- add identify method to create driver's own device_t
- successfully probe only driver's own device_t instead of any device_t
- (ab)use device order to hopefully be probed/attached after acpi_wmi
PR: kern/147858
Tested by: Maciej Suszko <maciej@suszko.eu>
MFC after: 1 week
- Add special check for case when time expires before being programmed.
This fixes interrupt loss and respectively timer death on attempt to
program very short interval. Increase minimal supported period to more
realistic value.
- Add support for hint.hpet.X.allowed_irqs tunable, allowing manually
specify which interrupts driver allowed to use. Unluckily, many BIOSes
program wrong allowed interrupts mask, so driver tries to stay on safe
side by not using unshareable ISA IRQs. This option gives control over
this limitation, allowing more per-CPU timers to be provided, when FSB
interrupts are not supported. Value of this tunable is bitmask.
- Do not use regular interrupts on virtual machines. QEMU and VirtualBox
do not support them properly, that may cause problems. Stay safe by default.
Same time both QEMU and VirtualBox work fine in legacy_route mode.
VirtualBox also works fine if manually specify allowed ISA IRQs with above.
Both deadline and current_time are time_seconds (+ utc_offset())
casted to unsigned long long. No need to cast to or print as pointers.
MFC after: 4 days
to pad with 0xFF when it encounter short frames. According to RFC
1042 the pad bytes should be 0x00.
Because manual padding consumes extra CPU cycles, introduce a new
tunable which controls the padding behavior. Turning this tunable
on will have driver pad manually but it's disabled by default. Users
can enable software padding by setting the following tunable to
non-zero value.
dev.sis.%d.manual_pad="1"
PR: kern/35422 (patch not used)
prevented driver from working on big-endian machines. Also rewrite
station address programming to make it work on strict-alignment
architectures. With this change, sis(4) now works on sparc64 and
performance number looks good even though sis(4) have to apply
fixup code to align received frames on 2 bytes boundary on sparc64.
response to DMA activate FIS under certain circumstances. This is
recommended fix from chip datasheet. If triggered, this bug most likely
cause write command timeout.
MFC after: 2 weeks
value 0xff. On hot-plug this value confuses ata_generic_reset() device
presence detection logic. As soon as we already know drive presence from
SATA hard reset, hint ata_generic_reset() to wait for device signature
until success or full timeout.
greater than 65535 bytes then the CDC driver might not work as expected, which
is not likely with the existing USB speeds.
Submitted by: Hans Petter Selasky
allmulti is toggled. Controller does not require reinitialization.
This removes unnecessary controller reinitialization whenever
tcpdump is used.
While I'm here remove unnecessary variable reinitialization.
configured TX/RX MACs before getting a valid link. After that, when
link state change callback is called, it called device
initialization again to reconfigure TX/RX MACs depending on
resolved link state. This hack created several bad side effects and
it required more hacks to not collide with sis_tick callback as
well as disabling switching to currently selected media in device
initialization. Also it seems sis(4) was used to be a template
driver for long time so other drivers which was modeled after
sis(4) also should be changed.
TX/RX MACs are now reconfigured after getting a valid link. Fix for
short cable error is also applied after getting a link because it's
only valid when the resolved speed is 100Mbps.
While I'm here slightly reorganize interrupt handler such that
sis(4) always read SIS_ISR register to see whether the interrupt is
ours or not. This change removes another hack and make it possible
to nuke sis_stopped variable in softc.
o Enforce TX/RX descriptor ring alignment. NS data sheet says the
controller needs 4 bytes alignment but use 16 to cover both SiS
and NS controllers. I don't have SiS data sheet so I'm not sure
what is alignment restriction of SiS controller but 16 would be
enough because it's larger than the size of a TX/RX descriptor.
Previously sis(4) ignored the alignment restriction.
o Enforce RX buffer alignment, 4.
Previously sis(4) ignored RX buffer alignment restriction.
o Limit number of TX DMA segment to be used to 16. It seems
controller has no restriction on number of DMA segments but
using more than 16 looks resource waste.
o Collapse long mbuf chains with m_collapse(9) instead of calling
expensive m_defrag(9).
o TX/RX side bus_dmamap_load_mbuf_sg(9) support and remove
unnecessary callbacks.
o Initial endianness support.
o Prefer local alignment fixup code to m_devget(9).
o Pre-allocate TX/RX mbuf DMA maps instead of creating/destroying
these maps in fast TX/RX path. On non-x86 architectures, this is
very expensive operation and there is no need to do that.
o Add missing bus_dmamap_sync(9) in TX/RX path.
o watchdog is now unarmed only when there are no pending frames
on controller. Previously sis(4) blindly unarmed watchdog
without checking the number of queued frames.
o For efficiency, loaded DMA map is reused for error frames.
o DMA map loading failure is now gracefully handled. Previously
sis(4) ignored any DMA map loading errors.
o Nuke unused macros which are not appropriate for endianness
operation.
o Stop embedding driver maintained structures into descriptor
rings. Because TX/RX descriptor structures are shared between
host and controller, frequent bus_dmamap_sync(9) operations are
required in fast path. Embedding driver structures will increase
the size of DMA map which in turn will slow down performance.
not change interrupt vector if it is not pointing the ROM itself. Actually,
we just fail shadowing altogether if that is the case because the shadowed
copy will be useless for sure and POST may not be relocatable or useful.
While I'm here, fix a debugging message under bootverbose, really. r211829
fixed one case but broke another. Mea Culpa.
or not by comparing reported TX consumer index with saved index. So
remove unnecessary check done after freeing transmitted mbufs.
While I'm here nuke unnecessary variable initializations.
tag. All controllers that are not BCM5755 or higher have 4GB
boundary DMA bug. Previously bge(4) used 32bit DMA address to
workaround the bug(r199670). However this caused the use of bounce
buffers such that it resulted in poor performance for systems which
have more than 4GB memory. Because bus_dma(9) honors boundary
restriction requirement of DMA tag for dynamic buffers, having a
separate TX/RX mbuf DMA tag will greatly reduce the possibility of
using bounce buffers. For DMA buffers allocated with
bus_dmamem_alloc(9), now bge(4) explicitly checks whether the
requested memory region crossed the boundary or not.
With this change, only the DMA buffer that crossed the boundary
will use 32bit DMA address. Other DMA buffers are not affected as
separate DMA tag is created for each DMA buffer.
Even if 32bit DMA address space is used for a buffer, the chance to
use bounce buffer is still very low as the size of buffer is small.
This change should eliminate most usage of bounce buffers on
systems that have more than 4GB memory.
More correct fix would be teaching bus_dma(9) to honor boundary
restriction for buffers created with bus_dmamem_alloc(9) but it
seems that is not easy.
While I'm here cleanup bge_dma_map_addr() and remove unnecessary
member variables in bge_dmamap_arg structure.
Tested by: marcel
heavy I/O load.
Many thanks to LSI for continuing to support FreeBSD.
PR: kern/149968
Submitted by: LSI (Tom Couch)
Reported by: Kai Kockro <kkockro web de>
Tested by: Kai Kockro, jpaetzel
MFC after: 7 days
configuration function. For failed memory allocations, em(4)/lem(4)
called panic(9) which is not acceptable on production box.
igb(4)/ixgb(4)/ix(4) allocated the required memory in stack which
consumed 768 bytes of stack memory which looks too big.
To address these issues, allocate multicast array memory in device
attach time and make multicast configuration success under any
conditions. This change also removes the excessive use of memory in
stack.
Reviewed by: jfv
Just showing some buffer allocation error is more appropriate
action for drivers. This should fix occasional panic reported on
em(4) when driver encountered resource shortage.
Reviewed by: jfv
supported by many BIOSes to improve performance of VESA BIOS calls for real
mode OSes but it is not our intention here. However, this may help some
platforms where the video ROMs are inaccessible after suspend, for example.
Note it may consume up to 64K bytes of contiguous memory depending on video
controller model when it is enabled. This feature can be disabled by
setting zero to 'debug.vesa.shadow_rom' loader tunable via loader(8) or
loader.conf(5). The default is 1 (enabled), for now.
ID, plus the ability to force '16-bit mode' which really means NE-2000
mode. Other open source drivers suggest that the Holtek misbehaves if
you allow the 8-bit probe. Also, all of the PCI chips emulate
NE-2000ish cards, so always force 16-bit mode for memory transfers.
PR: 84202 (patch not used)
I'm not sure whether adding this logical id is correct or not
because Compex RL2000 is in the list of supported hardware list.
I guess the Compex RL2000 could be PCI variant while the controller
in question is ISA controller. It seems PNP compat id didn't match
or it had multiple compat ids so isa_pnp_probe() seemed to return
ENOENT.
PR: kern/80853
support WOL. Some controllers require additional 3-wire auxiliary
remote wakeup connector to draw power. More recent xl(4)
controllers may not need the wakeup connector though.
initialize controller from a known good state. Previously driver
used to issue controller reset while TX/RX DMA are in progress.
I guess resetting controller in active TX/RX DMA cycle is to ensure
stopping I/Os in xl_shutdown(). I remember some buggy controllers
didn't respond with stop command if controller is under high
network load at the time of shutdown so resetting controller was
the only safe way to stop the I/Os. However, from my experiments,
controller always responded with stop command under high network
load so I think it's okay to remove the xl_reset() in
device_shutdown handler.
Resetting controller also will clear configured RX filter which
in turn will make WOL support hard because driver have to reprogram
RX filter in WOL handler as well as setting station address.
datagrams with checksum value 0 when TX UDP checksum offloading is
enabled. Generating UDP checksum value 0 is RFC 768 violation.
Even though the probability of generating such UDP datagrams is
low, I don't want to see FreeBSD boxes to inject such datagrams
into network so disable UDP checksum offloading by default. Users
still override this behavior by setting a sysctl variable or loader
tunable, dev.bge.%d.forced_udpcsum.
I have no idea why this issue was not reported so far given that
bge(4) is one of the most commonly used controller on high-end
server class systems. Thanks to andre@ who passed the PR to me.
PR: kern/104826
Makefiles or *.mk files, use ${CC:T:Mfoo} instead, so only the basename
of the compiler command (excluding any arguments) is considered.
This allows you to use, for example, CC="/nondefault/path/clang -xxx",
and still have the various tests in bsd.*.mk identify your compiler as
clang correctly.
ICC if cases were also changed.
Submitted by: Dimitry Andric <dimitry at andric.com>
method is used by the PCI bus driver to query the power management system
to determine the proper device state to be used for a device during suspend
and resume. For the ACPI PCI bridge drivers this calls
acpi_device_pwr_for_sleep(). This removes ACPI-specific knowledge from
the PCI and PCI-PCI bridge drivers.
Reviewed by: jkim
If it does, don't then try reprogramming the NF "cap" values (ie
what values are the "maximum" value the NF can be) - instead,
just leave the current CCA value as the NF cap.
This was inspired by some similar work from ath9k. It isn't
a 100% complete solution (as there may be some reason where a
high NF CCA/cap is written, causing the baseband to stop thinking it
is able to transmit, leading to stuck beacon and interface reset)
which I'll investigate and look at fixing in a later commit.
Obtained from: Linux
AR5416 and later chipsets.
ath_hal_calibrateN() calls the HAL calibrateN function with rxchainmask=0x1.
This is not necessarily the case for AR5416 and later chipsets.
list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
flag immediately so it's only set once per longcal interval.
Without this, the current AR5416 code will continuously spam NF
calibrations during a periodic calibration if the longcal flag
is set. The longcal flag wouldn't be cleared until the calibration
method indicates that calibrations are "complete".
This drops the rate of NF calibration updates down from "once every
shortcal" (ie, every 100ms) during a periodic calibration, to only
once per "longcal" interval. Spamming NF calibrations every 100ms
caused some potentially horrific issues in noisy environments as
NF calibrations can take longer than 100ms and this spamming can
cause invalid NF calibration results to be read back - leading to
missed beacons, and thus leading to a stuck beacon situation.
Stuck beacons cause interface resets, which restart calibrations.
This means that the longcal calibration runs every 100ms (shortcal)
until all initial calibrations are completed. This spamming can then
cause the above issues which leads to stuck beacons, leading to
interface resets, etc, etc. Quite annoying.
