and tabs. This is still not correct for command line variable values
ending in a backslash because this would require a larger effort.
Document this limitation in the BUGS section of the man page. The
quoting is mostly compatible with that of gmake and smake.
Tested by: Max Okumoto and Joerg Sonnenberger from DragonFly BSD
Reviewed by: ru (man page, partly)
suggestions which result in the last revision[*]:
- style(9) and sysexits(3) suggests that we use EX_*
as exit values, instead of some other values like
those returned from a system call as errno.
Additionally, follow Ruslan's suggestion about style(9) and
other style improvements:
- Since open(2) says that it returns -1 on errors,
explicitly determine whether it is returning -1
rather than whether the return value is less than
zero.
- Only set rval when there is no previous error.
This distinguishes the first error that occours.
- Use exit() in favor of return in main(), this is
suggested in old style(9), while the evolve has
fade the suggestion.
- Add some NOTREACHED comments.
- Add blank line after first { because no local variables
in usage()
Thanks to Ruslan for his tireless explaining of the code standards
and knowledge of the history of style(9).
[*] Pointy hat to: me
Submitted by: ru (with some minor changes)
Discussed with: ru, ssouhlal
i386_{get,set}_ioperm() and make those APIs visible in the kernel namespace;
o use i386_{get,set}_ldt() and i386_{get,set}_ioperm() instead of sysarch()
in the linuxlator, which allows to kill another two stackgaps.
MFC after: 2 weeks
the interface when going to toggle VLAN support for
internal reasons. If the IFCAP_VLAN_HWTAGGING bit is
cleared, we should rely on the (re)init routine to turn
VLAN support off and never touch the relevant hardware bits.
This applies to other capability bits, too. The user
obviously has a reason for clearing a capability bit,
e.g., if his particular NIC is buggy and hangs if a
certain hardware capability is turned on even for a
fraction of a second.
The flag adapter->em_insert_vlan_header still is set or
reset irrespective of the IFCAP_VLAN_HWTAGGING setting,
as before, in order to handle the case when a user sets
promiscuous mode on an interface first and later turns
its IFCAP_VLAN_HWTAGGING bit on.
This change might look orthogonal to rev#1.85, but in fact
it is not. It introduces bugfixes that hopefully will make
implementing the general scheme mentioned in the commit
message of rev#1.85 easier.
configuration: it appears to work properly in the non-promiscuous case, but
we've not yet implemented a more general solution that maintains full
functionality with promiscuous mode enabled. While my hope is that we can
get one implemented soon, this will improve functionality substantially in
the mean time.
MFC after: 3 days
AX88190 ones, but that one only minorly):
o don't set flags in the match routine. They appear to be cleared
when probe/attach is called. Before this change, they were
always treated as a simple ne2000, which would fail to get the
right NIC address.
o Lookup device again in the probe routine and probe based on the
cards that you see.
o Detect and report the DL10022 seprately from the DL10019 cards.
While I'm here:
o remove a bad printf
o change another bad printf to device_printf.
o minor style(9) formatting tweaks.
# note: a lot of OEM entries are in the ed_pccard_products such that we can
# likely remove, or collapse, many of them.
This makes all of my DL100xx cards at least probe the ethernet address
correctly, which it wasn't doing before. I can't seem to locate my
AX88xxx based cards, so those haven't been tested, but they were
busted before the change so they can't be any worse now...
address, and additional information. Then the printing of the
ethernet address was moved into ether_attach, and so we were printing
orphaned information about the card. Now the probe message is
prefixed by edX:. Prepare for it to move under bootverbose, but don't
move it there yet (the || 1 trick).
from the userland and pushes results back and the second which does
actual processing. Use the latter to eliminate stackgap in the linux wrapper
of that syscall.
MFC after: 2 weeks
versions of the Racore PC Card Ethernet card. Rearrange to reflect
this reality. This ejects IODATA from 0x1bf, which belongs to Racore.
Thanks to Wilko for providing me with a dumpcis for the DEPCM card.
Also, added Nextcom Nexthawk card from NetBSD
pops data from the userland and pushes results back and the second which does
actual processing. Use the latter to eliminate stackgap in the linux wrappers
of those syscalls.
MFC after: 2 weeks
attributes in casts (i.e. foo = (__stdcall sometype)bar). This only
happens in two places where we need to set up function pointers, so
work around the problem with some void pointer magic.
