* Failall is now named just that.
* Add TX ok and TX fail, for aggregate frame sub-frames.
This will break athstats; a followup commit wil resolve this.
Sponsored by: Hobnob, Inc.
Because there is no reliable way to know whether RX MAC is in
stopped state, rejecting all frames would be the only way to
minimize possible races.
Otherwise it's possible to receive frames while stop command
execution is in progress and controller can DMA the frame to freed
RX buffer during that period.
This was observed on recent PCIe controllers(i.e. RTL8111F).
While this change may not be required on old controllers it
wouldn't make negative effects on old controllers. One side effect
of this change is disabling receive so driver reprograms RL_RXCFG
to receive WOL frames when it is put into suspend or shutdown.
This should address occasional 'memory modified free' errors seen
on recent RealTek controllers.
driver would ignore the first link state update if controller
already established a link such that it would have to take
additional link state handling in re_tick().
access.
While I'm here, enable WOL through magic packet but disable waking
up system via unicast, multicast and broadcast frames. Otherwise,
multicast or unicast frame(e.g. ICMP echo request) can wake up
system which is not probably wanted behavior on most environments.
This was not known as problem because RL_CFG5 register access had
not effect until this change.
The capability to wake up system with unicast/multicast frames
are still set in driver, default off, so users who need that
feature can still activate it with ifconfig(8).
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
bit should not affect link establishment process of auto-negotiation
if manual configuration is not used, which is true in auto-negotiation.
However it seems setting this bit interfere with IP1001 PHY's
down-shifting feature such that establishing a 10/100Mbps link failed
when 1000baseT link is not available during auto-negotiation process.
Tested by: Andrey Smagin <samspeed <> mail dot ru >
Pause timer value is initialized to 0xFFFF. Controller allows just
4 different TX pause thresholds. The lowest possible threshold
value looks too aggressive so use next available threshold value.
and proc_getenvv(), which were implemented using linprocfs_doargv() as
a reference.
Suggested by: kib
Reviewed by: kib
Approved by: des (linprocfs maintainer)
MFC after: 2 weeks
- Remove MIIBUS statchg callback and program VGE_DIAGCTL before
initiating link establishment. Previously driver used to
program VGE_DIAGCTL after getting a link in statchg callback.
It seems the VGE_DIAGCTL register works like a kind of MII
register such that it requires setting a 'to be' mode in advance
rather than relying on resolved speed/duplex of established link.
This means the statchg callback is not needed in driver. In
addition, if there was no link at the time of media change, this
was not called at all.
- Introduce vge_ifmedia_upd_locked() to change current media to
configured one. Actual media change is performed only after PHY
reset and VGE_DIAGCTL setup.
- In WOL configuration, make sure to clear forced mode such that
controller can rely on auto-negotiation.
- Unlike most other drivers that use miibus(4), vge(4) used
controller's auto-polling feature for link state tracking via
interrupt. This came from controller's inefficient mechanism to
access MII registers. On link state change interrupt, vge(4)
used to get current link state with series of MII register
accesses. Because vge(4) already enabled auto polling, read PHY
status register to resolved speed/duplex/flow control parameters.
vge(4) still does not drive MII_TICK to reduce number of MII
register accesses which in turn means the driver does not know the
status of auto-negotiation. This was a one of long standing
issue of vge(4). Probably driver may be able to implement a timer
that keeps track of auto-negotiation state and restart
auto-negotiation when driver couldn't establish a link within a
specified period. However the controller does not provide a
reliable way to detect auto-negotiation failure so I'm not sure
whether it's worth to implement it in driver.
Alternatively driver can completely disable MII auto-polling and
let miibus(4) poll link state by driving MII_TICK. This may reduce
unnecessary overhead of stopping/restarting MII auto-polling of
controller. Unfortunately it was known that some variants of
controller does not work correctly if MII auto-polling is disabled.
environment strings and ELF auxiliary vectors from a process stack.
Make sysctl_kern_proc_args to read not cached arguments from the
process stack.
Export proc_getargv() and proc_getenvv() so they can be reused by
procfs and linprocfs.
Suggested by: kib
Reviewed by: kib
Discussed with: kib, rwatson, jilles
Tested by: pho
MFC after: 2 weeks
and DEVMETHOD() we can fully hide the explicit mention of kobj(9) from
device drivers.
- Update the example in driver.9 to use DEVMETHOD_END.
Submitted by: jhb
MFC after: 3 days
__FreeBSD_kernel__ indicates that this system uses the kernel of FreeBSD,
which by definition is always true on FreeBSD. This macro is also defined
on other systems that use the kernel of FreeBSD, such as GNU/kFreeBSD.
It is tempting to use this macro in userland code when we want to enable
kernel-specific routines, and in fact it's fine to do this in code that
is part of FreeBSD itself. However, be aware that as presence of this
macro is still not widespread (e.g. older FreeBSD versions, 3rd party
compilers, etc), it is STRONGLY DISCOURAGED to check for this macro in
external applications without also checking for __FreeBSD__ as an
alternative.
Approved by: kib (mentor)
MFC after: 2 weeks
vnode locking for read, readdir, readlink, getattr and access.
It is hoped that this will improve server performance for these
operations, since they will no longer be serialized for a given
file/vnode.
This fixes panics that users have been seeing when operating in station mode,
where the interface undergoes a lot more resets then in hostap mode (ie whilst
doing channel scanning.)
Reported by: arundel, wblock@wonkity.com
Sponsored by: Hobnob, Inc.
passed over to the runtime firmware on 6050 devices. Instead let
the runtime firmware do the calibration itself. This fixes support
for the 6050 series devices.
Obtained from: OpenBSD
Submitted by: kevlo
Tested by: lx, Tz-Huan Huang(earlier version)
Manual pages from OpenSolaris svn_134 are still properly CDDL licensed
but I have been informed that the parts from s11ex are uncertain even
if they contain a CDDL header.
- Don't deduct wired pages from total usable counts because it does not
make any sense. To make things worse, on systems where swap size is
smaller than physical memory and use a lot of wired pages (e.g. ZFS),
tmpfs can suddenly have free space of 0 because of this;
- Count cached pages as available; [1]
- Don't count inactive pages as available, technically we could but that
might be too aggressive; [1]
[1] Suggested by kib@
MFC after: 1 week
