Remote host can advertise smaller MSS than that of sender so upper
stack might have adjusted the MSS which in turn generates IP
packets that are less size than that of interface MTU.
Reported by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
Tested by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
MFC after: 3 days
TCPSTAT_INC(), rather than directly manipulating the fields across the
kernel. This will make it easier to change the implementation of
these statistics, such as using per-CPU versions of the data structures.
MFC after: 3 days
1) Flag it and only access that command on the 3c1
2) The TX PLL appears to power down when not in use, so we have to power
it back up when we've been idle. Do this at the start of ifstart.
Otherwise we fall off the net.
have other media to test against, I've left that media reporting
unchanged.
o Enable the TX_PLL when we enable TX. This is harmless on most
cards, but required to get the 3c1 CF card working. Power savings
could be had by managing this better, but for now it gets my card
working.
We typically wire translation to devices with TLB1 entries and
pmap_kextract() does not know about those and returns 0. This
causes false positives (read: all serial ports suddenly become
the console).
Do not use Giant for kbdmux(4) locking. This is wrong and apparently
causing more problems than it solves. This will re-open the issue
where interrupt handlers may race with kbdmux(4) in polling mode.
Typical symptoms include (but not limited to) duplicated and/or
missing characters when low level console functions (such as gets)
are used while interrupts are enabled (for example geli password
prompt, mountroot prompt etc.)
MFC after: 3 days
(framing, parity, etc), but does not indicate characters
being received. Since no chracters have been received,
ignore the line errors.
PR: 131006
MFC after: 3 days
instead of just register one for the first adapter. Without doing this
there would be some data loss upon shutdown because data could be ignored
when flushing to disk.
MFC after: 3 days
- override_kernel_driver() has been removed since this is an
in-tree version of driver.
- __DATE__ and __TIME__ removed from version string to make
binary update builders happy.
- Utilize pause(9) for __FreeBSDversion >= 700033 (redo 167086).
- Utilize kproc_suspend_check() for __FreeBSDversion >= 800002.
(redo 172836).
- Don't read past end of pVDevice (redo 143787).
- Make sure that controller and channel are initialized (redo 169823).
- Don't include cam/cam_xpt_periph.h (redo 158177).
MFC After: 3 days
and update comments about original patches doing this and it not
working. It works for both the DL10019 and DL10022 based cards that I
have. It really helps the DL10019 cards, since they were using 8k
instead of the normal 16k that regular NE-2000 cards help.
# Note to self: need to provide a common routine to setup memory
# parameters.
DP8390-based cards have no generic way of reporting status of the link
or setting the media type. Some specific versions of these cards do,
however, allow for this, and we already support some of them. Make
the 'ed' experience more uniform by providing "autoselect" as the
meida and status "active" always. This won't affect the chips that
provide more specific details.
It makes little sense to use 100 Hz polling in dcons. We cannot live
without polling, because that's just how dcons works. It polls the
buffer filled by the firewire hardware. 25 Hz is probably enough for
most use cases.
Discussed with: rwatson
Tested by: kan
dcons_drv_init invocations. Testing return value for 0 does not work for
cases where dcons_drv_init was called already as part of low level
console initialization.
