and XAUI 10G interfaces in addition RGMII/SGMII 1G interfaces. This driver
is work in progress.
board.c and board.h expanded to include more info.
Only one of rge and nlge can be enabled at a time, rge will be deprecated
when nlge stabilizes.
Submitted by: Sriram Gorti <srgorti at netlogicmicro com>
SMP.
We used to route all PIC based interrupts to cpu 0, and used the per-CPU
interrupt mask to enable/disable interrupts. But the interrupt threads can
run on any cpu on SMP, and the interrupt thread will re-enable the interrupts
on the CPU it runs on when it is done, and not on cpu0 where the PIC will
still send interrupts to.
The fix is move the disable/enable for PIC based interrupts to PIC, we will
ack on PIC only when the interrupt thread is done, and we do not use the
per-CPU interrupt mask.
The changes also introduce a way for subsystems to add a function that
will be called to clear the interrupt on the subsystem. Currently This is
used by the PCI/PCIe for doing additional work during the interrupt
handling.
- Use timer 7 in XLR PIC as a 32 counter
- provide pic_init_timer(), pic_set_timer(), pic_timer_count32() and
pic_timer_count() PIC timer operations.
- register this timer as platform_timecounter on rmi platform.
- style(9) fixes to mips/rmi platform files
- update pic.h to add pic_setup_intr() and use pic_setup_intr() for setting
up interrupts which are routed thru PIC.
- remove rmi_spin_mutex_safe and haslock, and make sure that the functions
are called only after mutexes are available.
- move PIC code to xlr_machdep.c
- move fast message ring code completely to on_chip.c
- move memory initialization to a new function xlr_mem_init()
- style fixes
* Add a function to write to the relevant PLL register
* Break out the PLL configuration for the AR71XX into the CPU ops,
lifted from if_arge.c.
* Add the AR91XX PLL configuration ops, using the AR91XX register
definitions.
This is untested but should at least allow an AR724X to boot.
The current code is lacking the detail needed to expose the PCIe bus.
It is also lacking any NIC, PLL or flush/WB code.
This works well enough to bring a system up to single-user mode
using an MDROOT.
Known Issues:
* The EHCI USB doesn't currently work and will panic the kernel during
attach.
* The onboard ethernet won't work until the PLL routines have been
fleshed out and shoe-horned into if_arge.
* The WMAC device glue (and quite likely the if_ath support)
hasn't yet been implemented.
* Implement a SoC probe function, from Linux, which determines the
SoC family, type and revision. This only probes the AR71xx series
SoC and (currently) panics on others.
* Migrate some of the AR71XX specific hardware init (USB device, determining
system frequencies) into using the cpuops introduced in an earlier commit.
Other SoC specific hardware stuff (per-device flush/WB, GPIO pin wiring,
Ethernet PLL setup, other things I've likely missed) will be introduced in
subsequent commits.
Reviewed by: imp@
Obtained from: (partially) Linux
1. On n64, use XKPHYS to map page table pages instead of KSEG0. Maintain
just one freepages list on n64.
The changes are mainly to introduce MIPS_PHYS_TO_DIRECT(pa),
MIPS_DIRECT_TO_PHYS(), which will use KSEG0 in 32 bit compilation
and XKPHYS in 64 bit compilation.
2. Change macro based PMAP_LMEM_MAP1(), PMAP_LMEM_MAP2(), PMAP_LMEM_UNMAP()
to inline functions.
3. Introduce MIPS_DIRECT_MAPPABLE(pa), which will further reduce the cases
in which we will need to have a special case for 64 bit compilation.
4. Update CP0 hazard definitions for CPU_RMI - the cpu does not need any
nops
Reviewed by: neel
Each of these SoCs have different devices, different hardware initialisation
methods and, quite likely, different quirks. These functions will abstract
out the SoC differences and keep these differences out of the drivers (eg
USB init, if_arge, etc.)
In particular, provide pagesize and pagesizes array, the canary value
for SSP use, number of host CPUs and osreldate.
Tested by: marius (sparc64)
MFC after: 1 month
- Enable KX and UX bits on CPU startup for non-boot CPUs
- Keep the KX bit when in userspace - XTLB handler needs it to access
PCPU data
- revert r210638 partly - we don't need to enable KX on kernel entry
now
Reviewed by: jmallett, imp
1. Move dirty bit emulation code that is duplicted for kernel and user
in trap.c to a function pmap_emulate_modified() in pmap.c.
2. While doing dirty bit emulation, it is not necessary to update the
TLB entry on all CPUs using smp_rendezvous(), we can just update the
TLB entry on the current CPU, and let the other CPUs update their TLB
entry lazily if they get an exception.
Reviewed by: alc, neel
per-cpu variants are also available to be called. The per-cpu variants
are needed for some later optimizations.
Also remove unnecessary casts, do some style fixes.
Reviewed by: alc, neel
r211130 in favor of this more general fix.
This fixes a compilation error for mips 64-bit little endian build.
libexec/rtld-elf/mips/reloc.c:196: warning: right shift count >= width of type
Suggested by: stefanf, jchandra, bde
IPI to a specific CPU by its cpuid. Replace calls to ipi_selected() that
constructed a mask for a single CPU with calls to ipi_cpu() instead. This
will matter more in the future when we transition from cpumask_t to
cpuset_t for CPU masks in which case building a CPU mask is more expensive.
Submitted by: peter, sbruno
Reviewed by: rookie
Obtained from: Yahoo! (x86)
MFC after: 1 month
MIPS doesn't really need to use atomic_cmpset_int() in situations like
this because the software dirty bit emulation in trap.c acquires
the pmap lock. Atomics like this appear to be a carryover from i386
where the hardware-managed TLB might concurrently set the modified bit.
Reviewed by: alc
pmap_page_wired_mappings() counts the number of pv entries for the
specified page that have the pv entry wired flag set to TRUE.
pmap_enter() correctly initializes this flag. However,
pmap_change_wiring() doesn't update the corresponding pv entry flag,
only the PTE. So, the count returned by pmap_page_wired_mappings()
will sometimes be wrong.
In the short term, the best fix would be to eliminate the pv entry
flag and use only the PTE. That flag is wasting non-trivial memory.
Remove pv_wired flag, and use PTE flag to count the wired mappings.
Reviewed by: alc
