Kill the slightly bogus #define for DECODE_PROTOTYPE
Be less verbose. Hide most (all I hope) of the CIS
parsing behind cardbus_debug_cis (which is set with
hw.cardbus.debug_cis=1).
This doesn't fix problems with parsing, but should make cardbus
less chatty. There appears to be some issues still with the
parsing of the CIS, but this won't fix them.
Prompted by: scottl
Second part of the kldload patches for cardbus. This makes
kldload of a driver for a device that's inserted now appears
to work. To make it work, we only do a power cycle of the card
if there's no children drivers attached.
This likely is papering over bogosities in the power system. The
power sequence needs to be re-written, so I'll not worry about
the papering over until the re-write.
disk I/O processing.
The intent is that the disk driver in its hardware interrupt
routine will simply schedule the bio on the task queue with
a routine to finish off whatever needs done.
The g_up thread will then schedule this routine, the likely
outcome of which is a biodone() which queues the bio on
g_up's regular queue where it will be picked up and processed.
Compared to the using the regular taskqueue, this saves one
contextswitch.
Change our scheduling of the g_up and g_down queues to be water-tight,
at the cost of breaking the userland regression test-shims.
Input and ideas from: scottl
Cut up requests into smaller bits if they are longer than the drivers
disk->d_maxsize or dev->si_iosize_max.
Properly handle the race condition when using g_clone_bio() is used
without having the single-threadedness of g_down/g_up secure locking.
and d_stripesisze;
Introduce si_stripesize and si_stripeoffset in struct cdev so we
can make the visible to clustering code.
Add stripesize and stripeoffset to providers.
DTRT with stripesize and stripeoffset in various places in GEOM.
The locking here needs to be revisited, but this ought to get rid of the
LOR messages that people are complaining about for now. I imagine either
I or someone else interested with smp will eventually clear this up.
unconditionally. kldloading a cardbus driver was shooting down other
attached devices because most drivers assume that one cannot
power-cycle cards w/o the driver knowning about it.
Submitted by: simokawa-san
- Use the ratio of kg_runtime / kg_slptime to determine our dynamic priority.
- Scale kg_runtime and kg_slptime back when the sum of the two exceeds
SCHED_SLP_RUN_MAX. This allows us to slowly forget old behavior.
- Scale back the runtime and slptime in fork so that the new process has the
same ratio but much less accumulated time. This causes new behavior to be
noticed more quickly.
blocks now, which should eliminate problems with the driver failing to
attach due to insufficient contiguous RAM. Allow the FIB pool to grow
from the default of 128 to the max of 512 as demand grows. Also pad the
adapter init struct to work around the 2120/2200 DMA bug now that there
is no longer a FIB slab.
idle time.
Statistics now default to "on" and can be turned off with
sysctl kern.geom.collectstats=0
Performance impact of statistics collection is on the order of
800 nsec per consumer/provider set on a 700MHz Athlon.
that is protected by the vnode lock.
- Move B_SCANNED into b_vflags and call it BV_SCANNED.
- Create a vop_stdfsync() modeled after spec's sync.
- Replace spec_fsync, msdos_fsync, and hpfs_fsync with the stdfsync and some
fs specific processing. This gives all of these filesystems proper
behavior wrt MNT_WAIT/NOWAIT and the use of the B_SCANNED flag.
- Annotate the locking in buf.h
buf lists, synchronization variables, and atomic ops for the counters.
This change does not remove giant from any code although some pushdown
may be possible.
- In vfs_bio_awrite() don't access buf fields without the buf lock.
* implement watchdog timer.
* check all standing transactions in firewire_xfer_timeout().
- Add firewire_xferq_drain() for fw_busreset().
- Add/improve some debug messages.
- Call fw_xfer_done() if retry handler is NULL.
o Add a MD header private to libc called _fpmath.h; this header
contains bitfield layouts of MD floating-point types.
o Add a MI header private to libc called fpmath.h; this header
contains bitfield layouts of MI floating-point types.
o Add private libc variables to lib/libc/$arch/gen/infinity.c for
storing NaN values.
o Add __double_t and __float_t to <machine/_types.h>, and provide
double_t and float_t typedefs in <math.h>.
o Add some C99 manifest constants (FP_ILOGB0, FP_ILOGBNAN, HUGE_VALF,
HUGE_VALL, INFINITY, NAN, and return values for fpclassify()) to
<math.h> and others (FLT_EVAL_METHOD, DECIMAL_DIG) to <float.h> via
<machine/float.h>.
o Add C99 macro fpclassify() which calls __fpclassify{d,f,l}() based
on the size of its argument. __fpclassifyl() is never called on
alpha because (sizeof(long double) == sizeof(double)), which is good
since __fpclassifyl() can't deal with such a small `long double'.
This was developed by David Schultz and myself with input from bde and
fenner.
PR: 23103
Submitted by: David Schultz <dschultz@uclink.Berkeley.EDU>
(significant portions)
Reviewed by: bde, fenner (earlier versions)
Insted of embedding a struct g_stat in consumers and providers, merely
include a pointer.
Remove a couple of <sys/time.h> includes now unneeded.
Add a special allocator for struct g_stat. This allocator will allocate
entire pages and hand out g_stat functions from there. The "id" field
indicates free/used status.
Add "/dev/geom.stats" device driver whic exports the pages from the
allocator to userland with mmap(2) in read-only mode.
This mmap(2) interface should be considered a non-public interface and
the functions in libgeom (not yet committed) should be used to access
the statistics data.
so be more careful about calling stackgap_init.
Tested by: Fred Souza <fred@storming.org>
2) Linux_sendmsg was forgetting to fill out the bsd_args struct.
Reviewed by: ume
3) The args to linux_connect have differently named types on alpha and
i386, so add a cast to stop gcc complaining.
Spotted by: peter
- Cache temp. keys so they are preserved across suspend/resume (MPI-350)
- Reads and writes are real fast to the MPI-350 causing early timeouts so
wait do some DELAYs to slow things down in the spin loops.
- Stream line setting RIDs when they are better to be set via another
function
- Add better support for setting home key via "ifconfig an0 wepkey 9:<key>"
Tested by: Peter Radcliffe <pir@pir.net> (in -stable)
myself in -current & -stable
MFC in: 3 days
Add debug.sizeof.g_stat sysctl.
Set the id field of the g_stat when we create consumers and providers.
Remove biocount from consumer, we will use the counters in the g_stat
structure instead. Replace one field which will need to be atomically
manipulated with two fields which will not (stat.nop and stat.nend).
Change add companion field to bio_children: bio_inbed for the exact
same reason.
Don't output the biocount in the confdot output.
Fix KASSERT in g_io_request().
Add sysctl kern.geom.collectstats defaulting to off.
Collect the following raw statistics conditioned on this sysctl:
for each consumer and provider {
total number of operations started.
total number of operations completed.
time last operation completed.
sum of idle-time.
for each of BIO_READ, BIO_WRITE and BIO_DELETE {
number of operations completed.
number of bytes completed.
number of ENOMEM errors.
number of other errors.
sum of transaction time.
}
}
API for getting hold of these statistics data not included yet.
handy if the machine is on another floor. A minor issue with this is that
these functions are also used by the debugger, so its possible to break into
the debugger from the debugger.
PR: sparc64/47143
Reviewed by: benno
Approved by: jake (mentor)
correctly tell CAM to requeue the command and then freeze it's queue. The
problem was that when resources became available again, it wouldn't tell
CAM to unfreeze it's queue, so no more commands would ever be delivered.
This is simialr to the bug that was fixed in the cciss driver last year.
This is a bug in 4-STABLE also, but is probably masked by the OS being
fast enough to drain the completion queue before it fills up.
Also add some diagnostics avaialble when compiled with MLY_DEBUG.
Thanks very much to LSI Corp for donating equipment to track this down,
and Vaidus Damosevicius for pestering me long enough to get it fixed.
We may actually be increasing Giant contention doing so because the
actual stuff we do is very cheap.
Also I am not convinced there is not a tiny window for a race here.
Sync with userland test framework which now deals better with pcm feeder kobj
emulation.
Reduce max rate from 96kHz to 48kHz as userland tests found a few bad
points about 90kHz and we don't care about operating up there for now.
DDB when the interrupt button (aka the "programmer's switch") is pressed.
This isn't unfortunately an NMI, but it's a handy way to get into DDB
quickly if needed.
- Move the command timeout check from a separate repeating timeout to the
kthread since the kthread is already running periodically.
- Move printing the hardware print buffer to the kthread.
- Properly shut down the kernel thread on detach.
- Detach the child array devices on detach.
- Don't issue a controller halt command on detach. Doing so requires a PCI
reset to wake the controller back up. The driver can now be unloaded as
long as CAM support is not enabled.
similar patch has been in 4.x for a while, but is more hacky there.)
For this to work, vinum has to be loaded early (e. g. from
boot/loader), for obvious reasons. If the kernel env variable
(aka. loader variable) "vinum.autostart" is set, vinum then asks the
sysctl kern.disks for all available disks in the system, and scans
them for possible vinum headers.
For statically compiled kernels, this behaviour can be obtained even
without boot/loader by using "options VINUM_AUTOSTART" (though this is
not the recommended way).
Alternatively, the 4.x way to specify "vinum.drives" is also supported.
No further hacks (like the 4.x "vinum.root" variable) are needed,
since in 5.x, mountroot() asks back at the drivers to have them
resolve the name of the root FS into a dev_t (using the dev_clone
eventhandler).
(The MFC reminder below is for a partial MFC for vinum.autostart, the
rest is already there in 4.x.)
Timed out on: grog
MFC after: 2 weeks
we have the rc4 code already in the kernel (via wlan stuff or awi).
Add a dependency on the rc4 module so if it doesn't exist then load it.
Reviewed by: archie
1) It is already called in init_main.c:proc0_post()
2) It is called each time read_random_phony() called, because "initialized"
variable is never set to 1.
Approved by: markm
- Add hid.h
Obtained from: NetBSD
NOTE: This undoes some changes I'd made to prefix the processor name defines
with PVR_. This was due to my original decision to use MPC750 as a cpu name.
With this changed, the PVR_ change is no longer required.
Remove all the stuff that does not relate to the TSC.
Change the calibration to use DELAY(1000000) rather than trying to check
it against the CMOS RTC, this drastically increases precision:
Using 25 samples on a Athlon 700MHz UP machine I find:
stddev min max average
CMOS 22200 Hz -74980 Hz 34301 Hz 704928721 Hz
DELAY 1805 Hz -1984 Hz 2678 Hz 704937583 Hz
(The difference between the two averages is not statistically significant.)
expressed in PPM of the frequency:
stddev min max
CMOS 31.49 PPM -106.37 PPM 48.66 PPM
DELAY 2.56 PPM 2.81 PPM 3.80 PPM
This code will not be used until a followup commit to sys/isa/clock.c
and sys/pc98/pc98/clock.c which will only happen after some field testing.
MAC policy. To load a KLD, require that the subject hold Biba privilege,
and the the kernel module be marked as high integrity. To unload a
KLD, require that the subject hold Biba privilege.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
and MLS policies: as we support both an effective (single) element and
range (available) elements, require that the single be in the range if
both the single and range are defined in the update. Remove comments
suggesting that such a check might be a good idea.
Don't introduce a similar check for network interfaces; due to different
interpretations of the single and range elements, it's not clear that
it's useful to do so.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
labeling for Biba.
Rename the variable 'level' to 'type' in interface parsing and
labeling for MLS.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
uio segment is empty. In this case no dma segment is create by
bus_dmamap_load_buffer, but the calling routine clears the first flag.
Under certain combinations of addresses of the first and second mbuf/uio
buffer this leads to corrupted DMA segment descriptors. This was already
fixed by tmm in sparc64/sparc64/iommu.c.
PR: kern/47733
Reviewed by: sam
Approved by: jake (mentor)
some USB devices. (Make sure to set xfer data length when we force
a short inquiry.)
Obtained from: NetBSD(sys/dev/usb/umass_scsipi.c rev.1.8)
Original idea from: Shingo WATANABE <nabe@nabechan.org>
This is a band-aid while I fret over how much breakage removing the
restriction entirely will result in.
Please note that this is still a limit for the entire pathname
relative to the mountpoint of devfs, so the length of "/dev/fd/3"
is 4 characters.
Change the si_name of dev_t's to be a char * and put a private buffer for
holding the name at then end of the struct.
Initialize si_name to point to the private buffer.
Put a KASSERT in geom_disk to prevent overrun on the fake dev_t we still
have to generate for the disk_drivers.
prevent the compiler from optimizing assignments into byte-copy
operations which might make access to the individual fields non-atomic.
Use the individual fields throughout, and don't bother locking them with
Giant: it is no longer needed.
Inspired by: tjr
statclock based on profhz when profiling is enabled MD, since most platforms
don't use this anyway. This removes the need for statclock_process, whose
only purpose was to subdivide profhz, and gets the profiling clock running
outside of sched_lock on platforms that implement suswintr.
Also changed the interface for starting and stopping the profiling clock to
do just that, instead of changing the rate of statclock, since they can now
be separate.
Reviewed by: jhb, tmm
Tested on: i386, sparc64
this will cause volume labels to be exposed in /dev/vol/<volname>. Currently,
there is no conflict resolution if more than one FS has the same volume name.
Reviewed by: phk
of knowing data size transformations of feeder chain and in some cases
this means too much data is pulled through chain, eg converting input
stream from 16bits to 8bits on 16bit only h/w.
PR: kern/37831
Submitted by: Harti Brandt <brandt@fokus.fraunhofer.de>
at 0 as designed. Its BSD adaptation tries to fight it by mapping 0 to
2147483647 after calculation, but this method not works since 2147483647
seed returns to 0 again on the next interation. Instead of after calculation
mapping, map 0 to another value _before_ calculation, so it never stucks.
- Fix overwrite problem of freed buffers. It was rare but could happen
when fwohci_arcv() is called before fwohci_txd() is called for
the transcation.
- Drain AT queues and pend AR queues on SID receive rather than BUS reset to
make sure DMA actually stops.
- Do agent reset in sbp_timeout().
have some negative effect on interactivity but it yields great perf. gains.
This also brings the conditions under which ULE context switches inline
with SCHED_4BSD.
- Define some new kseq_* functions for manipulating the run queue.
- Add a new kseq member ksq_rslices and ksq_bload. rslices is the sum of
the slices of runnable kses. This will be used for push load balance
decisions. bload is the number of threads blocked waiting on IO.
likely not present under the simulator. If multiple partitions are
present on the virtual disk, then the 'a' partition would be the
most logical choice. Nowadays partitions are GPT based, which would
make the assumption of a disklabel even more questionable. Given
all the possible scenarios, assuming a raw "device" seems best.
- Use atomic subtract to update the global wired pages count. (See
also vm/vm_page.c revision 1.233.)
- Assert that the page queue lock is held in pmap_remove_entry().
- Implement TX power control with hints to code in Linux driver
by Douglas S. J. De Couto <decouto@lcs.mit.edu>
- Update ifmedia support to use ieee80211_rate2media and
ieee80211_media2rate. Note doesn't work with stock ifconfig
since there seems to be an issue with the setmedia code.
"ancontrol -t" works now, before it did nothing.
- Fix spelling error in header.
Rename functions bctv_* to bctv2_* and macros BCTV_* to BCTV2_* for
coexistance of BCTV2 and BCTV3.
Rename CARD_IO_GV to CARD_TO_BCTV2.
Add auto recognition of BCTV3/PCI.
PR: i386/43879
Submitted by: MOROHOSHI Akihiko <moro@remus.dti.ne.jp>
Approved by: roger
MFC after: 6 days
saving and restoring ia32 specific registers when switching
context and ia32 support has not been compiled-in. The primary
reason for this change is that one of the ia32 registers (ar.fcr)
is wrongly marked as invalid by the simulator. Now that we avoid
using the register when possible, usability is improved. The
secundary reason is that it saves us 7 loads and stores.
Note that the PCB will continue to have room for these registers,
irrespective of the IA32 option. There are no benefits that make
it worthwhile.
and instead add platform, firmware and EFI stubs to the loader.
The net effect of this change is that besides a special console and
disk driver, the kernel has no knowledge of the simulator. This has
the following advantages:
o Simulator support is much harder to break,
o It's easier to make use of more feature complete simulators.
This would only need a change in the simulator specific loader,
o Running SMP kernels within the simulator. Note that ski at this
time does not simulate IPIs, so there's no way to start APs.
The platform, firmware and EFI stubs describe the following hardware:
o 4 CPU Itanium,
o 128 MB RAM within the 4GB address space,
o 64 MB RAM above the 4GB address space.
NOTE: The stubs in the skiloader describe a machine that should in
parts be defined by the simulator. Things like processor interrupt
block and AP wakeup vector cannot be choosen at random because they
require interpretation by the simulator. Currently the simulator is
ignorant of this.
This change introduces an unofficial SSC call SSC_SAL_SET_VECTORS
which is ignored by the simulator.
Tested with: ski (version 0.943 for linux)
I'm not convinced there is anything major wrong with the patch but
them's the rules..
I am using my "David's mentor" hat to revert this as he's
offline for a while.
