the ORDERED tag. This recoups significant performance gains for many
arrays.
The default is still to send out the ORDERED tag periodically.
Reviewed by: scsi (justin+timeout)
KERNCONF after the file has been copied to the sys/${ARCH}/conf directory. This
allows the use of one kernel config file for multiple images. E.g.:
NANO_KERNEL=../../../../software/nanobsd/default/SOEKRIS
MFC: after 6.2
to do the userland to kernel copying in sosend_generic() and sosend_dgram().
sosend_copyin() is retained for ZERO_COPY_SOCKETS which are not yet supported
by m_uiotombuf().
Benchmaring shows significant improvements (95% confidence):
66% less cpu (or 2.9 times better) with new sosend vs. old sosend (non-TSO)
65% less cpu (or 2.8 times better) with new sosend vs. old sosend (TSO)
(Sender AMD Opteron 852 (2.6GHz) with em(4) PCI-X-133 interface and receiver
DELL Poweredge SC1425 P-IV Xeon 3.2GHz with em(4) LOM connected back to back
at 1000Base-TX full duplex.)
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 month
mbuf clusters. Add a flags parameter to accept M_PKTHDR and M_EOR mbuf
chain flags. Provide compatibility macro for m_getm() calling m_getm2()
with M_PKTHDR set.
Rewrite m_uiotombuf() to use m_getm2() for mbuf allocation and do the
uiomove() in a tight loop over the mbuf chain. Add a flags parameter to
accept mbuf flags to be passed to m_getm2(). Adjust all callers for the
extra parameter.
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 month
to get the physical address doesn't work for all values of KVA_PAGES,
while masking 8 MSBs works for all values of KVA_PAGES that are
multiple of 4 for non-PAE and 8 for PAE. (This leaves us limited
with 12MB for non-PAE kernels and 14MB for PAE kernels.)
To get things right, we'd need to subtract the KERNBASE from the
virtual address (but KERNBASE is not easy to figure out from here),
or have physical addresses set properly in the ELF headers.
Discussed with: jhb
VM pages into mbufs as it can -- up to the free send socket buffer space.
The outer loop then drops the whole mbuf chain into the send socket buffer,
calls tcp_output() on it and then waits until 50% of the socket buffer are
free again to repeat the cycle. This way tcp_output() gets the full amount
of data to work with and can issue up to 64K sends for TSO to chop up in
the network adapter without using any CPU cycles. Thus it gets very efficient
especially with the readahead the VM and I/O system do.
The previous sendfile(2) code simply looped over the file, turned each 4K
page into an mbuf and sent it off. This had the effect that TSO could only
generate 2 packets per send instead of up to 44 at its maximum of 64K.
Add experimental SF_MNOWAIT flag to sendfile(2) to return ENOMEM instead of
sleeping on mbuf allocation failures.
Benchmarking shows significant improvements (95% confidence):
45% less cpu (or 1.81 times better) with new sendfile vs. old sendfile (non-TSO)
83% less cpu (or 5.7 times better) with new sendfile vs. old sendfile (TSO)
(Sender AMD Opteron 852 (2.6GHz) with em(4) PCI-X-133 interface and receiver
DELL Poweredge SC1425 P-IV Xeon 3.2GHz with em(4) LOM connected back to back
at 1000Base-TX full duplex.)
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 month
longjmp to the default context. As result, "alltrace" command may
be prematurely terminated (without error message). This is happens,
for instance, when system is low on memory and referenced page in
kernel-mode thread stack is swapped out.
Protect "alltrace" against termination on trap by setting temporary
kdb_jmpbuf context.
Submitted by: Peter Holm
device (kind) specific unit field to the common field. This change
allows a future version of libefi to work without requiring anything
more than what is defined in struct devdesc and as such makes it
possible to compile said version of libefi for different platforms
without requiring that those platforms have identical derivatives
of struct devdesc.
as we have no use for that info. Instead let this function return the
keyboard ID and verify at its invocation in sunkbd_configure() that we're
talking to a Sun type 4/5/6 keyboard, i.e. a keyboard supported by this
driver.
- Add an option SUNKBD_EMULATE_ATKBD whose code is based on the respective
code in ukbd(4) and like UKBD_EMULATE_ATSCANCODE causes this driver to
emit AT keyboard/KB_101 compatible scan codes in K_RAW mode as assumed by
kbdmux(4). Unlike UKBD_EMULATE_ATSCANCODE, SUNKBD_EMULATE_ATKBD also
triggers the use of AT keyboard maps and thus allows to use the map files
in share/syscons/keymaps with this driver at the cost of an additional
translation (in ukbd(4) this just is the way of operation).
- Implement an option SUNKBD_DFLT_KEYMAP, which like the equivalent options
of the other keyboard drivers allows to specify the default in-kernel
keyboard map. For obvious reasons this made to only work when also using
SUNKBD_EMULATE_ATKBD.
- Implement sunkbd_check(), sunkbd_check_char() and sunkbd_clear_state(),
which are also required for interoperability with kbdmux(4).
- Implement K_CODE mode and FreeBSD keypad compose.
- As a minor hack define KBD_DFLT_KEYMAP also in the !SUNKBD_EMULATE_ATKBD
case so we can obtain fkey_tab from <dev/kbd/kbdtables.h> rather than
having to duplicate it and #ifdef some more code.
- Don't use the TX-buffer for writing the two command bytes for setting the
keyboard LEDs as this consequently requires a hardware FIFO that is at
least two bytes in depth, which the NMOS-variant of the Zilog SCCs doesn't
have. Thus use an inlined version of uart_putc() to consecutively write
the command bytes (a cleaner approach would be to do this via the soft
interrupt handler but that variant wouldn't work while in ddb(4)). [1]
- Fix some minor style(9) bugs.
PR: 90316 [1]
Reviewed by: marcel [1]
gmirror and graid3 in a way that it is not resynchronized after a
power failure or system crash.
It is safe when gjournal is running on top of gmirror/graid3.
BIO_READ/BIO_WRITE is sent to vnode-backed provider (BIO_DELETE or
BIO_FLUSH).
Reported by: ceri
Add support for BIO_FLUSH to vnode-backed md(4) devices based on
VOP_FSYNC().
