routine in one place was setting the valid2 bit to
2 not 1. This meant the PTE was NOT valid and so
you would crash.
In Zero Page there was a incorrect setting of
the valid bit AFTER the actual zero (opps)..
Hopefully this will fix the 0xc0000000 crashes
that I have been seeing (unless of course there are
other problems with these old hacks of mine to get
to memory above 512Meg)
the RMI/XLR has the COP0 and COP2 bits enabled
Plus it needs SX too. Thanks again for JC in
catching this ;-)
Submitted by: JC (jayachandranc@netlogicmicro.com
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
indicating an already initialized lock.
- Check for an empty MSI/MSI-X queue entry before asserting that we have
received a MSI/MSI-X message in order to not panic in case of stray MSI/
MSI-X queue interrupts which may happen in case of using an interrupt
handler rather than a filter.
MFC after: 3 days
page table page instead of creating a temporary mapping to it.
Set the PG_G bit on the page table entries that implement the KPTmap.
Locore initializes the unused portions of the NKPT kernel page table
pages that it allocates to zero. So, pmap_bootstrap() needn't zero
the page table entries referenced by CMAP1 and CMAP3.
Simplify pmap_set_pg().
MFC after: 10 days
to invalidate memory chunk that starts or ends in the middle of
cache line.
This was responsible for one half of the problem preventing umass
to work reliably on some MIPS32 platforms. USBng needs to stop
sharing cache lines between DMA-able memory and other structures
to cure the other half.
Discussed with: imp, gonzo
format is higher than 6-bit instead of relying VGA compatibility flag.
This fixes palette problem of NVIDIA GeForce 6600. Reduce code differences
between palette load/save functions while we are here.
Tested by: danfe
Without this patch it was possible for a different thread that calls
nfs_asyncio() to snitch a newly created nfsiod thread that was
intended for another caller of nfs_asyncio(), because the nfs_iod_mtx
mutex was unlocked while the new nfsiod thread was created. This patch
labels the newly created nfsiod, so that it is not taken by another
caller of nfs_asyncio(). This is believed to fix the problem reported
on the freebsd-stable email list under the subject:
FreeBSD NFS client/Linux NFS server issue.
Tested by: to DOT my DOT trociny AT gmail DOT com
Reviewed by: jhb
MFC after: 2 weeks
Also, account for a quirk of AMD/ATI HPET which reports number of timers
instead of id of the last timer as manadated by the specification.
Currently this has no effect on functionality but in the future we may
make actual use of the HPET timers, not only of its timecounter.
MFC after: 2 weeks
igb now has a queue notion that has a single interrupt
with an RX/TX pair, this will reduce the total interrupts
seen on a system. Both em and igb have a new watchdog
method. igb has fixes from Pyun Yong-Hyeon that have
improved stability, thank you :)
I wish to MFC this for 7.3 asap, please test if able.
Limit early revisions from 6Gb/s to 3Gb/s by default, or they negotiate
only 1.5Gbps, when 3Gb/s devices connected.
Add dummy driver for PATA part of these controllers, preventing generic
driver attach them. It causes system freeze when SATA controller used after
PATA was touched.
locks up in make buildworld.
You need to follow the mips wiki for building
the nfs partition and setup things to mount there
(in the conf and in your bootp setup).
the intention of having two ttys pointing to the same cfe console device was.
Also we were not initializing the output[] array passed in as input to
tty_makedev() so one name of the ttys was garbage.
Fix the code that calls cfe_write() to deal with the case where only a partial
buffer is written out.
cfe_cngetc() needs to return if there is no character available as input.
If we don't do this then the cfe_timeout() function will spin forever
because cfe_cngetc() will only ever return if there is valid input.
Approved by: imp (mentor)
This is a workaround for the fact that the CFE is compiled as a 64-bit
application and therefore sets the SR_KX bit every time we call into
it (for e.g. console).
A TLB miss for any address above 0xc0000000 with the SR_KX bit set will
end up at the XTLB exception vector. We workaround this by copying the
standard TLB handler at the XTLB exception vector.
Approved by: imp (mentor)
through fork_trampoline.
This was caused because we were clearing the SR_INT_IE and setting
SR_EXL bits of the status register at the same time. This meant
that if an interrupt happened while this MTC0 was making its way
through the pipeline the exception processing would see the
status register with SR_EXL bit set. This in turn would mean that
the COP_0_EXC_PC would not be updated so the return from exception
would be to an incorrect address.
It is easy to verify this fix by a program that forks in a loop
and the child just exits:
while (1) {
pid_t pid = vfork();
if (pid == 0)
_exit(0);
if (pid != -1)
waitpid(pid, NULL, 0);
}
Also remove two instances where we set SR_EXL bit gratuitously in exception.S.
Approved by: imp (mentor)
obio. Take advantage of the fact that obio only really supports uart
at the moment to use the uart bus tag always for IOPORT allocations.
# this needs to be redone to conform to FreeBSD standards and allow for
# additional drivers for SoC hardware to attach
