- disable jumbo frame support on strict alignment architectures due
to the limitation of hardware. The driver needs a fix-up code for
RX side. The fix will show up in near future.
- fix endian issue for 82544 on PCI-X bus. I couldn't test this as
I don't have the NIC/hardware.
- prefer PCIR_BAR to hardcoded EM_MMBA.
- Properly checks for for 64bit BAR [1]
- replace inl/outl with bus_space(9) [1]
- fix endian issue on VLAN handling.
- reorder header files and remove unnecessary one.
Reviewed by: cognet
No response from: pdeuskar, tackerman
Obtained from: OpenBSD [1]
reclamation synchronously from get_pv_entry() instead of
asynchronously as part of the page daemon. Additionally, limit the
reclamation to inactive pages unless allocation from the PV entry zone
or reclamation from the inactive queue fails. Previously, reclamation
destroyed mappings to both inactive and active pages. get_pv_entry()
still, however, wakes up the page daemon when reclamation occurs. The
reason being that the page daemon may move some pages from the active
queue to the inactive queue, making some new pages available to future
reclamations.
Print the "reclaiming PV entries" message at most once per minute, but
don't stop printing it after the fifth time. This way, we do not give
the impression that the problem has gone away.
Reviewed by: tegge
in the hardware interrupt context (even if it is likely just an
ithread). We don't document that suspend/resume routines are run from
such a context and some of the things that happen in those routines
aren't interrupt safe. Since there's no real need to run from that
context, this restores assumptions that suspend routines have made.
This fixes Thierry Herbelot's 'Trying to sleep while sleeping is
prohibited' problem.
nearly identical to wintel/ia32, with a couple of tweaks. Since it is
so similar to ia32, it is optionally added to a i386 kernel. This
port is preliminary, but seems to work well. Further improvements
will improve the interaction with syscons(4), port Linux nforce driver
and future versions of the xbox.
This supports the 64MB and 128MB boxes. You'll need the most recent
CVS version of Cromwell (the Linux BIOS for the XBOX) to boot.
Rink will be maintaining this port, and is interested in feedback.
He's setup a website http://xbox-bsd.nl to report the latest
developments.
Any silly mistakes are my fault.
Submitted by: Rink P.W. Springer rink at stack dot nl and
Ed Schouten ed at fxq dot nl
to user-space if a parameter named "errmsg" is passed into the iovec.
Used in conjunction with vfs_mount_error(), more useful error messages
than errno can be passed back to userspace when mounting a filesystem
fails.
Discussed with: phk, pjd
have started aio, instead, initialize aio management structure
if it hasn't been done, the reason to adjust this behavior is
to make it a bit friendly for threaded program, consider two
threads, one submits aio_write, and another just calls
aio_waitcomplete to wait any I/O to be completed and recycle the
aio requests, before submitter doing any I/O, the recycler wants
to wait in kernel. This also fixes inconsistency with other aio
syscalls.
This hasn't been true on i386 for at least a decade, probably longer, but
I'm too lazy to look up the exact year that PAE support was introduced.
Thus, this driver doesn't work on PAE.
X-MFC After: now
softc lists and associated mutex are now unused so these have been removed.
Calling if_clone_detach() will now destroy all the cloned interfaces for the
driver and in most cases is all thats needed to unload.
Idea by: brooks
Reviewed by: brooks
- Use curthread for calls to knlist_delete() and add a big comment
explaining why as well as appropriate assertions.
- Use TAILQ_FOREACH and TAILQ_FOREACH_SAFE instead of handrolling them.
- Use fget() family of functions to lookup file objects instead of
grovelling around in file descriptor tables.
- Destroy the aio_freeproc mutex if we are unloaded.
Tested on: i386
-Change unconditional aquisition of Giant to only pickup Giant if the vnode
for the controlling tty resides on a non-mpsafe file system.
-Pickup Giant around executable vnode reference counting operations only if
the executable resides on a non-mpsafe file system.
-If this process is being traced, pickup Giant for trace file reference count
operations only if it resides on a non-mpsafe file system.
Discussed with: jhb
Tested by: kris
the RocketPort unit number in the name of the devices. This means that
unit 0 device names will change from ttyR0 .. ttyRf to ttyR00 .. ttyR0f.
Reviewed by: phk
retransmitted without suppression, while there is demand for
such ARP entry. As before, retransmission is rate limited to
one packet per second. Details:
- Remove net.link.ether.inet.host_down_time
- Do not set/clear RTF_REJECT flag on route, to
avoid rt_check() returning error. We will generate error
ourselves.
- Return EWOULDBLOCK on first arp_maxtries failed
requests , and return EHOSTDOWN/EHOSTUNREACH
on further requests.
- Retransmit ARP request always, independently from return
code. Ratelimit to 1 pps.
For each child process whose status has been changed, a SIGCHLD instance
is queued, if the signal is stilling pending, and process changed status
several times, signal information is updated to reflect latest process
status. If wait() returns because the status of a child process is
available, pending SIGCHLD signal associated with the child process is
discarded. Any other pending SIGCHLD signals remain pending.
The signal information is allocated at the same time when proc structure
is allocated, if process signal queue is fully filled or there is a memory
shortage, it can still send the signal to process.
There is a booting time tunable kern.sigqueue.queue_sigchild which
can control the behavior, setting it to zero disables the SIGCHLD queueing
feature, the tunable will be removed if the function is proved that it is
stable enough.
Tested on: i386 (SMP and UP)
the interface. This allows run-time selection of MMU code, based
on CPU-type detection, or tunable-overrides when testing new code.
Pre-requisite for G5 support.
conf/files.powerpc
- remove pmap.c
- add mmu_if.h, mmu_oea.c, pmap_dispatch.c
powerpc/include/mmuvar.h
- definitions for MMU implementations
powerpc/include/pmap.h
- remove pmap_pte_spill declaration
- add pmap_mmu_install declaration
- size the phys_avail array
- pmap_bootstrapped is now global-scope
powerpc/powerpc/machdep.c
- call kobj_machdep_init early in the boot sequence to allow
kobj usage prior to SI_SUB_LOCK
- install the OEA pmap code. This will be moved to CPU-specific
init code in the future.
powerpc/powerpc/mmu_if.m
- Kobj MMU interface definitions
powerpc/powerpc/pmap_dispatch.c
- central dispatch for pmap calls
- contains the global mmu kobj and the routine to locate the
the mmu implementation and init the kobj
by the zero-copy sockets method, and written to before the transmission
completes, we need to destroy all of the existing mappings to the page,
not just the one that we fault on. Otherwise, the mappings will no longer
be to the same page and changes made through one of the mappings will not
be visible through the others.
Observed by: tegge
acpi_resource change was a minor nit offered as an early candidate for
the recent ACPICA import problem and the acpi.c change is one I need to
test still that makes the ordered probing of system devices actually work
as advertised (probe devices in order based on the type of device rather
than in the order we encounter them in the device tree).
entry that is not zero, assume that it is really a hard-wired IRQ (commonly
used for APIC routing) and not a source index. In practice, we've only
ever seen source indices of 0 for legitimate non-hard-wired _PRT entries.
Reviewed by: njl
Tested by: Alex Lyashkov shadow at psoft dot net
MFC after: 2 weeks
After a number of tests using nop's to change the alignment, it was
confirmed that the mtibat instructions should be cache-aligned.
FreeScale app note AN2540 indicates that the isync before and after
the mtdbat is the right thing to do, but sync/isync isn't required
before the mtibat so it has been removed.
Fix by using a ".balign 32" to pull the code in question to the correct
alignment.
MFC after: 3 days
Intel's web site requires some minor tweaks to get it to work:
- The driver seems to have been released with full WMI tracing enabled,
and makes references to some WMI APIs, namely IoWMIRegistrationControl(),
WmiQueryTraceInformation() and WmiTraceMessage(). Only the first
one is ever called (during intialization). These have been implemented
as do-nothing stubs for now. Also added a definition for STATUS_NOT_FOUND
to ntoskrnl_var.h, which is used as a return code for one of the WMI
routines.
- The driver references KeRaiseIrqlToDpcLevel() and KeLowerIrql()
(the latter as a function, which is unusual because normally
KeLowerIrql() is a macro in the Windows DDK that calls KfLowewIrql()).
I'm not sure why these are being called since they're not really
part of WDM. Presumeably they're being used for backwards
compatibility with old versions of Windows. These have been
implemented in subr_hal.c. (Note that they're _stdcall routines
instead of _fastcall.)
- When querying the OID_802_11_BSSID_LIST OID to get a BSSID list,
you don't know ahead of time how many networks the NIC has found
during scanning, so you're allowed to pass 0 as the list length.
This should cause the driver to return an 'insufficient resources'
error and set the length to indicate how many bytes are actually
needed. However for some reason, the Intel driver does not honor
this convention: if you give it a length of 0, it returns some
other error and doesn't tell you how much space is really needed.
To get around this, if using a length of 0 yields anything besides
the expected error case, we arbitrarily assume a length of 64K.
This is similar to the hack that wpa_supplicant uses when doing
a BSSID list query.
Move what can be moved (UMA zones creation, pv_entry_* initialization) from
pmap_init2() to pmap_init().
Create a new function, pmap_postinit(), called from cpu_startup(), to do the
L1 tables allocation.
pmap_init2() is now empty for arm as well.
sio(4) will claim it. This change therefore only affects how ports
are handled when they are not claimed by sio(4), and in principle
will improve hardware support.
MFC after: 2 months
from there. All others get broken up and free'd individually to the mbuf
and cluster zones.
The packet zone is a secondary zone to the mbuf zone. There is currently
a limitation in UMA which prevents decreasing the packet zone stock when
the mbuf and cluster zone are drained and all their members are part of
packets. When this is fixed this change may be reverted.
- Fix a typo in rsmisc.c and a style change for consistency.
This patch will also appear in future ACPI-CA release.
Submitted by: Robert Moore <robert dot moore at intel dot com>
Tested by: ru
descriptor. This should fix the "memory modified after free" panics. This
patch will appear in a future acpi-ca distribution.
Submitted by: Robert Moore <robert.moore / intel.com>
Tested by: Peter Holm
Previously, pvzone's initialization was split between pmap_init() and
pmap_init2(). This split initialization was the underlying cause of
some UMA panics during initialization. Specifically, if the UMA boot
pages was exhausted before the pvzone was fully initialized, then UMA,
through no fault of its own, would use an inappropriate back-end
allocator leading to a panic. (Previously, as a workaround, we have
increased the UMA boot pages.) Fortunately, there is no longer any
reason that pvzone's initialization cannot be completed in
pmap_init().
Eliminate a check for whether pv_entry_high_water has been initialized
or not from get_pv_entry(). Since pvzone's initialization is
completed in pmap_init(), this check is no longer needed.
Use cnt.v_page_count, the actual count of available physical pages,
instead of vm_page_array_size to compute the maximum number of pv
entries.
Introduce the vm.pmap.pv_entries tunable on alpha and ia64.
Eliminate some unnecessary white space.
Discussed with: tegge (item #1)
Tested by: marcel (ia64)
a synchronous reprogramming of hardware MAC filters if the physical
interface are up and running. Previously, MAC filters would be
reconfigured only when the fec interface was brought up.
- Disallow bundle reconfiguration when virtual
interface is running; otherwise, removing a
port from a running configuration will cause
a panic in the start() method on the next packet
on an assumption that a bundle has an even
number of ports (2 or 4).
- Disallow bringing of virtual interface to a
running state when a bundle size is 0; otherwise,
adding and then removing the port will similarly
cause a panic.
- Add missing initialization of fec_ifstat when
adding a new port and fix media status reporting
when virtual interface isn't yet up (check for
fec_status of 1 rather than != 0).
previously, ifp->if_type was set to IFT_ETHER by
ether_ifattach(), now it's done by if_alloc() so
an assignment of if_type to IFT_PROPVIRTUAL after
if_alloc() but before ether_ifattach() broke it.
This makes arp(8) and friends happy about the fec
interfaces, and will allow us to use if_setlladdr()
on the fec interface.
- Set/reset IFF_DRV_RUNNING/IFF_DRV_OACTIVE in init()
and stop() methods rather than in ioctl(), like the
rest of the drivers do. This fixes a bug when an
"ifconfig fec0 ipv4_address" would not have made
the interface running, didn't launch the ticker
function to track media status of bundled ports,
etc.
used in the base system. This has been much discussed in the past
(typically people giving me a hard time for it). Since all that was
added to config was nocpu, and since we don't use it, we don't need to
bump the version.
current context in the IPI_STOP handler so that we can get accurate stack
traces of threads on other CPUs on these two archs like we do now on i386
and amd64.
Tested on: alpha, sparc64
buffers *and* there are no buffers queued up for writing. The bug
was that NMODIFIED was being cleared even while there were buffers
scheduled to be written out, which leads to all sorts of interesting
bugs - one where the file could shrink (because of a post-op getattr
load, say) causing data in buffer(s) queued for write to be tossed,
resulting in data corruption.
Submitted by: Mohan Srinivasan
both proc pointer and thread pointer, if thread pointer is NULL,
tdsignal automatically finds a thread, otherwise it sends signal
to given thread.
Add utility function psignal_event to send a realtime sigevent
to a process according to the delivery requirement specified in
struct sigevent.
source is first enabled similar to how intr_event's now allocate ithreads
on-demand. Previously, we would map IDT vectors 1:1 to IRQs. Since we
only have 191 available IDT vectors for I/O interrupts, this limited us
to only supporting IRQs 0-190 corresponding to the first 190 I/O APIC
intpins. On many machines, however, each PCI-X bus has its own APIC even
though it only has 1 or 2 devices, thus, we were reserving between 24 and
32 IRQs just for 1 or 2 devices and thus 24 or 32 IDT vectors. With this
change, a machine with 100 IRQs but only 5 in use will only use up 5 IDT
vectors. Also, this change provides an API (apic_alloc_vector() and
apic_free_vector()) that will allow a future MSI interrupt source driver to
request IDT vectors for use by MSI interrupts on x86 machines.
Tested on: amd64, i386
for code to start out on one CPU when thunking into Windows
mode in ctxsw_utow(), and then be pre-empted and migrated to another
CPU before thunking back to UNIX mode in ctxsw_wtou(). This is
bad, because then we can end up looking at the wrong 'thread environment
block' when trying to come back to UNIX mode. To avoid this, we now
pin ourselves to the current CPU when thunking into Windows code.
Few other cleanups, since I'm here:
- Get rid of the ndis_isr(), ndis_enable_interrupt() and
ndis_disable_interrupt() wrappers from kern_ndis.c and just invoke
the miniport's methods directly in the interrupt handling routines
in subr_ndis.c. We may as well lose the function call overhead,
since we don't need to export these things outside of ndis.ko
now anyway.
- Remove call to ndis_enable_interrupt() from ndis_init() in if_ndis.c.
We don't need to do it there anyway (the miniport init routine handles
it, if needed).
- Fix the logic in NdisWriteErrorLogEntry() a little.
- Change some NDIS_STATUS_xxx codes in subr_ntoskrnl.c into STATUS_xxx
codes.
- Handle kthread_create() failure correctly in PsCreateSystemThread().
based jumbo 9k and jumbo 16k cluster support.
All mbuf's with external storage attached are mandatory reference
counted. For clusters and jumbo clusters UMA provides the refcnt
storage directly. It does not have to be separatly allocated. Any
other type of external storage gets its own refcnt allocated from
an UMA mbuf refcnt zone instead of normal kernel malloc.
The refcount API MEXT_ADD_REF() and MEXT_REM_REF() is no longer
publically accessible. The proper m_* functions have to be used.
mb_ctor_clust() and mb_dtor_clust() both handle normal 2K as well
as 9k and 16k clusters.
Clusters and jumbo clusters may be obtained without attaching it
immideatly to an mbuf. This is for high performance cluster
allocation in network drivers where mbufs are attached after the
cluster has been filled.
Tested by: rwatson
Sponsored by: TCP/IP Optimizations Fundraise 2005
destruction:
- Backout 1.62, since it doesn't fix all possible
problems.
- Upon node creation, put an additional reference on node.
- Add a mutex and refcounter to struct ngsock. Netgraph node,
control socket and data socket all count as references.
- Introduce ng_socket_free_priv() which removes one reference
from ngsock, and frees it when all references has gone.
- No direct pointers between pcbs and node, all pointing
is done via struct ngsock and protected with mutex.
- Introduce ng_topo_mtx, a mutex to protect topology changes.
- In ng_destroy_node() protect with ng_topo_mtx the process
of checking and pointing at ng_deadnode. [1]
- In ng_con_part2() check that our peer is not a ng_deadnode,
and protect the check with ng_topo_mtx.
- Add KASSERTs to ng_acquire_read/write, to make more
understandible synopsis in case if called on ng_deadnode.
Reported by: Roselyn Lee [1]
- Introduce a new flags NGQF_QREADER and NGQF_QWRITER,
which tell how the item should be actually applied,
overriding NGQF_READER/NGQF_WRITER flags.
- Do not differ between pending reader or writer. Use only
one flag that is raised, when there are pending items.
- Schedule netgraph ISR in ng_queue_rw(), so that callers
do not need to do this job.
- Fix several comments.
Submitted by: julian
Having an additional MT_HEADER mbuf type is superfluous and redundant
as nothing depends on it. It only adds a layer of confusion. The
distinction between header mbuf's and data mbuf's is solely done
through the m->m_flags M_PKTHDR flag.
Non-native code is not changed in this commit. For compatibility
MT_HEADER is mapped to MT_DATA.
Sponsored by: TCP/IP Optimization Fundraise 2005
ktr_tid as part of gathering of ktr header data for new ktrace
records. The continued use of intptr_t is required for file layout
reasons, and cannot be changed to lwpid_t at this point.
MFC after: 1 month
Reviewed by: davidxu
intptr_t. The buffer length needs to be written to disk as part
of the trace log, but the kernel pointer for the buffer does not.
Add a new ktr_buffer pointer to the kernel-only ktrace request
structure to hold that pointer. This frees up an integer in the
ktrace record format that can be used to hold the threadid,
although older ktrace files will have a garbage ktr_buffer field
(or more accurately, a kernel pointer value).
MFC after: 2 weeks
Space requested by: davidxu
If a copy-on-write fault occurs on the page, the new copy should inherit
a part of the original page's wire count.
Submitted by: tegge
MFC after: 1 week
fails, reclaim a pv entry by destroying a mapping to an inactive
page.
Change the format strings in many of the assertions that were recently
converted from PMAP_DIAGNOSTIC printf()s so that they are compatible
with PAE. Avoid unnecessary differences between the amd64 and i386
format strings.
since the link takes a bit to negotiate, the information is pretty
much never available during the probe. As such, the boot output
pretty much always prints N/A for speed and duplex. Since we print
out the output of ifconfig during the user space boot, this early
boot information is also generally redundant, and added to the noise.
MFC after: 2 weeks
before dereferencing it. Certain corrupt kernel modules might not have
a valid hash table, and would cause a kernel panic when they were loaded.
Instead of panic'ing, the kernel now prints out a warning that it is
missing the symbol hash table.
Tested by: Benjamin Close Benjamin dot Close at clearchain dot com
MFC after: 1 week
PCI-ISA bridge. Thus, when viapm0 or viapropm0 attaches, isab0 dosen't
attach so there is no isa0 bus hung off of that bridge. In the non-ACPI
case, legacy0 will add an isa0 anyway as a fail-safe, but ACPI assumes that
any ISA bus will be enumerated via a bridge. To fix this, call
isab_attach() to attach an isa0 ISA child bus device if the pm or propm
device we are probing is a PCI-ISA bridge. Both drivers now have to
implement the bus_if interface via the generic methods for resource
allocation, etc. to work. Also, we now add 2 new ISA bus drivers that
attach to viapm and viapropm devices.
PR: kern/87363
Reported by: Oliver Fromme olli at secnetix dot de
Tested by: glebius
MFC after: 1 week
- Prefer '_' to ' ', as it results in more easily parsed results in
memory monitoring tools such as vmstat.
- Remove punctuation that is incompatible with using memory type names
as file names, such as '/' characters.
- Disambiguate some collisions by adding subsystem prefixes to some
memory types.
- Generally prefer lower case to upper case.
- If the same type is defined in multiple architecture directories,
attempt to use the same name in additional cases.
Not all instances were caught in this change, so more work is required to
finish this conversion. Similar changes are required for UMA zone names.
in bytes to start off with. This caused the GPT geom sniffer to attempt
a seek just back from the end of the 'disk', which resulted in a > 4G
seek, causing gdb psim to exit since it only supports 32-bit seeks.
The size of the disk should really be specified in the psim device tree,
but for now do the minimal amount of work to get psim to run again.
aac_alloc_sync_fib(). aac_alloc_sync_fib() will assert that the I/O locks
are held. This fixes a panic on system boot up when the aac(4) device's
bus_generic_attach() routine is called.
Reviewed by: scottl
OpenFirmware. FreeBSD/ppc uses SPRG0 as the per-cpu data area pointer,
and SPRG1-3 as temporary registers during exception handling. There
have been a few instances where OpenFirmware does require these to
be part of it's context, such as cd-booting an eMac.
reported by: many
MFC after: 3 days
following the protocol pru_listen() call to solisten_proto(), so
that it occurs under the socket lock acquisition that also sets
SO_ACCEPTCONN. This requires passing the new backlog parameter
to the protocol, which also allows the protocol to be aware of
changes in queue limit should it wish to do something about the
new queue limit. This continues a move towards the socket layer
acting as a library for the protocol.
Bump __FreeBSD_version due to a change in the in-kernel protocol
interface. This change has been tested with IPv4 and UNIX domain
sockets, but not other protocols.
that caused a premature exit after calling a fast interrupt handler
and bypassing a much needed critical_exit() and the scheduling of
the interrupt thread for non-fast handlers. In short: unbreak :-)
- Return EINVAL if play_format or rec_format is set but the corresponding
sample rate is 0.
- Don't try to set the playback or recording format to 0. Previously,
issuing an AIOSFMT ioctl with an all-zeroes snd_chan_param would
trigger a KASSERT in chn_fmtchain(); I'm unsure about the effects on
a kernel without INVARIANTS. After this commit, issuing AIOSFMT with
an all-zeroes snd_chan_param is equivalent to issuing AIOGFMT.
MFC after: 2 weeks
trying to access user-space stack addresses when a user fault
is encountered, as occurs when GEOM KTR code is handling a page fault
and is using stack_save() to capture a trace for debug purposes.
It may be possible to walk beyond the trap-frame if it is a kernel fault,
as db_backtrace() does, but I don't think that complexity is needed in
this routine.
MFC after: 3 days
convert to or from timeval frequently.
Introduce function itimer_accept() to ack a timer signal in signal
acceptance code, this allows us to return more fresh overrun counter
than at signal generating time. while POSIX says:
"the value returned by timer_getoverrun() shall apply to the most
recent expiration signal delivery or acceptance for the timer,.."
I prefer returning it at acceptance time.
Introduce SIGEV_THREAD_ID notification mode, it is used by thread
libary to request kernel to deliver signal to a specified thread,
and in turn, the thread library may use the mechanism to implement
SIGEV_THREAD which is required by POSIX.
Timer signal is managed by timer code, so it can not fail even if
signal queue is full filled by sigqueue syscall.
actual resource values we received from the system rather than the range
we requested. Since we request a range starting at 0, we would record
that number. Later, since this == 0, we'd allocate again. However,
we wouldn't write the new resource into the BAR. This resulted in
a resource leak as well as a BAR that couldn't access the resource at
all since rman_get_start, et al, were wrong.
MFC After: 1 week (assuming RELENG_6 is open for business)
