- Add entries in the uscanner.4 man page (along with missing 3500).
PR: usb/100957 [1], usb/100992 [2]
Submitted by: Jim Teresco <terescoj@teresco.org> [1],
Walter C. Pelissero <walter.pelissero@iesy.net> [2]
MFC after: 3 days
will fix a problem where you boot w/ the default of autoselect, but then
set the speed to 100/full, the switch will keep the autoselect/100/full
negotiation... This will continue to work till someone resets the switch
or unplugs the cable resulting in the switch failing to autoneg and falling
back to 100/half, causing a hard to track down duplex mismatch..
Submitted by: nCircle Network Security, Inc.
MFC after: 1 week
- Add support for the Conexant Waikiki/CX20551-22, found
in most Toshiba P100 series laptops. Despite of growing
urban legend of "unsupported Conexant", this codec is fully
supported in this driver.
Note: Toshiba P100 has broken (acpi) BIOS, thus rendering
its soundchip useless. Please disable ACPI, or get
BIOS updates (if any).
Found/tested by: Vulpes Velox <v.velox@vvelox.net>
URL: http://lists.freebsd.org/pipermail/freebsd-multimedia/2006-September/004896.html
- Parser cleanups to handle possible oss/mixer collision. Found
after parsing Conexant Waikiki nodes.
- Increase resilient against resource failure during attach/detach.
- Implement simple config through hint.pcm.<unit>.config. Supported
options:
gpio0 (default on Acer), gpio1, gpio2, softpcmvol,
fixedrate (default), forcestereo (default)
* Option prefixed with "no" (such as "nofixedrate") will do
the opposite.
* Options can be separated using space " " or comma ",".
* The "no" option will take precedence over anything else.
Example:
hint.pcm.0.config="gpio2,nofixedrate,noforcestereo,nogpio0,softpcmvol"
hint.pcm.0.config="softpcmvol noforcestereo"
or not the OS has to wait for RX_RDY or TX_RDY to be set before the OS sets
the control code in the control/status register. Looking at the interface
design, it seems that RX_RDY and TX_RDY are probably there to protect
access to the data register and have nothing to do with the control/status
register. Nevertheless, try to take what I think is the more conservative
approach and always wait for the appropriate [TR]X_RDY flag to be set
before writing any of the WR_NEXT, WR_END, RD_START, or RD_NEXT control
codes to the control/status register.
close and re-open the default pipe instead of relying on the host
controller driver to notice the changes. Remove the unreliable code
that attempted to update these fields while the pipe was active.
This fixes a case where the hardware could cache and continue to
use the old address, resulting in a "getting first desc failed"
error.
PR: usb/103167
- Fix support for ASUS M5200ae (buggy BIOS)
- Fix few problems, reported by Coverity Prevent (TM).
CID: 246991, 246676, 246675, 246674, 246477
Found by: Coverity Prevent (TM)
The parallel LINT build sometimes broke if kernel-depend wasn't
fast enough in generating ukbdmap.h. If someone thinks this
option would still be useful for the module, a proper fix is
to add the code generating ukbdmap.h into modules/ukbd/Makefile
and backing this change out.
Add support for Intel High Definition Audio Controller.
This driver make a special guarantee that "playback" works
on majority hardwares with minimal or without specific vendor
quirk.
This driver is a product of collaborative effort made by:
Stephane E. Potvin <sepotvin@videotron.ca>
Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Wesley Morgan <morganw@chemikals.org>
Daniel Eischen <deischen@FreeBSD.org>
Maxime Guillaud <bsd-ports@mguillaud.net>
Ariff Abdullah <ariff@FreeBSD.org>
....and various people from freebsd-multimedia@FreeBSD.org
Refer to snd_hda(4) for features and issues.
Welcome To HDA.
Sponsored by: Defenxis Sdn. Bhd.
This driver make a special guarantee that "playback" works
on majority hardwares with minimal or without specific vendor
quirk.
This driver is a product of collaborative effort made by:
Stephane E. Potvin <sepotvin@videotron.ca>
Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Wesley Morgan <morganw@chemikals.org>
Daniel Eischen <deischen@FreeBSD.org>
Maxime Guillaud <bsd-ports@mguillaud.net>
Ariff Abdullah <ariff@FreeBSD.org>
....and various people from freebsd-multimedia@FreeBSD.org
Refer to snd_hda(4) for features and issues.
Welcome To HDA.
Sponsored by: Defenxis Sdn. Bhd.
- fix multiple initialization of the first codec (support for more than
one codec should be added in the future)
- use spicds instead of ak452x module
Submitted by: "Konstantin Dimitrov" <kosio.dimitrov@gmail.com>
stripping was disabled due to being in promisc mode. This is a hardware
bug. Update comment to explicitly state the reason the manual vlan tag
insertion in this case. See rev. 1.53 for further information as well.
Noticed by: jhb
generic vlan_start() takes care of it when vlan hardware insertion is disabled.
In em_set_promisc() add a note that BPF may also be enabled without going into
promisc mode.
Reviewed by: jfv
IP options and add skeleton IPv6 support. The new code structure can also be
easily enhanced to support new/more protocols (SCTP) in the future.
Reviewed by: jfv
and add skeleton IPv6 support. The new code structure can also be easily
enhanced to support new/more protocols (SCTP) and IP fragmentation in the
future.
In em_encap() only try to do TSO if 'dotso' is true.
Reviewed by: jfv
- EFBIG means the mbuf chain was too long and bus_dma ran out of segments.
Defragment the mbuf chain and try again. (Already existed, not changed.)
- ENOMEM means bus_dma could not obtain enough bounce buffers at this point
in time. Defer sending and try again later.
- All other errors, in particular EINVAL, are fatal and prevent the mbuf
chain from ever going through. Drop it and report error.
- Checking (nsegs == 0) is unnecessary as bus_dmamap_load_mbuf_sg() always
reports an error if it is < 1.
This prevents broken packets from clogging the interface queue indefinately.
Discussed with: scottl
Reviewed by: jfv
commit.
1) sys/dev/sound/pcm/sound.h
sys/dev/sound/pcm/channel.c
* Be more specific: SD_F_SOFTVOL -> SD_F_SOFTPCMVOL
2) sys/dev/sound/pcm/mixer.[ch]
* Implement
mix_setparentchild()
mix_setrealdev()
mix_getparent()
mix_getchild()
The purpose of these functions is implement relative volume
adjustment, such as to tie two or more mixer device into a
single logical device. Usefull for the upcoming HDA driver
and few AC97 codec (such as AD1981B) where the master volume
"vol" need to be implemented using this logical manner.
3) sys/dev/sound/pcm/ac97_patch.[ch]
* Patch for AD1981B codec to enable (automuting) headphone jack sense.
4) sys/dev/sound/pcm/ac97.c
* Implement proper logical master volume for AD9181B codec
through various mix_set{parentchild,realdev}(). Tie both
"ogain" (headphone volume) and "phone" (speaker/lineout) to
a logical "vol".
5) sys/dev/sound/pcm/usb/uaudio_pcm.c
* ditto, for "vol" -> { "pcm" }.
MFC after: 1 month
ioctls passing integer arguments should use the _IOWINT() macro.
This fixes a lot of ioctl's not working on sparc64, most notable
being keyboard/syscons ioctls.
Full ABI compatibility is provided, with the bonus of fixing the
handling of old ioctls on sparc64.
Reviewed by: bde (with contributions)
Tested by: emax, marius
MFC after: 1 week
The key problem was that the aperture size detection using the MSAC bit
doesn't work -- the bit appears to be set even when it shouldn't be. Linux
takes a different approach, testing for a bit of the GMADR (PCIR_BAR(2)) being
set. However, as I don't think that's a safe way to test aperture size, we
just allocate the resource and check its size. This also pointed out that
agp_generic_attach hadn't been allocating our aperture resource, which may
have caused problems in some cases.
Also corrected is a minor copy-and-pasteo in an error case.
PR: kern/103079
Submitted by: mnag
Tested on: i945GM, i915GM
MFC after: 2 weeks
The goal was to sync with the OSSv4 API 4Front Technologies uses in their
proprietary OSS driver. This was successful as far as possible. The part
of the API which is stable is implemented, for the rest there are some
stubs already.
New system ioctls:
- SNDCTL_SYSINFO - obtain audio system info (version, # of audio/midi/
mixer devices, etc.)
- SNDCTL_AUDIOINFO - fetch details about a specific audio device
- SNDCTL_MIXERINFO - fetch details about a specific mixer device
New audio ioctls:
- Sync groups (SNDCTL_DSP_SYNCGROUP/SNDCTL_DSP_SYNCSTART) which allow
triggered playback/recording on multiple devices (even across processes
simultaneously).
- Peak meters (SNDCTL_DSP_GETIPEAKS/SNDCTL_DSP_GETOPEAKS) - can query
audio drivers for peak levels (needs driver support, disabled for now).
- Per channel playback/recording levels -
SNDCTL_DSP_{GET,SET}{PLAY,REC}VOL. Note that these are still in name
only, just wrapping around the AC97-style mixer at the moment. The next
step is to push them down to the drivers.
Audio ioctls still under development by 4Front (for which stubs may exist
in this commit):
- SNDCTL_GETNAME, SNDCTL_{GET,SET}{SONG,LABEL}
- SNDCTL_DSP_{GET,SET}_CHNORDER
- SNDCTL_MIX_ENUMINFO, SNDCTL_MIX_EXTINFO - (might be documented enough in
the OSS releases to work on this. These ioctls cover the cool "twiddle
any knob on your card" features.)
Missing:
- SNDCTL_DSP_COOKEDMODE -- this ioctl is used to give applications direct
access to a card's buffers, bypassing the feeder architecture. It's
a toughy -- "someone" needs to decide :
(a) if this is desireable, and (b) if it's reasonably feasible.
Updates for driver writers:
So far, only two routines to the channel class (in channel_if.m) are added.
One is for fetching a list of discrete supported playback/recording rates
of a channel, and the other is for fetching peak level info (useful for
drawing peak meters). Interested parties may want to help pushing down
SNDCTL_DSP_{GET,SET}{PLAY,REC}VOL into the drivers.
To use the new stuff you need to rebuild the sound drivers or your kernel
(depending on if you use modules or not) and to install soundcard.h (a
buildworld/installworld handles this).
Sponsored by: Google SoC 2006
Submitted by: ryanb
Many thanks to: 4Front Technologies for their cooperation, explanations
and the nice license of their soundcard.h.
- Split out the communication protocols into their own files and use
a couple of function pointers in the softc that the commuication
protocols setup in their own attach routine.
- Add support for the SSIF interface (talking to IPMI over SMBus).
- Add an ACPI attachment.
- Add a PCI attachment that attaches to devices with the IPMI interface
subclass.
- Split the ISA attachment out into its own file: ipmi_isa.c.
- Change the code to probe the SMBIOS table for an IPMI entry to just use
pmap_mapbios() to map the table in rather than trying to setup a fake
resource on an isa device and then activating the resource to map in the
table.
- Make bus attachments leaner by adding attach functions for each
communication interface (ipmi_kcs_attach(), ipmi_smic_attach(), etc.)
that setup per-interface data.
- Formalize the model used by the driver to handle requests by adding an
explicit struct ipmi_request object that holds the state of a given
request and reply for the entire lifetime of the request. By bundling
the request into an object, it is easier to add retry logic to the various
communication backends (as well as eventually support BT mode which uses
a slightly different message format than KCS, SMIC, and SSIF).
- Add a per-softc lock and remove D_NEEDGIANT as the driver is now MPSAFE.
- Add 32-bit compatibility ioctl shims so you can use a 32-bit ipmitool
on FreeBSD/amd64.
- Add ipmi(4) to i386 and amd64 NOTES.
Submitted by: ambrisko (large portions of 2 and 3)
Sponsored by: IronPort Systems, Yahoo!
MFC after: 6 days
Unfortunately, the QUEUE FULL event only tells you Bus && Target.
It doesn't tell you lun. In order for the XPT_REL_SIMQ action to
work, we have to have a real lun. But which one? For now, just
iterate over MPT_MAX_LUNS.
Practically speaking, this is only going to be happening for lower
quality SAS or SATA drives behind the SAS controller, which means
only lun 0, so it's not so bad.
Helpful Reminder Nagging from: John Baldwin, Fred Whiteside
MFC after: 5 days
of the chip to let ASF/IPMI firmware to respond to IPMI after attaching
and when the chip is down. David looked at it but could really say
what they right minimal config. stuff would be. It's not documented.
I figured this out via trial and error.
Reviewed by: davidch
is incorrect, and causes endianness bugs on 64-bit big-endian
machines (sparc64), it's the best choice for now, as many of
these IOCTLs are used inside the kernel, and bogusly pass an
argument as "int *" which results in unaligned access panics
on sparc64 when attempting to dereference them via *(intptr_t *).
(Several of us are working on a real fix, which is uneasy.)
part of the hal distribution early on when the hal was built for
each os but it's been portable for a long time so move the os-specific
code out (and off the vendor branch)
o correct the copyright on ah_osdep.?; it was mistakenly given a
restricted license and not a dual-bsd/gpl license
o remove the module api definition as it was never used
o fixup include paths for move of ah_osdep.h
MFC after: 2 weeks
with other commonly used sysctl name spaces, rather than declaring them
all over the place.
MFC after: 1 month
Sponsored by: nCircle Network Security, Inc.
m_pkthdr.ether_vlan. The presence of the M_VLANTAG flag on the mbuf
signifies the presence and validity of its content.
Drivers that support hardware VLAN tag stripping fill in the received
VLAN tag (containing both vlan and priority information) into the
ether_vtag mbuf packet header field:
m->m_pkthdr.ether_vtag = vlan_id; /* ntohs()? */
m->m_flags |= M_VLANTAG;
to mark the packet m with the specified VLAN tag.
On output the driver should check the mbuf for the M_VLANTAG flag to
see if a VLAN tag is present and valid:
if (m->m_flags & M_VLANTAG) {
... = m->m_pkthdr.ether_vtag; /* htons()? */
... pass tag to hardware ...
}
VLAN tags are stored in host byte order. Byte swapping may be necessary.
(Note: This driver conversion was mechanic and did not add or remove any
byte swapping in the drivers.)
Remove zone_mtag_vlan UMA zone and MTAG_VLAN definition. No more tag
memory allocation have to be done.
Reviewed by: thompsa, yar
Sponsored by: TCP/IP Optimization Fundraise 2005
- Added support for multicast filtering, now that the firmware
supports it. Note that this is not yet tested, as multicast
seems to panic -current (even w/o mxge loaded)
- Added workaround to cope with different irq data struct size on
pre-multicast firmware which can found running on nics.
- Added Intel E5000 PCIe chipsets to list providing aligned completions.
- Replaced various magic constants with #defines, now that they are
defined in the firmware headers.
in the transmit busdma tag, so I moved the segment list off the
stack.
- Fixed transmit routine to ensure it doesn't read past the end
of an mbuf when parsing headers.
- Corrected handling of odd length segments. Setting MXGEFW_FLAGS_ALIGN_ODD
is required only when offloading the checksum of that frame.
Sponsored by: Myricom Inc.
if_watchdog, etc., or in functions used only in these methods.
In all other functions in the driver use device_printf().
- Use __func__ instead of typing function name.
Submitted by: Alex Lyashkov <umka sevcity.net>
if_ioctl, if_watchdog, etc, or in functions that are used by
these methods only. In all other cases use device_printf().
This also fixes several panics, when if_printf() is called before
softc->ifp was initialized.
Submitted by: Alex Lyashkov <umka sevcity.net>
in syscons. This replaces a simple access semaphore that was assumed to be
protected by Giant but often was not. If two threads that were otherwise
SMP-safe called printf at the same time, there was a high likelyhood that
the semaphore would get corrupted and result in a permanently frozen video
console. This is similar to what is already done in the serial console
drivers.
Instead, we want busses to explicitly specify an add_child routine if they
want to support identify routines, but by default disallow having outside
drivers add devices.
- Give smbus(4) an explicit bus_add_child() method.
Requested by: imp
- Change smbus_callback() to pass a void * rather than caddr_t.
- Change smbus_bread() to pass a pointer to the count and have it be an
in/out parameter. The input is the size of the buffer (same as before),
but on return it will contain the actual amount of data read back from
the bus. Note that this value may be larger than the input value. It
is up to the caller to treat this as an error if desired.
- Change the SMB_BREAD ioctl to write out the updated struct smbcmd which
will contain the actual number of bytes read in the 'count' field. To
preserve the previous ABI, the old ioctl value is mapped to SMB_OLD_BREAD
which doesn't copy the updated smbcmd back out to userland. I doubt anyone
actually used the old BREAD anyway as it was rediculous to do a bulk-read
but not tell the using program how much data was actually read.
- Make the smbus driver and devclass public in the smbus module and
push all the DRIVER_MODULE()'s for attaching the smbus driver to
various foosmb drivers out into the foosmb modules. This makes all
the foosmb logic centralized and allows new foosmb modules to be
self-contained w/o having to hack smbus.c everytime a new smbus driver
is added.
- Add a new SMB_EINVAL error bit and use it in place of EINVAL to return
an error for bad arguments (such as invalid counts for bread and bwrite).
- Map SMB bus error bits to EIO in smbus_error().
- Make the smbus driver call bus_generic_probe() and require child drivers
such as smb(4) to create device_t's via identify routines. Previously,
smbus just created one anonymous device during attach, and if you had
multiple drivers that could attach it was just random chance as to which
driver got to probe for the sole device_t first.
- Add a mutex to the smbus(4) softc and use it in place of dummy splhigh()
to protect the 'owner' field and perform necessary synchronization for
smbus_request_bus() and smbus_release_bus().
- Change the bread() and bwrite() methods of alpm(4), amdpm(4), and
viapm(4) to only perform a single transaction and not try to use a
loop of multiple transactions for a large request. The framing and
commands to use for a large transaction depend on the upper-layer
protocol (such as SSIF for IPMI over SMBus) from what I can tell, and the
smb(4) driver never allowed bulk read/writes of more than 32-bytes
anyway. The other smb drivers only performed single transactions.
- Fix buffer overflows in the bread() methods of ichsmb(4), alpm(4),
amdpm(4), amdsmb(4), intpm(4), and nfsmb(4).
- Use SMB_xxx errors in viapm(4).
- Destroy ichsmb(4)'s mutex after bus_generic_detach() to avoid problems
from child devices making smb upcalls that would use the mutex during
their detach methods.
MFC after: 1 week
Reviewed by: jmg (mostly)
