
Reviewed by: gibbs, scottl
MFC after: 2 weeks
skip blocks that are too big by a factor of two or greater. This
avoids some cases of extremely inefficient memory use that can occur
when large (e.g. 64k) blocks on the free list get used when allocating
a 4k chunk of 64-byte fragments. Because fragments have their own
free list, the 60k difference got lost forever every time.
system BIOS to disable legacy device emulation as per the "EHCI
Extended Capability: Pre-OS to OS Handoff Synchronisation" section
of the EHCI spec. BIOSes that implement legacy emulation using SMIs
are supposed to disable the emulation when this procedure is performed.
so that they know whether the allocation is supposed to be able to sleep
or not.
* Allow uma_zone constructors and initialation functions to return either
success or error. Almost all of the ones in the tree currently return
success unconditionally, but mbuf is a notable exception: the packet
zone constructor wants to be able to fail if it cannot suballocate an
mbuf cluster, and the mbuf allocators want to be able to fail in general
in a MAC kernel if the MAC mbuf initializer fails. This fixes the
panics people are seeing when they run out of memory for mbuf clusters.
* Allow debug.nosleepwithlocks on WITNESS to be disabled, without changing
the default.
Both bmilekic and jeff have reviewed the changes made to make failable
zone allocations work.
now, but it's possible for ndis_reset_nic() to sleep (sometimes the
MiniportReset() method returns NDIS_STATUS_PENDING and we have
to wait for completion). To get around this, execute the ndis_reset_nic()
routine in the NDIS_TASKQUEUE thread.
to be particularly correct or optimal, but it seems to be enough
to allow the attachment of USB2 hubs and USB2 devices connected via
USB2 hubs. None of the split transaction support is implemented in
our USB stack, so USB1 peripherals will definitely not work when
connected via USB2 hubs.
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
submitted version with style cleanups and changes to comments. I also
modified the ioctl interface. This version only has one ioctl (to get
the Synaptics-specific config parameters) since this is the only
information a user might want.
Submitted by: Arne Schwabe <arne -at- rfc2549.org>
* Some systems have _FDE and child floppy devices, but no _FDI. This seems
to be compatible with the standard. Don't error out if there is no _FDI.
Instead, continue on to the next device. The normal fd probe will take
care of this device.
* Some systems have _FDE but no child devices in AML. For these, add a
second pass that compares the results of _FDE to the presence of devices.
If not present, add the missing device.
* Some BIOS authors didn't read the spec. They use tape drive values for
all fdc(4) devices. Since this isn't grossly incompatible with the
required boolean value, use them. They also define the _FDE items as a
package instead of buffer. Regenerate the buffer from the package if it
is present.
Tested by: tjr, marcel
ACPI_DEBUG. This upset the ordering that acpi_probe_order() was meant to
provide, causing devices to attach before the sysresource object. This
debugging feature has been unnecessary for a while so just remove it.
Testing by: marcel
Properly wait for not busy and introduce a timeout for devices not
setting busy (as they should).
Leave a printf in there that states how long the wait was, as I'd like
to get an idea of the variations here. The time needed seems also to be
affected by whether a medium is present or not.
FOREACH_SAFE. Remove bad cast of retp and instead use an additional
arg to pass back the number of valid outputs. Use the package convenience
functions for parsing packages.
(in particular, bge(4) hasn't supported rxcsum since if_bge.c#1.5)
Clean up some aspects of capabilities usage, i.e. stop using
if_hwassist to see whether we are doing offload now because if_hwassist
is for TCP/IP layer and it is subordinate to if_capenable.
Thanks to: Aled Morris for donating a nice bge(4) NIC to me
Reviewed by: -net, -hackers (silence)
happens because the sio device was never opened and com->tp is
therefore NULL. ttygone can't swallow a NULL, so guard against that
possibility. Other places in this function make similar checks, so I
believe this is correct.
Improve child_detached a little and make it conform better to
style(9). Also, improve comment about what we'll be doing in the
future about driver_added. Soon it will be possible to kldload usb
drivers and have them attach w/o a need to disconnect/reconnect them.
the data sheets leads me to believe these will just work. Those parts
with the various media readers on them may not have the required
FreeBSD drivers that will attach to the subdevices that will be seen
on some of these parts.
PCI 1515, 1530, 1620, 4520, 6411, 6420, 7410, 7510, 7610
Prompted by: Havard Eidnes
These are from the datasheets downloaded from TI's web site.
They describe the PCI[67]x[12]1 and PCI[67]x20 parts, with and without
the smartcard enabled.
Also introduce a macro to be called by persistent nodes to signal their
persistence during shutdown to hide this mechanism from the node author.
Make node flags have a consistent style in naming.
Document the change.
usbdi.c rev. 1.104, author: mycroft
ugen_isoc_rintr() may recycle the xfer immediately. Therefore, we
avoid touching the xfer after calling the callback in
usb_transfer_complete(). From PR 25960.
left around after the PCI probe, acpi_video stopped attaching because while
it was an acpi child device, it really is a PCI device. Fix this by making
it a PCI child.
* Remove non-handle ivars accesses since child busses only implement
acpi_get_handle().
* Access the acpi softc directly through the devclass instead of through
the implied parent.
* Clean up a potential panic on unload by freeing the sysctl context before
storing NULL in the OID.
Found by: marks
- `sound'
The generic sound driver, always required.
- `snd_*'
Device-dependent drivers, named after the sound module names.
Configure accordingly to your hardware.
In addition, rename the `snd_pcm' module to `sound' in order to sync
with the driver names.
Suggested by: cg
future:
rename ttyopen() -> tty_open() and ttyclose() -> tty_close().
We need the ttyopen() and ttyclose() for the new generic cdevsw
functions for tty devices in order to have consistent naming.
rev. 1.67, author: mycroft
Fix a byte order error.
rev. 1.68, author: mycroft
Adjust some silliness that was causing us to do extra work for
"frame list rollover" interrupts, which we pretty much ignore.
Obtained from: NetBSD
hints-based probe to fdc_hints_probe().
Also:
* Fix some resource leaks when attach fails.
* Remove the FDC_ATTACHED flag. It was supposed to prevent multiple
unloads but this is not necessary.
allows a bus to re-enumerate its child handles and optionally replace
them with new children, arranged to the bus's liking. (The current device
space is flat with all devices immediately under acpi0). Add comments
for each interface.
for unknown events.
A number of modules return EINVAL in this instance, and I have left
those alone for now and instead taught MOD_QUIESCE to accept this
as "didn't do anything".
when the battery is fully charged. That breaks some of the arithmetic in
calculating the remaining capacity (ends up with more than 100%).
This commit makes sure the max is 100.
Approved by: njl
