calls. Also add BUS_DMA_COHERENT flag to bus_dmamem_alloc(9) to
take advantage of efficient synchronization for architectures that
support that feature.
Reviewed by: davidch
return code. If context was not setup correctly give up
initialization. While I'm here move variable declarations to the
beginning of the function.
Reviewed by: davidch
- Print device details only when verbose boot is enabled.
- Add debug output for shared memory access.
- Add debug statistics (checksum offload & VLAN frame counters).
- Modify TX path to update consumer index for each frame completed
rather than updating the consumer index only once for a group of
frames to improve small packet performance.
- Print driver/firmware pulse messages only when verbose boot
is enabled.
- Add debug sysctl to clear statistics.
- Fix more style(9) violations.
MFC after: 2 weeks
- Added some new debug helper routines to systcl.
- Fixed many of the style(9) violations that have crept into the code
due to my use of a "smart" editor.
MFC after: 2 weeks
parsing code in TSO path as the controller requires VLAN hardware
tagging to make TSO work over VLANs.
While parsing the mbuf in TSO patch, always perform check for
writable mbuf as bce(4) have to reset IP length and IP checksum
field of IP header and make sure to ensure contiguous buffer before
accessing IP/TCP headers. While I'm here replace magic number 40 to
more readable sizeof(struct ip) + sizeof(struct tcphdr).
Reviewed by: davidch
TX/RX checksum handler to set/clear relavant assist bits which was
used to cause unexpected results.
With this change, bce(4) can be bridged with other interfaces that
lack TSO, VLAN checksum offloading.
Reviewed by: davidch
around. Management firmware(ASF/IPMI/UMP) requires the VLAN
hardware tag stripping so don't actually disable VLAN hardware tag
stripping. If VLAN hardware tag stripping was disabled, bce(4)
manually reconstruct VLAN frame by appending stripped VLAN tag.
Also remove unnecessary IFCAP_VLAN_MTU message.
Reviewed by: davidch
frames to be accepted while the driver is resetting the hardware.
This failure is generally observed when broadcast frames are received
during driver load and will generate "Unable to write CTX memory"
errors.
- Small changes to driver flags display.
splitting in bce(4) instead of (ab)using ZERO_COPY_SOCKETS that was not
propagated into if_bce.c anyway. It is disabled by default.
Approved by: davidch
MFC after: 3 days
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
- In bce_rx_intr(), use BUS_DMASYNC_POSTREAD instead of
BUS_DMASYNC_POSTWRITE, as we want to "read" from the
rx page chain pages.
- Document why we need to do PREWRITE after we have updated
the rx page chain pages.
- In bce_intr(), use BUS_DMASYNC_POSTREAD and
BUS_DMASYNC_PREREAD when before and after CPU "reading"
the status block.
- Adjust some nearby style mismatches/etc.
Pointed out by: yongari
Approved by: davidch (no objection) but bugs are mine :)
- Added missing firmware for 5709 A1 controllers.
- Changed some debug statistic variable names to be more consistent.
Submitted by: davidch
MFC after: Two weeks
a real packet error but simply indicate that an unexpected unicast or multicast
error was received by the NIC, which was not counted in the past as well.
Reported by: many (on -stable@)
Reviewed by: davidch
MFC after: 3 days
change. As a side effect, this makes the excessive interrupts to
disappear which has been observed as a regression in recent stable/7.
Reported by: many (on -stable@)
Reviewed by: davidch
- Added some additional code for debug builds.
- Fixed a problem printing physical memory on 64bit system during debugging.
- Modified some of the context memory and mailbox register names to more
clearly distinguish their use.
- Added memory barriers for Intel CPUs when accessing host memory data
structures which are written by hardware.
MFC after: Two weeks.
- Fixed a problem on i386 architecture when using split header/jumbo frame
firmware caused by hardware alignment requirements.
- Added #define BCE_USE_SPLIT_HEADER to allow the feature to be enabled/
disabled. Enabled by default.
PR: kern/123696
MFC after: 2 weeks
aligned on an 8 byte boundary. Prior to rev 1.36 this wasn't a problem
because mbuf clusters tend be naturally aligned. The switch to using
split buffers with the first buffer being the embedded data area of the
mbuf has broken this assumption, at least on i386, causing a complete
failure of RX functionality. Fix this for now by using a full cluster for
the first RX buffer. A more sophisticated approach could be done with the
old buffer scheme to realign the m_data pointer with m_adj(), but I'm also
not clear on performance benefits of this old scheme or the performance
implications of adding an m_adj() call to every allocation.
TX traffic to sit in the send chain until a received packet kick
started the interrupt handler. This would cause extremely slow
performance when used with NFS over UDP.
- Removed untested polling code.
- Updated copyright year in the file header.
- Removed inadvertent ^M's created by DOS text editor.
MFC after: 2 weeks
- Added loose RX MTU functionality to allow frames larger than 1500 bytes
to be accepted even though the interface MTU is set to 1500.
- Implemented new TCP header splitting/jumbo frame support which uses
two chains for receive traffic rather than the original single recevie
chain.
- Added additional debug support code.
errors (especially when jumbo frames are enabled or in low memory systems)
because the RX chain was corrupted when an mbuf was mapped to an unexpected
number of buffers.
- Fixed a problem that would cause kernel panics when an excessively
fragmented TX mbuf couldn't be defragmented and was released by
bce_tx_encap().
Approved by: re(hrs)
MFC after: 7 days
- Updated firmware to latest release (v3.4.8) to fix TSO + jumbo frame lockup
- Added MSI (hw.bce.msi_enable) and TSO (hw.bce.tso_enable) sysctls
- Fixed kernel panic when MSI is used and module is unloaded
- Added several new debug routines
- Removed slack space for RX/TX chains since it only covers sloppy coding
- Fixed a potential problem when programming jumbo MTU size in hardware
- Various other comment changes
MFC after: 4 weeks
