boot problems..
However this demands that dangerously dedicated disks use an
offset of at least 10 from the start to not overwrite the
raid config sector on the HPT...
This is due to a bug that has been in there since Warneer did the
PCCARD stuff, the altioaddr is not offset 8 its offset 14 from
the base address.
Also only probe the master device, no known PCCARD ATA thingies
has a slave AFAIK..
<sys/proc.h> to <sys/systm.h>.
Correctly document the #includes needed in the manpage.
Add one now needed #include of <sys/systm.h>.
Remove the consequent 48 unused #includes of <sys/proc.h>.
write caching is disabled on both SCSI and IDE disks where large
memory dumps could take up to an hour to complete.
Taking an i386 scsi based system with 512MB of ram and timing (in
seconds) how long it took to complete a dump, the following results
were obtained:
Before: After:
WCE TIME WCE TIME
------------------ ------------------
1 141.820972 1 15.600111
0 797.265072 0 65.480465
Obtained from: Yahoo!
Reviewed by: peter
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.
Submitted by: dfr
Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets.
Fix the "resource already allocated" panic with the CMD and other
braindead controllers.
Add options ATA_ENABLE_TAGS, without this option tagged queuing will
not be attempted.
IBM's DPTA and DTLA series of drives (no other disk vendors are known
to support this) on non-Promise controllers (promise controllers lockup
when given the tagged queuing specific commands).
It gives especially master/slave comboes about 5% better performance.
Add support for the Promise ATA100 OEM chip (pdc20265)
Add support for the Cyrix 5530
Change the way status is read from the drives, use the alternate
status reg when possible.
Better support for DEVFS, the acdXtY devices are now created when needed.
Lots of little cleanups.
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
some of the fake devices sometimes seen on single device ATA
channels.
Proberly fail on failures in ata-disk.c, retry instead of hang.
Cleanup the VIA probe/init code a bit.
Fix a couble of missing free's in atapi-cd.c in the changer code.
This is done by misusing the device minor a bit to encode the
track no there.
So to read track #4 just use /dev/acdNt4 where N is the device #.
The driver no automatically sets the blocksize (sectorsize) to
what the track is set to in the TOC.
This has the nice effect that you can now rip audioi tracks
by simply doing:
dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352
it cant be much simpler than that :)
NOTE: the original acdNa & acdNc device still work as usual,
except the blocksize is set according to track0.
Promise Ultra100 / Fasttrak100
HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100)
Intel ICH2 (Intel 815E based motherboards)
So far I can read >90MB/s on the Promise and the HPT370.
I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems
writing is still done in ATA66 mode :(
The ICH2 support is untested as of yet...
need this RSN.
Remove a pointless warning in the root device locating code.
Remove the "wd" compatibility name from the "ad" driver.
WARNING: If you have not updated to use /dev/wd* in your /etc/fstab
and modern bootblocks, it would be a very good idea to do so BEFORE
you upgrade your kernel.
Make the error recovery code a little more obvious.
Inform the user if UDMA66 mode couldn't be selected due to a
non ATA66 compliant 80pin cable.
Minor cosmetics.
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
that fails to proberly close the disk.
The problem seems to be that the HP burners sometimes return
ready when they actually are not, the solution is to not use
immediate mode on the closing commands. This is suboptimal
for real burners, in that they now hog the ATA bus for possibly
minutes, where its really not nessesary, *sigh*.
in struct bio. Eventually, bio_offset will probably obsolete the
bio_blkno and bio_pblkno fields.
Remove the special hack in atapi-cd.c to determine of bio_offset was valid.
Exceptions:
Vinum untouched. This means that it cannot be compiled.
Greg Lehey is on the case.
CCD not converted yet, casts to struct buf (still safe)
atapi-cd casts to struct buf to examine B_PHYS
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
The driver constructs a fake disklabel that makes the 'a' partition
cover the entire DVD-RAM disk. This cannot be changed from the user
side. This solution was chosen because most DVD-RAM will have a
UDF (or until we have that CD9660) filesystem on it covering the
entire disk, its not really thought as a real random access device.
This might change over time, but for now this is what we have, and
it is compatible with CDROM's etc, that makes using the minidisk
subsystem less than ideal, because of !modulo BDEV_SIZE blocks.
Call intr_teardown on detach.
Always add non masterdevice from unit 2 upwards.
Update to the pccard code, at least some cards are now working,
more testing to follow.
