- Clear PCIM_CMD_MWRICEN:
some chips seem to have problem with write invalidate.
clearing this bit fixes SBP timeout problem.
Tested by: Michael Reifenberger <Michael.Reifenberger@Plaut.de>
- Set PCIM_CMD_SERRESPEN and PCIM_CMD_PERRESPEN
- Moderate value for latency timer.
Change 27224 by imp@imp_hammer on 2003/03/22 00:16:22
Put what I think are the correct TX RATE translation tables
in place for LUCENT firmware. This is based on the 4.x driver.
Maybe it should be table driven?
ifconfig wi0 media DS/11Mbps still fails, but it fails before
we even get to the txrate stuff, so other things are wrong.
Change 27225 by imp@imp_hammer on 2003/03/22 00:45:11
Default ic_fixed_rate to -1. This is the same thing as autoselect.
There really should be a #define for this...
- Use it in atacontrol(8) when listing ATA devices instead of
stopping at the first ENXIO received.
This makes atacontrol list work on my sparc64 where the two ATA
channels I have are numbered 2 and 3.
Reviewed by: sos
one tx buffer for these cards. The old driver only used one. We use
1 for symbol, and 3 for prism cards.
o Don't do the maximum loops thing in the ISR. In fact, revert to the
old interrupt handler. Lucent cards don't seem to work too well if
you don't disable/enable interrupts from the card in the ISR.
Between these two changes, Lucent cards suck less. They work in
autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a
specific media speed doesn't work, and I've had a few issues even with
these patches. They turn a former brick into a nearly useful card.
These patches work on the prism 2 and 2.5 PC Card cards that I have.
I've not tested this on PCI cards. I suspect, but couldn't find
proof, that they were the reason that the ISR was changed so radically
from its FreeBSD roots in NetBSD. We might need to have a variant ISR
if so.
code both seem to call wi_start (directly or via the if_start pointer)
without checking to see if OACTIVE is 0. In addition, I think that
with the use of 3 transmit buffers this routine can be called with
OACTIVE set, but I might be mistaken about that (and it doesn't
matter).
Reviewed by: sam
Noticed by: imp, alfred, ambrisko
now unnecessary hack from the previous commit;
- Add support for Interrupt Latch Register (ILR) into puc(4). So far only
ILRs compatible with specifications from Digi International are supported.
Support for other types of ILRs could be easily added later;
- Correct clock frequency for IC Book Labs Dreadnought x16 Lite board;
- Enable ILR detection/usage for IC Book Labs Dreadnought x16 boards.
Sponsored by: IC Book Labs
MFC after: 2 weeks
this card is based on 16750 UART, modify sio(4) a bit to ignore 16750-specific
7th bit of MCR when probing card. This allows card to be detected and attached
as 16550A-compatible device. More work needs to be done in order to enable
nice 16750-specific features such as larger fifo buffer and higher speeds.
Sponsored by: IC Book Labs
MFC after: 2 weeks
Harti Brandt's effort.
remove the DMA test to detect problems of the first generation PCI chipsets
back in 1998.
it is no longer needed and has been the source of the false alarm that
the driver uses too much stack space.
monitors the entropy data harvested by crypto drivers to verify it complies
with FIPS 140-2. If data fails any test then the driver discards it and
commences continuous testing of harvested data until it is deemed ok.
Results are collected in a statistics block and, optionally, reported on
the console. In normal use the overhead associated with this driver is
not noticeable.
Note that drivers must (currently) be compiled specially to enable use.
Obtained from: original code by Jason L. Wright
conditional in each driver on foo_RNDTEST being defined_
o bring HIFN_DEBUG and UBSEC_DEBUG out to be visible options; they control
the debugging printfs that are set with hw.foo.debug (e.g. hw.hifn.debug)
