by adding an argument to the VM_SUSPEND ioctl that specifies how the virtual
machine should be suspended, viz. VM_SUSPEND_RESET or VM_SUSPEND_POWEROFF.
The disposition of VM_SUSPEND is also made available to the exit handler
via the 'u.suspended' member of 'struct vm_exit'.
This capability is exposed via the '--force-reset' and '--force-poweroff'
arguments to /usr/sbin/bhyvectl.
Discussed with: grehan@
hides the setjmp/longjmp semantics of VM enter/exit. vmx_enter_guest() is used
to enter guest context and vmx_exit_guest() is used to transition back into
host context.
Fix a longstanding race where a vcpu interrupt notification might be ignored
if it happens after vmx_inject_interrupts() but before host interrupts are
disabled in vmx_resume/vmx_launch. We now called vmx_inject_interrupts() with
host interrupts disabled to prevent this.
Suggested by: grehan@
- Add a generic routine to trigger an LVT interrupt that supports both
fixed and NMI delivery modes.
- Add an ioctl and bhyvectl command to trigger local interrupts inside a
guest. In particular, a global NMI similar to that raised by SERR# or
PERR# can be simulated by asserting LINT1 on all vCPUs.
- Extend the LVT table in the vCPU local APIC to support CMCI.
- Flesh out the local APIC error reporting a bit to cache errors and
report them via ESR when ESR is written to. Add support for asserting
the error LVT when an error occurs. Raise illegal vector errors when
attempting to signal an invalid vector for an interrupt or when sending
an IPI.
- Ignore writes to reserved bits in LVT entries.
- Export table entries the MADT and MP Table advertising the stock x86
config of LINT0 set to ExtInt and LINT1 wired to NMI.
Reviewed by: neel (earlier version)
'invpcid' instruction to the guest. Currently bhyve will try to enable this
capability unconditionally if it is available.
Consolidate code in bhyve to set the capabilities so it is no longer
duplicated in BSP and AP bringup.
Add a sysctl 'vm.pmap.invpcid_works' to display whether the 'invpcid'
instruction is available.
Reviewed by: grehan
MFC after: 3 days
Make the amd64/pmap code aware of nested page table mappings used by bhyve
guests. This allows bhyve to associate each guest with its own vmspace and
deal with nested page faults in the context of that vmspace. This also
enables features like accessed/dirty bit tracking, swapping to disk and
transparent superpage promotions of guest memory.
Guest vmspace:
Each bhyve guest has a unique vmspace to represent the physical memory
allocated to the guest. Each memory segment allocated by the guest is
mapped into the guest's address space via the 'vmspace->vm_map' and is
backed by an object of type OBJT_DEFAULT.
pmap types:
The amd64/pmap now understands two types of pmaps: PT_X86 and PT_EPT.
The PT_X86 pmap type is used by the vmspace associated with the host kernel
as well as user processes executing on the host. The PT_EPT pmap is used by
the vmspace associated with a bhyve guest.
Page Table Entries:
The EPT page table entries as mostly similar in functionality to regular
page table entries although there are some differences in terms of what
bits are used to express that functionality. For e.g. the dirty bit is
represented by bit 9 in the nested PTE as opposed to bit 6 in the regular
x86 PTE. Therefore the bitmask representing the dirty bit is now computed
at runtime based on the type of the pmap. Thus PG_M that was previously a
macro now becomes a local variable that is initialized at runtime using
'pmap_modified_bit(pmap)'.
An additional wrinkle associated with EPT mappings is that older Intel
processors don't have hardware support for tracking accessed/dirty bits in
the PTE. This means that the amd64/pmap code needs to emulate these bits to
provide proper accounting to the VM subsystem. This is achieved by using
the following mapping for EPT entries that need emulation of A/D bits:
Bit Position Interpreted By
PG_V 52 software (accessed bit emulation handler)
PG_RW 53 software (dirty bit emulation handler)
PG_A 0 hardware (aka EPT_PG_RD)
PG_M 1 hardware (aka EPT_PG_WR)
The idea to use the mapping listed above for A/D bit emulation came from
Alan Cox (alc@).
The final difference with respect to x86 PTEs is that some EPT implementations
do not support superpage mappings. This is recorded in the 'pm_flags' field
of the pmap.
TLB invalidation:
The amd64/pmap code has a number of ways to do invalidation of mappings
that may be cached in the TLB: single page, multiple pages in a range or the
entire TLB. All of these funnel into a single EPT invalidation routine called
'pmap_invalidate_ept()'. This routine bumps up the EPT generation number and
sends an IPI to the host cpus that are executing the guest's vcpus. On a
subsequent entry into the guest it will detect that the EPT has changed and
invalidate the mappings from the TLB.
Guest memory access:
Since the guest memory is no longer wired we need to hold the host physical
page that backs the guest physical page before we can access it. The helper
functions 'vm_gpa_hold()/vm_gpa_release()' are available for this purpose.
PCI passthru:
Guest's with PCI passthru devices will wire the entire guest physical address
space. The MMIO BAR associated with the passthru device is backed by a
vm_object of type OBJT_SG. An IOMMU domain is created only for guest's that
have one or more PCI passthru devices attached to them.
Limitations:
There isn't a way to map a guest physical page without execute permissions.
This is because the amd64/pmap code interprets the guest physical mappings as
user mappings since they are numerically below VM_MAXUSER_ADDRESS. Since PG_U
shares the same bit position as EPT_PG_EXECUTE all guest mappings become
automatically executable.
Thanks to Alan Cox and Konstantin Belousov for their rigorous code reviews
as well as their support and encouragement.
Thanks for John Baldwin for reviewing the use of OBJT_SG as the backing
object for pci passthru mmio regions.
Special thanks to Peter Holm for testing the patch on short notice.
Approved by: re
Discussed with: grehan
Reviewed by: alc, kib
Tested by: pho
command line option "-m <memsize in MB>" to specify the memory size.
Prior to this change the user needed to explicitly specify the amount of
memory allocated below 4G (-m <lowmem>) and the amount above 4G (-M <highmem>).
The "-M" option is no longer supported by 'bhyveload' and 'bhyve'.
The start of the PCI hole is fixed at 3GB and cannot be directly changed
using command line options. However it is still possible to change this in
special circumstances via the 'vm_set_lowmem_limit()' API provided by
libvmmapi.
Submitted by: Dinakar Medavaram (initial version)
Reviewed by: grehan
Obtained from: NetApp
Prior to this change pinning was implemented via an ioctl (VM_SET_PINNING)
that called 'sched_bind()' on behalf of the user thread.
The ULE implementation of 'sched_bind()' bumps up 'td_pinned' which in turn
runs afoul of the assertion '(td_pinned == 0)' in userret().
Using the cpuset affinity to implement pinning of the vcpu threads works with
both 4BSD and ULE schedulers and has the happy side-effect of getting rid
of a bunch of code in vmm.ko.
Discussed with: grehan
